还原性有机酸络合铁负载活性炭纤维降解染料废水

采用还原性有机酸络合铁离子并负载到活性炭纤维(ACFs)上,制备出非均相Fenton催化剂用于去除染料废水中有机污染物.采用SEM、FTIR和ICP-AES对制备出的草酸铁(Oxa-Fe)络合物负载ACFs(Oxa-Fe/ACFs-3)进行了表征.发现草酸铁络合物均匀负载在ACFs上,其中铁的质量分数为0.96％.在Oxa-Fe/ACFs-3和H2O2添加量分别为10 g/L和100 mmol/L(以染料废水体积计),50℃条件下对20 mL染料废水进行了降解,染料废水化学需氧量(COD)去除率在100 min内可达62.2％.此外,考察了该催化剂pH适用范围以及重复使用性能.结果表明,Oxa-Fe/ACFs-3促进了H2O2活化产生活性自由基?OH和?O2–,实现了对染料废水中有机污染物的降解.对比了不同还原性有机酸络合铁负载ACFs处理染料废水的性能,发现有机酸还原性越强,越有利于染料废水COD去除率的提高.     

Adhesion and Hydrolytic Stability of the Interface Between High-Modulus Polyethylene Fibers and Acrylic Resins

The effects of oxyen plasma treatment on the surface chemistry of Spectra 1000® high modulus polyethylene fibers and on the mechanical properties of fiber-reinforced composites of the fibers in a Bis-GMA based acrylic resin have been studied. X-ray photoelectron spectroscopy and diffuse reflectance FTIR spectroscopy have been used to show that the majority of oxygen on the fiber surface exists mostly in the form of ether and/or epoxy linkages, with carbonyl-, carboxylic- and ester-containing compounds accounting for less than 10 percent of the total. While the untreated and plasma-treated fibers have similar chemical compositions, the surfaces of the plasma-treated fibers are more polar and the oxygen is chemically bonded instead of being merely physisorbed. The interfacial shear strength between the fibers and the acrylic resin is increased by a factor of 2.3 by the plasma treatment indicating the presence of a weak boundary layer on the surface of the untreated fibers. The hydrolytic stability of the composite interfaces was investigated for fibers sized with several Bis-GMA-based adhesives. Maximum stability was attained by sizing with Bis-GMA containing a peroxide catalyst or an amine accelerator. The flexural properties of composites utilizing plasma-treated and untreated fibers were compared in three-point bending. The ultimate bending loads for composites using treated fibers were much higher than those for composites with untreated fibers, but only a fraction of that for glass or Kevlar®-reinforced materials.     

超滤-反渗透集成工艺处理玉米酒糟废水

研究了玉米酒精生产过程中产生的玉米酒糟废水的膜分离过程,开发了处理玉米酒糟废水的超滤-反渗透集成工艺。超滤选用截留相对分子质量为6 000的GR81PP膜平板分离器,入口压力控制为0.6 MPa,操作温度为50℃;反渗透选用标准脱盐率为90%的ESNAI-4040卷式膜分离器,入口压力控制为2.2 MPa,操作温度为40℃。反渗透透过液中蛋白质的平均截留率为94.70%,甘油的平均截留率为65.15%,COD值降到1 000 mg/L左右,可作为工艺回用水,而且反渗透浓缩液中可回收甘油等有用物质,超滤浓缩液可浓缩成饲料,节能效果显著。     

利谷隆在玉米及土壤中的残留动态

采用高效液相色谱分析技术测定了利谷隆在玉米及土壤中的残留动态和最终残留量。喷施50％利谷隆可湿性粉剂（2812.5g a．i.／hm^2）测出在玉米植株上的残留量较低，施药后14d的残留量仅为0．08mg／kg；土壤中的原始沉积量为7．02mg／kg，半衰期为2．1d，据施药后第14d采样，消解率为72％。利谷隆属于易降解农药。     

Effect of rare earth elements surface treatment on tensile properties of aramid fiber‐reinforced epoxy composites

Solutions of rare earth modifier (RES) and epoxy chloropropane (ECP) grafting modification method were used for the surface treatment of aramid fiber. Tensile properties of both the aramid/epoxy composites and single fibers were tested. The effects of RES concentration on tensile properties of aramid/epoxy composites were investigated in detail to explore an optimum amount of rare earth elements in solution for modifying aramid fiber. The fracture surface morphologies of tensile specimens were observed and analyzed with the aid of SEM. The experimental results show that rare earth treatment is superior to ECP grafting treatment in promoting interfacial adhesion between the aramid fiber and epoxy matrix. Meanwhile, the tensile strengths of single fibers were almost not affected by RES treatment. The optimum performance is obtained when the content of rare earth elements is 0.5 wt %. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1037–1041, 2004     

Surface hydrolysis of filaments based on poly(trimethylene terephthalate) spun at high spinning speeds

The surface alkaline hydrolysis of fibers made from poly(trimethylene terephthalate) (PTT) was studied after extruding the polymer at high spinning speeds from 2000 to 6000 m/min and heat setting in the range of temperatures from 100 to 180°C. Fiber weight loss increased with an increasing heat‐setting temperature but it was also dependent on the spinning speed. Some of the partially hydrolyzed fibers had a well‐developed, hydrophilic surface, and pore size in the range of 0.69 to 1.20 μm. The optimum reaction and morphological conditions for increasing porosity in PTT fibers depends on spinning speed and heat‐setting temperature. A temperature of 180°C is the upper limit for heat‐setting PTT filaments but seems to be the most effective for making porous fibers. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1724–1730, 2004     

Superfine structure,physical properties,and dyeability of alkaline hydrolyzed soly(ethylene terephthalate)/silica nanocomposite fibers prepared by in situ polymerization

In this study, poly(ethylene terephthalate) (PET)/SiO₂ nanocomposites were synthesized by in situ polymerization and melt‐spun to fibers. The superfine structure, physical properties, and dyeability of alkaline hydrolyzed PET/SiO₂ nanocomposite fibers were studied. According to the TEM, SiO₂ nanoparticles were well dispersed in the PET matrix at a size level of 10–20 nm. PET/SiO₂ nanocomposite fibers were treated with aqueous solution of sodium hydroxide and cetyltrimethyl ammonium bromide at 100°C for different time. The differences in the alkaline hydrolysis mechanism between pure PET and PET/SiO₂ nanocomposite fibers were preliminarily investigated, which were evaluated in terms of the weight loss, tensile strength, specific surface area, as well as disperse dye uptake. PET/SiO₂ nanocomposite fibers showed a greater degree of weight loss as compared with that of pure PET fibers. More and tougher superfine structures, such as cracks, craters, and cavities, were introduced, which would facilitate the certain application like deep dyeing. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3691–3697, 2006     

氧化玉米淀粉粘合剂稳定性的探究

探讨了氧化玉米淀粉粘合剂的稳定性的主要影响因素,初步分析其变质机理,以此为依据制备得到高稳定性的产品。     

淀粉-MMA接枝共聚物的半干法合成新工艺

以硝酸铈铵(CAN)为引发剂,采用固相半干法合成了玉米淀粉(CS)接枝甲基丙烯酸甲酯(MMA)共聚物。考察了含水量、反应体系的酸性、反应时间与温度、MMA单体和引发剂CAN用量等因素对接枝共聚反应的影响。结果表明,体系含水质量分数为35%左右,CAN用量为CS质量的1.5%～3%,反应温度在40～50℃,反应时间为0.5h左右,可得到接枝率、接枝效率和单体转化率均较高的接枝共聚物。     

Production of antimicrobially active silk proteins by use of metal‐containing dyestuffs

The work presented here discusses a new technique for preparing silk fibers and films with persistent antimicrobial activity through use of metallic dyestuffs during the fiber dyeing process. The length of the silk fibers investigated contracted when the fibers were immersed in concentrated neutral salt solutions, such as calcium or potassium nitrate, at elevated temperature levels. The birefringence and molecular orientation of the silk fibroin molecules became less ordered by the action of the neutral salt solutions, resulting in increased dyestuff absorption. Subsequently, contracted silk fibers were dyed with metallic dyestuffs containing Cr or Cu for the purpose of obtaining silk fibers with antimicrobial activity. Silk fibers dyed with metallic dyestuffs showed significant antimicrobial activity against the plant pathogen Cornebacterium and the human pathogen Coli bacillus. Tensile strength of the silk fibers after the salt shrinking and dyeing processes did not show a significant change, whereas the elongation at break was increased slightly. The techniques described here for preparing significantly active antimicrobial silk fibers are effective and economic ways of providing new materials for industrial and biomedical applications. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1181–1188, 2002