Microscopic and Macroscopic Growth Rates of Fatigue Cracks in Steels and Alloys under the Influence of Crack Closure

On the basis of the experimental data, we show that the difference between the macroscopic and microscopic fatigue crack growth rates in the second section of the kinetic diagram of fatigue fracture is caused by the effect of crack closure within the limits of its existence. We establish the relationships between the macroscopic and microscopic fatigue crack growth rates and the structure of the material in the second section of the diagram for various values of the load ratio with regard for the effect of crack closure and propose a procedure of examination of the fracture processes in structural materials based on the analysis of microscopic and macroscopic fatigue crack growth rates.     

纳米碳酸钙制备过程中添加剂作用机理探讨

采用鼓泡碳化法 ,在最佳反应温度、反应物浓度的条件下 ,考察了添加剂对产物形状及粒径大小的影响 ,得到了直径为 2 0～ 30nm、长径比在 2 0左右且分散性能良好的针状纳米碳酸钙 ,并对添加剂作用机理进行了分析。     

单晶凝固组织的样品尺寸效应

通过对不同直径的单晶样品的凝固实验，研究了样品尺寸对单晶凝固组织的影响规律，研究发现，随样品尺寸减小，单晶凝固组织被细化，尤其一次枝晶间距λ1和枝晶间γ′相尺寸对样品尺寸的依赖性更为明显；样品尺寸影响的要质在于此表面积的变化，进而对凝固过程温度梯度产生影响，最终作用于凝固组织和力学性能，一次枝晶间距λ1和枝晶间γ′尺寸与样品的比表面积近拟呈线性关系，样品尺寸变化，明显改变了单晶生长过程的温度梯度和合金的高温持久寿命。     

Numerical simulations of specimen size and mismatch effects in ductile crack growth - Part II: Near-tip stress fields

The effect of ductile crack growth on the near tip stress field in two different specimen geometries has been investigated. For homogeneous specimens it is observed that the peak stress level increases with ductile crack growth. The effect is most pronounced up to about 1 mm of crack growth. For low and intermediate hardening there is a significant effect of specimen size on the stress level. In case of mismatch in yield stress, the simulations show that the increase in stress level in the material with the lower yield stress is of a similar magnitude as is the case for stationary cracks. In case of ductile crack growth deviation from the original crack plane occurs, the highest stresses are still found close to the interface, and not in front of the current crack tip.     

Grain Growth Behavior of 5Cr21Mn9Ni4N Steel Micro-Alloyed by Rare Earth

Grain growth behavior of 5Cr21Mn9Ni4NRE steel was experimentally studied at various solid solution treatment temperatures and holding for different times. The experimental results show that the 5Cr21Mn9Ni4NRE steel has the feature of sharp austenite grain coarsening after solid solution treatment at the temperature above 1150 ℃. RE added in the steel has the benefit to restrain grain growth and increase grain growth activation energy.     

三角函数型增长曲线预测油田开发指标

提出了用三角函数表示的一类用于油田开发指标预测的增长曲线共6条，从而进一步完善和丰富了现有的增长曲线法。提出和推导了它们的Np-t、Qt-t、Qt-Np关系式、（Np/NRmax)Qtmax准数计算式以及参数求解式。其特片研究表明，它们特征相近；（Np/NRamx)Qtmax变化范围为0-0.36785，属于峰值产量出现在油田开发初期的情况，其Qt-Np关系为一不对称的拱形曲线。提出了求取曲线参数的过原点重复线性回归法。双河油田的实例表明该方法有一定实用价值。     

Optimized species growth in epoxy polymerization with real-coded NSGA-II

Satisfaction of twin objectives of maximization of M_n along with minimization of PDI do not necessarily guarantee the maximization of concentration of desired species in a semibatch epoxy polymerization process. As the final product consists of a number of polymer species, a need is felt to perform an advanced optimization study to come up with such process conditions for which the selective growth of a particular polymer species is maximized in minimum possible processing time and the population of other species should be at their lowest values. These above-mentioned conflicting objectives frame the platform for a multi-objective optimization problem, which is solved here using a real-coded non-dominated sorting genetic algorithm or NSGA II and Pareto optimal solutions are obtained. The decision variables are discrete addition rates of various ingredients, e.g. the amount of addition of bisphenol-A (a monomer), sodium hydroxide and epichlorohydrin at different time steps. All species balance equations, bounds on M_n, PDI and addition amounts are treated as constraints. Results are very promising in terms of optimized operations for selective enhancement of desired polymer species for the epoxy polymerization process. Total additions are kept very close to available experimental conditions to minimize probable extrapolation errors. It has been observed that preferential oligomer production is extremely difficult for epoxy polymerization. Lower chain polymers are the only choice for a good quality, stable polymer product.     

Grain growth kinetics in Dy-doped Bi0.5Na0.5TiO3 ceramics

Dysprosium-doped bismuth sodium titanate ceramics were prepared using the conventional mixed-oxide method. The amount of dysprosium used was varied from 0 to 2 at.%. The mixed powders were calcined at 800 °C and checked for phase purity using X-ray diffraction technique. The calcined powders were then cold-pressed into pellets and sintered at 1050 °C for the time ranging from 2 to 48 h. The ceramics were checked for phases and microstructures using an X-ray diffractometer and a scanning electron microscope, respectively. The analysis showed that undoped BNT ceramics sintered at longer time exhibited a significant grain growth with non-uniform grain size distribution and shape. The Dy-doped BNT however showed a much more limited grain growth behavior, resulting in smaller grain size and more equiaxed grain shape. It was also found that all Dy-doped BNT ceramics sintered at 48 h possessed lower porosity than those sintered for shorter time.     

Highly oriented star-like patterns observed on GaSe epilayers grown on Si(111)

Epitaxial lamellar gallium selenide (GaSe) semiconductors have been grown on trench-patterned silicon (Si) substrates by molecular beam epitaxy. An intriguing star-like patterned morphology was identified by atomic force microscopy on these epilayers. This non-trivial feature can be correlated with the accumulation of stacking faults of two concurrent epitaxial domains around self-oriented triangular pits developed earlier on the Si(111) surface by the chemical etching. Crystallographic considerations show how the stars can be formed.