Mean residence time of gas in mechanically agitated gas–liquid contactors

In the present study of gas–liquid contactors, mean residence/contact time was calculated from knowledge of superficial velocity and the gas phase hold-up, for various gas rates and impeller geometry and speeds, and compared with values obtained from RTD measurements. A new correlation, involving Flow Number, Froude Number, system geometry and the physical properties, is proposed. This uses the authors data and those available in literature.     

Low temperature delamination of plastic encapsulated microcircuits

Plastic encapsulated microcircuits (PEMs) are increasingly being used in applications requiring operation at temperatures lower than the manufacturer’s recommended minimum temperature, which is 0°C for commercial grade components and −40°C for industrial and automotive grade components. To characterize the susceptibility of PEMs to delamination at these extreme low temperatures, packages with different geometries, encapsulated in both biphenyl and novolac molding compounds, were subjected to up to 500 thermal cycles with minimum temperatures in the range −40 to −65°C in both the moisture saturated and baked conditions. Scanning acoustic microscopy revealed there was a negligible increase in delamination at the die-to-encapsulant interface after thermal cycling for the 84 lead PQFPs encapsulated in novolac and for both 84 lead PQFPs and 14 lead PDIPs encapsulated in biphenyl molding compound. Only the 14 lead novolac PDIPs exhibited increased delamination. Moisture exposure had a significant effect on the creation of additional delamination.     

点阴极电场辅助阳极连接中的紧密接触面积和电流

用等效电路的方法研究了点阴极情况下的电场辅助阳极连接效应，计算了连接电流，连接孕育期和紧密接触面积，本文结果表明，连接初期电流迅速衰减，随后缓慢变小，直至某一稳定值，孕育期随温度上升指数下降，连接温度高时，孕育期将难以观察到；待连接表面之间紧密接触面积随时间延长而非线性扩展，紧密接触区域增大时，其边界向外推进速度渐小，而接触面积增加渐快。     

巴氏杀菌调理食品及其品质控制关键技术

归纳性地介绍了在食品工业发展进程中出现的四种调理食品的显著特点，对其卫生安全性的重要保证措施－灭菌作了一定的理论分析，并阐明了新型巴氏灭菌调理食品的品质控制关键技术。     

分析型全蒸发器在啤酒挥发性成分测定中的应用

综述了分型全蒸发器技术在啤酒发酵过程中的应用状况，并介绍了分析型全蒸发器模型结构及与之配合使用的连续多分支管。     

重载齿轮齿面疲劳损坏及预防

点蚀和剥落是重载齿轮齿面疲劳损坏最普遍的形式.根据齿轮失效分析实例,对齿面初始点蚀、破坏性点蚀和齿面剥落等三种主要疲劳损坏的特征、发生部位及破损危害程度进行了分析研究,较系统地论述了齿轮接触疲劳破坏机理,影响因素及其产生原因,并对有关的齿面破坏提出了相应的预防措施.     

绿色食品与绿色包装

介绍了食品绿色包装与环境保护的关系，探讨了食品绿色包装材料的选择及应用，食品绿色包装设计及市场价值等方面的内容。     

构造作用对油气生成和运聚的影响

有机质从埋藏开始，就处于极其复杂的地球物理化学场中，环境提的能量，一是热量，二是机械能，机械能，主要是通过机械力作用传递给系统的，另外还以机械波的形式赋予系统一定的机械能。当发生断褶构造运动时，机械力对油气运移的影响尤为突出，它经能量的迁移转化，促成了包括机械力降解和地应力驱动等一系列的连锁反应，制造了一次次高效的成油（生运）事件，本文以突变论为着眼点，按照改造控制建造的思路，大胆提出构造运动制造生排烃事件，成就含油气系统的假说。     

回转升降生物接触工艺的实验研究

提出了一种具有特殊运转方式的新型RBC系统－－回转升降生物接触工艺，对回转升降生物接触工艺的工作原理和工艺特征进行了论述。并通过动态实验，对回转升降生物接触工艺小型实验装置的性能和效果进行了初步考察。     

The effect of doubly tapered strut morphology on the plastic yield surface of cellular materials

Although the literature on the mechanics of cellular materials is vast, there is no theoretical model to account for the effects of axial yielding of struts aligned to the applied loading direction on the plastic yield surface under multiaxial loading conditions. An anisotropic hexagonal model having tapered strut morphology is developed to show these effects on the plastic yield surface under multiaxial tensile loading condition. This model covers several types of cellular structure such as two-dimensional (2D) hexagonal and square cellular materials, and three-dimensional (3D) hexagonal and rhombic cellular materials of rod-like columnar structure. A tetrahedral element with tapered strut morphology is also used for a foam model to illustrate these effects on the yield surface under axisymmetric loading condition. Plastic collapse due to bending moment in the inclined struts is a dominant mode. However, under multiaxial tensile loading, the collapse due to axial yielding of struts parallel to the loading direction is found to be an important mode. The shape of plastic yield surface was found to depend not only on relative density but also on the strut morphology.