防振条约束失效对蒸汽发生器传热管面内流弹失稳的影响研究

根据防振条布置以及面内支承连续失效个数，将防振条面内约束失效分析划分为多种工况，分析了不同工况下面内约束失效对传热管面内模态的影响，采用各位置阻尼在振型函数上进行加权平均的方法计算了各阶模态的阻尼比，进而研究了防振条面内不同约束对传热管面内流弹失稳的影响。分析结果表明，随着面内支承连续失效位置的增多，弯管段面内首阶模态频率不断降低，出现在弯管段的振型越加明显；弯管段面内首阶模态不一定是最大流弹失稳比值出现的模态，最大流弹失稳比值出现模态的振型几乎都出现在弯管段；随着面内支承连续失效位置的增多，面内流弹失稳比值不断增大，当连续3个及以上防振条面内约束失效时，将出现流弹失稳现象。     

Unsteady free convection of second‐grade nanofluid with a new time‐space fractional heat conduction

The Caputo and Caputo–Fabrizio derivative are applied to study a second‐grade nanofluid over a vertical plate. A comparative analysis is presented to study the unsteady free convection of a second‐grade nanofluid with a new time–space fractional heat conduction. The governing equations with mixed time–space fractional derivatives are non‐dimensionalized and solved numerically, and a comparison between the Caputo and the Caputo–Fabrizio models is made. It is found that the temperature is higher for the Caputo–Fabrizio fractional model than the Caputo model, but the higher velocity only exists near the vertical plate for the Caputo–Fabrizio model than the Caputo model. Moreover, the velocity for the Caputo model will exceed the Caputo–Fabrizio model as y evolves.     

An experimental study of forced convective heat transfer for fully developed Al 2 O 3 –water nanofluid in an annulus tube

Nanofluids have been known as practical materials to ameliorate heat transfer within diverse industrial systems. The current work presents an empirical study on forced convection effects of Al₂O₃–water nanofluid within an annulus tube. A laminar flow regime has been considered to perform the experiment in high Reynolds number range using several concentrations of nanofluid. Also, the boundary conditions include a constant uniform heat flux applied on the outer shell and an adiabatic condition to the inner tube. Nanofluid particle is visualized with transmission electron microscopy to figure out the nanofluid particles. Additionally, the pressure drop is obtained by measuring the inlet and outlet pressure with respect to the ambient condition. The experimental results showed that adding nanoparticles to the base fluid will increase the heat transfer coefficient (HTC) and average Nusselt number. In addition, by increasing viscosity effects at maximum Reynolds number of 1140 and increasing nanofluid concentration from 1% to 4% (maximum performance at 4%), HTC increases by 18%.     

带有蓄热型直接冷凝式加热板的空气源热泵系统性能研究

针对现有的空气源热泵冬季供热系统，提出了一种使用新型蓄热型直接冷凝式加热板（RHP）的空气源热泵供热系统，并测试了RHP的热性能和系统的运行特性，同时分析了系统的效率和经济性。实验结果表明，在39℃的冷凝温度下，RHP的热容量高达1044 W，RHP的蓄热量大于1000 kJ。在室外空气温度为8℃时，系统COP高达3.7。此外，对于20 m²的居住房间而言，该系统的供暖初始投资成本和总运行成本分别为3174.7 CNY和510.7 CNY，在居住建筑冬季供暖领域具有较大的竞争力。     

Stability and thermophysical properties of fly ash nanofluid for heat transfer applications

Improving the performance of heat transfer fluids is altogether significant. The best approach for improving the thermal conductivity is the addition of nanoparticles to the base fluid. In the present study, specific heat, dynamic viscosity, and thermal conductivity of water-based Indian coal fly ash stable nanofluid for 0.1% to 0.5% volume concentration in the temperature range of 30 to 60°C has been investigated. To evaluate an average particle diameter of 11.5 nm, the fly ash nanoparticles were characterized with scanning electron microscopy and dynamic light scattering. Using zeta potential, the stability of nanofluid in the presence of surfactant Triton X-100 was tested. Thermal conductivity and viscosity of fly ash nanofluid increased, while specific heat decreased as volume concentration increased. The effect of temperature on the fly ash nanofluid was directly proportional to its thermal conductivity and specific heat and inversely proportional to viscosity.     

测试(试井)成果影响因素浅析

随着测试技术的发展、测试质量及资料解释水平的提高，测试（试井）成果的可靠程度越来越受到重视。影响解释成果的环节和因素很多，从客观和主观两方面分析其主要因素，找出症结所在，从而完善现场环节，完善资料解释过程，提高测试技术及解释水平。     

工频有芯感应炉熔沟、三相平衡及热效率分析

介绍了GYT-1.0工频有芯感应炉主要技术性能,分析了新炉的熔沟、三相补偿及热效率.通过与旧炉相比较,说明GYT-1.0工频有芯感应炉具有熔化速度快、热效率高的优点.     

干燥过程中的高温快速工艺

介绍了干燥行业中的高温快速工艺,并利用传热传质原理分析了高温快速工艺干燥速度大、热效率高、物料品质好的原因.     

渣油胶质和沥青质在分散型催化剂作用下的临氢热反应行为

采用四组分法从辽河减压渣油中分离出胶质、沥青质，分别考察了它们在分散型催化剂作用下的临氢热反应行为。结果表明，胶质、沥青质一方面要裂化生成较轻的产物；另一方面也要发生缩合反应生成较重的反应产物以及甲苯不溶物。渣油在临氢热反应过程中，沥青质是生焦的主要来源，其次才是胶质。比较了热反应生成的沥青质与原生沥青质之间以及热反应生成的胶质与原生胶质之间化学组成的区别，结果表明，反应生成的沥青质和胶质较原生的沥青质和胶质分子结构缩合程度高，并且反应苛刻度越高，缩合程度也越高。     

外伴管伴热系统传热特性及优化的数值研究

利用FLUEM软件,对外伴管伴热体系传热特性及其优化进行了数值分析与讨论.分析表明系统中存在传导、对流及辐射传热,其中封闭空气夹层又存在层流自然对流.计入空气对流的模拟表明,工艺管受热不均匀,而伴管布置在其正下方、保持空气层不被保温层挤占可提高伴热效果.伴热平衡时,伴热介质温度、热损失随物料温度近似线性增加.空气层均温假设导致工程设计不合理,而降低工艺管与伴管之间的热阻是提高伴热能力的关键.