河南渑池地区铝土矿工艺矿物学及锂的赋存状态研究

通过河南省渑池地区含锂铝土矿(岩)层工艺矿物学分析,查明铝土矿的物质组成、嵌布特征、伴生锂分布特征和赋存状态,为矿产综合利用提供理论依据。结果显示:该铝土矿Al2O3含量为54.8%,铝硅比值(A/S)为2.6,铝土矿层和粘土岩层中Li2O含量均高于伴生锂边界品位,粘土岩中锂更为富集；矿物组成除一水硬铝石之外,主要是以集合体形态产出的粘土矿物。采用稀酸解析、选矿测试和电子探针分析锂的赋存状态,查明矿石中锂主要是以类质同象置换形式赋存在伊利石和高岭石等粘土矿物中；选矿富锂尾矿中Li2O可富集到0.57%左右,是锂综合回收利用的重点研究对象。      

客车涂装底层材料配套性分析

针对南方客户在使用我司客车一段时间后，车身涂层不同程度出现了起泡的质量问题，进行了现场查看，发现起泡位置在车身左右侧蒙皮，且发生在涂层最底层。初步分析原因是热镀锌板+阴极电泳漆 +原子灰三者之间配套存在问题，通过热镀锌板 +阴极电泳漆 +原子灰三者之间的耐高温 80 ℃配套试验，以及室外曝晒试验，得出镀锌板表面是否钝化、电泳漆膜致密程度和原子灰苯乙烯含量是造成涂层底层起泡的主要原因。为了控制涂层起泡问题，重新修订了我司原子灰、镀锌板、电泳漆的技术标准以及部分工艺文件。     

离子液体体系卤水提锂的洗涤工艺研究

溶剂萃取法是盐湖提锂的重要工艺方法。采用磷酸三丁酯（TBP）/1-丁基-3-甲基咪唑双三氟甲基磺酰亚胺盐（[C₄mim][NTf₂]）离子液体体系对高镁锂比盐湖卤水中的锂进行萃取分离提取实验,对负载有机相的洗涤和反萃过程进行了研究。萃取实验：在TBP与[C₄mim][NTf₂]体积比为9∶1、相比（有机相与水相的体积比）为2∶1条件下,锂离子与其他离子的分离系数分别为β（锂/钠）=94.70、β（锂/钾）=148.85、β（锂/镁）=131.81。洗涤实验：系统考察了洗涤剂种类及浓度、相比、洗涤次数等因素对杂质离子洗脱率的影响,结果发现氯化锂和盐酸的混合溶液是从负载有机相中洗涤除去杂质离子的有效洗涤剂。洗涤过程适宜条件：洗涤剂中氯化锂浓度为4 mol/L、盐酸浓度为0.5 mol/L,相比为5∶1,洗涤次数为2次。反萃实验：用稀盐酸（1.0 mol/L）对负载有机相进行反萃取,在相比为1∶1条件下,单级反萃率达到97.81%。研究表明,离子液体体系作为一种新型萃取体系,在高镁锂比盐湖卤水中提取锂具有较好的应用前景。     

模内装饰薄膜滞热对成型工艺的影响分析

以模内装饰技术(IMD)测试平板为研究对象，利用仿真和实验方法分析薄膜滞热的影响因素及薄膜滞热对成型工艺的影响规律。结果表明，薄膜滞热使动模侧模具温度场变化滞后于定模侧温度场，且在实验条件下达到8.6 ℃的最大温度差；薄膜滞热随着模具温度的增加而降低，随熔体温度和薄膜厚度增加而升高；薄膜影响熔体的充模与冷却，造成产品冷却不均的现象；薄膜滞热导致产品翘曲变形增加。     

转载溜槽衬板磨损预测的DEM仿真方法

针对EDEM自动划分网格较稀疏问题,采用Hypermesh划分仿真模型网格,利用Herz-Mindlin接触理论的Archard磨损模型对转载溜槽磨损问题进行仿真,在网格单元上提取出漏斗和溜管衬板的接触能量和磨损量,分析了磨损量与接触能量的关系。假设转载溜槽衬板磨损深度为物料与溜槽衬板的使用时间为线性函数,根据现场衬板磨损量的测量值,将衬板的磨损系数关系的看作隐式的单变量方程,应用EDEM软件的仿真结果求解出磨损系数的标定值。分析了漏斗和溜管的磨损机理。该方法可用于转载溜槽的磨损预测。     

Simultaneous improvement of thermal conductivity and mechanical properties for mechanically mixed ABS/h-BN composites by using small amounts of hyperbranched polymer additives

Recently, thermal interface materials (TIMs) are in great demands for modern electronics. For mechanically mixed polymer composite TIMs, the thermal conductivity and the mechanical properties are generally lower than expected values due to the sharply increased viscosity and poor filler dispersion. This work shows that addition of a small amount of polyester-based hyperbranched polymer (HBP) avoided the trade-off in mechanically mixed ABS/hexagonal boron nitride (h-BN) composites. After adding 0.5 wt% HBP, the maximum h-BN content in the composites increased from 50 to 60 wt%. The out-of-plane, in-plane thermal conductivity, and tensile strength of ABS/h-BN with 50 wt% h-BN were 0.408, 0.517 W/mK, and 18 MPa, respectively, and were increased to 0.729, 0.847 W/mK, and 32 MPa by adding 0.5 wt% HBP, while 0.972, 1.12 W/mK, and 29.5 MPa were achieved for ABS/h-BN/HBP with 60 wt% h-BN. The morphological and rheological results proved that these enhancements are due to the improved h-BN dispersion by decreasing viscosity of composites during mixing. Theoretical modeling based on the modified effective medium theory confirmed such results and showed that the interfacial thermal resistance also decreased slightly. Thus, this work demonstrates a facile and scalable method for simultaneously improving the thermal conductivity and mechanical properties of thermoplastic-based TIMs.     

Effects of the film thickness and poling electric field on photovoltaic performances of (Pb,La)(Zr,Ti)O3 ferroelectric thin film-based devices

The ferroelectric photovoltaic (FPV) effect obtained in inorganic perovskite ferroelectric materials has received much attention because of its large potential in preparing FPV devices with superior stability, high open-circuit voltage (V_oc) and large short-circuit current density (J_sc). In order to obtain suitable thickness for the ferroelectric thin film as light absorption layer, in which, the sunlight can be fully absorbed and the photo-generated electrons and holes are recombined as few as possible, we prepare Pb_0.93La_0.07(Zr_0.6Ti_0.4)_0.9825O₃ (PLZT) ferroelectric thin films with different layer numbers by the sol-gel method and based on these thin films, obtain FPV devices with FTO/PLZT/Au structure. By measuring photovoltaic properties, it is found that the device with 4 layer-PLZT thin film (~300 nm thickness) exhibits the largest V_oc and J_sc and the photovoltaic effect obviously depends on the value and direction of the poling electric field. When the device is applied a negative poling electric field, both the V_oc and J_sc are significantly higher than those of the device applied the positive poling electric field, due to the depolarization field resulting from the remnant polarization in the same direction with the built-in electric field induced by the Schottky barrier, and the higher the negative poling electric field, the larger the V_oc and J_sc. At a -333 kV/cm poling electric field, the FPV device exhibits the most superior photovoltaic properties with a V_oc of as high as 0.73 V and J_sc of as large as 2.11 μA/cm². This work opens a new way for developing ferroelectric photovoltaic devices with good properties.     

Industry 4.0: a supply chain innovation perspective

The Fourth Industrial Revolution – also known as Industry 4.0 (i4.0) – comprises the digitalisation of the industrial sector. This paper uses the theoretical lens of supply chain innovation (SCI) to investigate the implications of i4.0 on supply chain management. For these purposes, the method of structured content analysis is applied to more than 200 use cases of i4.0-enabled SCI introduced by both established and startup companies. i4.0-enabled SCI manifests along three dimensions: process, technology, and business architecture. The key findings of this study can be summarised as follows: first, i4.0-enabled SCI extends the initial focus on productivity improvements in SC processes towards scalability and flexibility. Second, extant i4.0 solutions rely mostly on analytics and smart things while omitting smart people technology and the human-centric approach associated with the i4.0 paradigm. Third, established companies adopt i4.0 merely to sustain their existing business architectures while startup companies radically change their operating models, relying heavily on data analytics and the platform economy. Consequently, established companies pursue a problem-driven, engineering-based approach to SCI while startup companies follow an ‘asset-light’, business-driven approach. Lastly, there are two distinct approaches to digitalising operational SC processes: platform-based crowdsourcing of standard processes and on-demand provision of customised services.     

Exploring design trade-offs for achieving social inclusion in multi-tiered design problems

ABSTRACT

The digital age of the future is ‘not out there to be discovered’, but it needs to be ‘designed’. The design challenge has to address questions about how we want to live, work, and learn (as individuals and as communities) and what we value and appreciate, e.g.: reflecting on quality of life and creating inclusive societies. An overriding design trade-off for the digital age is whether new developments will increase the digital divide or will create more inclusive societies. Sustaining inclusive societies means allowing people of all ages and all abilities to exploit information technologies for personally meaningful activities. Meta-design fosters the design of socio-technical environments that end-user developers can modify and evolve at use time to improve their quality of life and favour their inclusion in the society. This paper describes three case studies in the domain of assistive technologies in which end users themselves cannot act as end-user developers, but someone else (e.g.: a caregiver or a clinician) must accept this role requiring multi-tiered architectures. The design trade-offs and requirements for meta-design identified in the context of the case studies and other researchers’ projects are described to inform the development of future socio-technical environments focused on social inclusion.     

Off‐grid DoA estimation method of wideband signals

In this paper, an off‐grid direction of arrival (DoA) estimation method is proposed for wideband signals. This method is based on the sparse representation (SR) of the array covariance matrix. Similar to the time domain DoA estimation methods, the correlation function of the sources was assumed to be the same and known. A new measurement vector is obtained using the lower‐left triangular elements of the covariance matrix. The DoAs are estimated by quantizing the entire range of continuous angle space into discrete grid points. However, the exact DoAs may be located between two grid points; therefore, this estimation has errors. The accuracy of DoA estimation is improved by the minimization of the difference between the new measurement vector and its estimated values. Simulation results revealed that the proposed method can enhance the DoA estimation accuracy of wideband signals.