某含锌锡多金属硫化矿石锌浮选试验研究

某含锌锡多金属硫化矿石Zn、Sn、Fe、S含量分别为6.04%、1.05%、29.33%、19.08%，锌主要以铁闪锌矿、闪锌矿的形式存在，锡主要以锡石的形式存在，铁主要以黄铁矿、磁黄铁矿等形式存在，其中的金属矿物共生关系密切，相互包裹现象普遍。为确保不影响后续选锡，对锌浮选流程进行了试验研究。结果表明：矿石在磨矿细度为-0.074 mm占80%的情况下，采用预先脱硫—锌硫混浮再分离流程处理，在选择硫酸铜为锌矿物活化剂、丁基黄药为捕收剂、松醇油为起泡剂、石灰为黄铁矿抑制剂的情况下，经1段脱硫、2粗1扫锌硫混浮、1粗2精锌硫分离，锌硫分离精选尾矿与锌硫混浮扫选精矿2次精选后锌硫分离，最终获得锌精矿Zn品位47.06%、回收率90.76%，试验指标良好。     

一种钛白粉转窑煅烧尾气余热利用新装置

钛白粉煅烧转窑尾气的高湿、高硫、高酸露点的特性使得转窑尾气余热利用过程中换热器寿命不理想。在总结已有尾气余热利用方式存在问题的基础上,提出了一种长寿命、易维护的套管式热管余热利用装置,该装置由彼此分离的换热套管通过弯头、法兰连接成为整体,尾气垂直横掠双层套管段,与高硫、高湿的尾气通过相变介质的相变完成热量由尾气向取热介质的转移,产生钛白粉生产工艺所急需的蒸汽,双层管的相变换热套管对比单层管的重力热管换热器寿命明显延长;连接换热套管的单层管弯头不与高湿、高硫尾气换热,大大减轻了尾气对单层管的腐蚀。换热器应用在3.6 m×58 m的钛白粉煅烧窑上,每年可以产生0.9 MPa的水蒸气1.12万t,为企业带来可观的经济效益。     

机加工孔套管抗挤压强度有限元分析

套管屈服强度直接影响套管抗挤压性能，套管在加工孔过程中可能诱发孔眼附近材料发生金属相变，导致套管屈服强度不再均匀分布，进而影响套管抗挤压强度。在相同工况下，对比了P110完整套管和机加工孔套管的抗挤压强度，以此为参照组分析了相变区域面积和相变区域屈服强度对机加工孔套管抗挤压强度的影响。结果表明，机加工孔会改变材料屈服强度，进而影响套管抗挤压性能。随金属相变区域屈服强度减小，机加工孔套管抗挤压强度减弱；当金属相变区域屈服强度增大时，机加工孔套管抗挤压强度增强。且机加工孔套管相变区域面积对机加工孔套管抗挤压强度的影响随相变区域屈服强度增加而逐渐削弱。     

Influence of Different Additives on the Interaction of Quinolone Antibiotic Drug with Surfactant: Conductivity and Cloud Point Measurement Study

Conductometric and cloud point (CP) measurement studies have been performed to investigate the interaction of tetradecyltrimethylammonium bromide (TTAB) and Triton® X-100 (TX-100) with ciprofloxacin hydrochloride (CFH) in different solvents over the temperature range of 295.15–315.15 K. CFH is used for the treatment of various bacterial infections. The observed critical micelle concentration (CMC) values of TTAB were found to be reduced in the presence of electrolytes (Na₂SO₄/Na₃PO₄), and this reduction proceeds with the elevation of salt concentration. The order of the CMC of TTAB follows the trend: > >. The observed CMC values of TTAB were found to increase with increasing temperature and decrease with increasing concentration of CFH in aqueous medium. The values of Gibbs free energy of micellization () for the TTAB/TTAB + CFH mixture were found to be negative, implying spontaneous micellization. The estimated CP of TX-100 decreases with increasing concentration of TX-100 in aqueous medium. The CP values first decrease with increasing concentration of CFH and then increase at higher concentration of CFH almost in all cases investigated. The values of free energy of clouding were found to be positive in all cases studied implying that phase separation of TX-100 was nonspontaneous. The other thermodynamic parameters associated with the micellization of TTAB and the phase separation of TX-100 were estimated and explained.     

Liquid phase sintering and characterization of SiC ceramics

The present study focuses on the sintering of silicon carbide-based ceramics (SiC) by liquid phase sintering (LPS) followed by characterization of the produced ceramics. AlN/Re₂O₃ mixtures were used as additives in the LPS process. In the first step, the LPS-SiC materials were produced in a graphite resistance furnace in the form of discs at different temperatures. The conditions with the best results regarding real density and relative density were taken as reference for sintering in the form of prismatic bars. In the second step, these samples were evaluated regarding fracture toughness (K_IC), by the Single Edge V Notch Beam – SEVNB – method, and flexural strength. K_IC behavior was evaluated according to the depth and curvature radius of the notches. Reliable K_IC values were presented when the ceramic displayed a small curvature radius at the notch tip. When the radius was large, it did not maintain the square root singularity of the notch tip. Tests were carried out to determine K_IC values in atmospheric air and water. K_IC results were lower in water than air, with a decrease ranging between 2.56% and 11.26%. The observations indicated a direct grain size correlation between K_IC values and fracture strength of the SiC ceramics.     

ZnIn2S4/In(OH)3 hollow microspheres fabricated by one-step l-cysteine-mediated hydrothermal growth for enhanced hydrogen production and MB degradation

An intervening barrier for photocatalytic water decomposition and pollutant degradation is the frustratingly quick recombination of e⁻ - h⁺ pairs. Delicate design of heterojunction photocatalysts by coupling the semiconductors at nanoscale with well-matched geometrical and electronic alignments is an effective strategy to ameliorate the charge separation. Here a facile and environment-friendly l-cysteine-assisted hydrothermal process under weakly alkaline conditions is demonstrated for the first time to fabricate ZnIn₂S₄/In(OH)₃ hollow microspheres with intimate contact, which are verified by XRD, SEM, (HR)TEM, XPS, N₂ adsorption-desorption, UV–Vis DRS and photoluminescence spectra. ZnIn₂S₄/In(OH)₃ heterostructure (L-cys/Zn²⁺ = 4, molar ratio) with a band-gap of 2.50 eV, demonstrates the best photocatalytic performance for water reduction and MB degradation under visible light, outperforming its counterparts (In(OH)₃ and ZnIn₂S₄). The excellent activity of ZnIn₂S₄/In(OH)₃ heterostructure arises from the intercrossed band-edge positions as well as the unique hollow structure with large surface area and wide pore-size distribution, which are beneficial for the efficient charge migration from bulk to surface as well as at the interface between ZnIn₂S₄ and In(OH)₃. This work provides an efficient and eco-friendly strategy for one-pot synthesis of heterostructured composites with intimate contact for photocatalytic application.     

Formation and properties of high entropy oxides in Co-Cr-Fe-Mg-Mn-Ni-O system: Novel (Cr,Fe,Mg,Mn,Ni)3O4 and (Co,Cr,Fe,Mg,Mn)3O4 high entropy spinels

Possibility of formation of quinary and senary equimolar high entropy oxides from the Co-Cr-Fe-Mg-Mn-Ni-O system is presented. Different proposed compositions are synthesized using the solid-state reaction route at high temperatures (900−1100 °C) and quenched to room temperature. Phase composition of the samples is studied, showing tendency toward formation of two main phases: rock salt-structured Fm-3 m and spinel-structured Fd-3 m. It is documented that the annealing temperature has a profound effect on stability of both structures, and at 1100 °C usually the highest content of Fm-3 m phase is usually observed. Three different oxides, namely, (Co,Cr,Fe,Mn,Ni)₃O₄, (Co,Cr,Fe,Mg,Mn)₃O₄ and (Cr,Fe,Mg,Mn,Ni)₃O₄ are obtained as single-phase materials, which structure can be described as the high entropy Fd-3 m spinel one. The latter two compounds have not been previously reported in the literature. Activated character of the electrical conductivity dependence on temperature is observed, with relatively high total conductivity at high temperatures and corresponding high absolute values of Seebeck coefficient.     

单相硼化物的制备及摩擦磨损性能研究

为了深入研究渗硼层中硼化物的性能，采用真空感应熔炼法制备单相硼化物材料。观察分析制备的硼化物微观组织，测试其力学性能。采用MMU-5G型销-盘式摩擦磨损试验机，在干摩擦条件下，研究了不同载荷下单相硼化物的摩擦学性能，观察其磨损表面形貌特征，探讨其磨损方式。结果表明：制备的硼化物为单一相，试样纯度高，试样的平均显微硬度为HV2065，平均断裂韧性值为1.68 MPa·m1/2；硼化物的断口处没有宏观的塑性变形，断口齐平光亮，表现为脆性断裂特征；干摩擦条件下随着载荷从10 N增加到30 N，硼化物的摩擦因数先降低后增加，20 N载荷时达到最小值，而其磨损量随着载荷的增加不断上升；随着载荷从10 N增加到30 N，磨损表面的粗糙度先逐渐上升后急剧上升； 10~20 N载荷下，硼化物的磨损以磨粒磨损为主，而25~30 N载荷下，硼化物的主要磨损方式从磨粒磨损转变为脆性破损。