Comparison of xylo-oligosaccharides production by autohydrolysis of fibers separated from ground corn flour and DDGS

Xylo-oligosaccharides (XOS) are known to have beneficial health properties, and are considered to be functional food ingredients. The objective of this study is to compare corn fibers separated from ground corn flour and distillers dried grains with solubles (DDGS) for XOS yield and optimum autohydrolysis conditions. Based on the initial xylan content, the fiber separated from ground corn flour (FC) resulted in higher XOS yield (71.5%) than the fiber separated from DDGS (FD) (54.6%) at the maximum XOS production conditions. XOS produced were mainly xylobiose and xylotriose. Based on total initial material also, FC resulted in higher XOS yield (8.9%) than FD (8.0%), based on total original masses. Thus, fiber separated from ground corn flour would be a better feedstock for production of XOS than fiber separated from DDGS. The conditions for maximum XOS production from FD and FC were 180 °C with 20 min hold-time and 190 °C with 10 min hold-time, respectively.     

Electrophoretic deposition of graphene oxide on carbon brush as bioanode for microbial fuel cell operated with real wastewater

Microbial fuel cell (MFC) is a promising technology for simultaneous wastewater treatment and energy harvesting. The properties of the anode material play a critical role in the performance of the MFC. In this study, graphene oxide was prepared by a modified hummer's method. A thin layer of graphene oxide was incorporated on the carbon brush using an electrophoretic technique. The deoxygenated graphene oxide formed on the surface of the carbon brush (RGO-CB) was investigated as a bio-anode in MFC operated with real wastewater. The performance of the MFC using the RGO-CB was compared with that using plain carbon brush anode (PCB). Results showed that electrophoretic deposition of graphene oxide on the surface of carbon brush significantly enhanced the performance of the MFC, where the power density increased more than 10 times (from 33 mWm^?2 to 381 mWm^?2). Although the COD removal was nearly similar for the two MFCs, i.e., with PCB and RGO-CB; the columbic efficiency significantly increased in the case of RGO-CB anode. The improved performance in the case of the modified electrode was related to the role of the graphene in improving the electron transfer from the microorganism to the anode surface, as confirmed from the electrochemical impedance spectroscopy measurements.     

基于随机光栅的可调谐随机光纤激光器

提出一种基于随机光栅与高反射布拉格光栅(FBG)相结合的可调谐随机光纤激光器。利用980nm泵浦光源泵浦一段7m长的掺铒光纤(EDF)进行增益放大,由随机光栅提供随机反馈。随机光栅长7cm,具有约10000个折射率修改点,这些点由飞秒激光逐点写入,并沿光纤方向随机分布,两点相邻间隔小于10μm。同时,利用中心波长为1548nm的高反射FBG来组成半开放腔结构,实现了随机激光的输出。实验测得的泵浦阈值功率仅为18mW,斜率效率高达13.2%,并通过改变FBG的中心波长,实现了输出激光波长的可调谐,调谐范围为4.45nm(1548.04~1552.49nm)。得益于半开放式激光腔的设计和EDF的高增益,整个系统具有阈值低、效率高、结构简单等优点。     

柠条的纤维特性及其双螺杆CMP制浆性能研究

以柠条为原料，分析了其化学组分和纤维形态，并探讨了柠条双螺杆CMP法的制浆工艺以及浆料的纤维形态和成纸的物理性能。研究结果表明：与针、阔叶木相比，柠条原料中纤维素和综纤维素质量分数较低，苯醇抽出物和热水抽出物质量分数较高，柠条纤维长度总体偏短，木质部和皮部的纤维质量平均长度分别为0.621和0.819 mm，还存在部分杂细胞。采用3.5% Na₂SO₃和1.5% NaOH常温预浸12 h、90℃汽蒸1 h后再用双螺杆挤浆机在质量分数35%下进行搓丝，并结合高浓盘磨机磨浆，所得CMP浆得率可达73%。柠条CMP浆基本保持了纤维原有的长度，质量平均长度达0.650 mm，长宽比为32.7，纤维解离较好，但分丝帚化情况不理想，含有部分纤维束和杂细胞。当加拿大游离度为300 mL时，柠条CMP浆成纸的环压强度指数和松厚度较高，分别为8.67（N·m）/g和2.56 cm³/g，抗张指数为19.6（N·m）/g，本色浆白度较高，达50%（ISO）。柠条CMP浆适合配抄瓦楞原纸等包装用纸，漂白后可配抄新闻纸和白板纸。     

燃煤锅炉除尘专用滤料的开发

介绍机械制造厂燃煤锅炉的烟尘特点,分析滤料失效的原因,提出一套针对该工况的滤料解决方案。介绍针对复杂工况条件所选用的纤维种类以及复合面层原料成分配比的确定,最终选用针刺工艺加工并对该新产品的基本性能进行了测试分析。     

Design criterion for fatigue strengthening of riveted beams in a 120-year-old railway metallic bridge using pre-stressed CFRP plates

This study presents a design criterion developed for fatigue strengthening of a 120-year-old metallic railway bridge in Switzerland and presents a pre-stressed un-bonded reinforcement (PUR) system developed to apply the strengthening. The PUR system uses carbon fiber reinforced polymer (CFRP) plates; however, unlike conventional pre-stressed CFRP reinforcement methods, preparation of the existing metallic bridge surface is not required. This decreases the time required for on-site strengthening procedures. The principle of the constant life diagram (CLD) and two fatigue failure criteria (Johnson and Goodman) are described. Analytical formulations are developed based on the CLD method to determine the minimum CFRP pre-stress level required to prevent fatigue crack initiation. The PUR system uses an applied pre-stress force to reduce the mean stress level (and stress ratio) to shift an existing fatigue-susceptible metallic detail from the ‘at risk’ finite life regime to the ‘safe’ infinite life regime. The applied CLD method is particularly valuable when the stress history of the detail is not known and it is difficult to assess the remaining fatigue life. Moreover, it is shown that the currently adopted approach in many structural codes which emphasizes stress range as the dominant parameter influencing fatigue life are non-conservative for tension–tension stress patterns (i.e., stress ratios of 0 < R < 1). Analyses show that the modified Johnson formula accurately reflects the combined effect of stress range, mean stress level, and material properties, and offers a relatively easy design procedure. Details of a retrofit field application on members of a riveted wrought iron railway bridge are given. A wireless sensor network (WSN) system is used for long-term monitoring of the on-site CFRP stress levels and temperature of the retrofitted details. WSN measurements indicate that increases in ambient temperature result in increased CFRP pre-stress levels.     

玄武岩纤维填料应用于两种混合生长反应器的评价

采用单丝直径微米级的伞状玄武岩纤维(BF)作为填料,将其引入序批式反应器(SBR)和后置缺氧反硝化SBR外聚合物(EPS)含量和扫描电子显微镜形貌图,考察了两种SHBR的污水处理效果。试验结果表明:基于SBR的SHBR的出水COD、氨氮、总氮去除率分别为83.2%、89.9%、86.8%;基于后置缺氧反硝化SBR的SHBR优良,而基于后置缺氧反硝化SBR的SHBR的脱氮效果得到进一步的优化和提升。两种SHBR的BF填料中EPS含量分析结果显示:在好氧环境下,蛋白质(PN)的含量高于多糖(PS)的含量;在缺氧条件下,PS的含量明显高于PN的含量。     

Simultaneously enhancing mechanical and microwave absorption properties of Cf/SiC composites via SiC nanowires additions

C_f/SiC composite is an excellent structural and functional material, silicon carbide nanowires (SiCnws) are not only a toughening material but also a great application in the field of microwave absorption. In this study, SiCnws are grown on the surface of carbon fiber (C_f) by polymer impregnation and pyrolysis, and the SiC matrix was prepared by chemical vapor osmosis method. The SiCnws are introduced to enhance the mechanical and microwave absorption properties simultaneously. After 3 impregnations, the flexural strength of the composite was 107.35 ± 10 MPa. When the thickness is 1.86 mm, the minimum reflection loss value is ?41.08 dB, and the effective absorption bandwidth (RL ≤ ?10 dB) is 3.86 GHz. Furthermore, the microwave absorption mechanism of the material is discussed. This work provides a new method to prepare lightweight, stable and high-performance microwave absorption materials, and these materials are expected to be used in high temperature environments.     

Compressive strength and wear properties of SiC/Al6061 composites reinforced with high contents of SiC fabricated by pressure-assisted infiltration

Pressure-assisted infiltration was used to synthesize SiC/Al 6061 composites containing high weight percentages of SiC. A combination of PEG and glass water was used to fabricate SiC preforms and the effect of the presence of glass water on the microstructure and mechanical properties of the preforms was evaluated by performing compression tests on the preforms. Also, the compressive strength and the hardness of the SiC/Al composites were investigated. The results revealed that the glass water improved the compressive strength of the preforms by about five times. The microstructural characterization of the composites showed that the penetration of the aluminum melt into the preforms was completed and almost no porosity could be seen in the microstructures of the composites. Moreover, the composite containing 75 wt% SiC exhibited the highest compressive strength as well as the maximum hardness. The results of the wear tests showed that increasing the SiC content reduces the wear rate so that the Al-75 wt% SiC composite has a lower wear rate and a lower coefficient of friction than those of Al-67 wt% SiC composite. This indicated higher wear resistance in these composites than the Al alloy due to the formation of a tribological layer on the surface of the composites.     

Combining molybdenum carbide with ceria overlayers to boost Mo/CeO2 catalyzed ammonia synthesis

The design of an efficient non-noble metal catalyst is of burgeoning interest for ammonia synthesis. Herein, we report a Mo₂C/CeO₂ catalyst that is superior in ammonia synthesis activity. In this catalyst, molybdenum carbide coexisted with the ceria overlayers which is from the ceria support as the strong metal–support interaction. There is a high proportion of low-valent Mo species, as well as high concentration of Ce³⁺ and surface oxygen species. The presence of Mo₂C and CeO₂ overlayers not only leads to enhancement of hydrogen and nitrogen adsorption, but also facilitates the desorption and exchange of adsorbed species with the gaseous reagents. Compared with the Mo/CeO₂ catalyst prepared without carbonization, the Mo₂C/CeO₂ catalyst is more than sevenfold higher in ammonia synthesis rate. This work not only presents an explicit example of designing Mo-based catalyst that is highly efficient for ammonia synthesis by tuning the adsorption and desorption properties of the reactant gases, but opens a perspective for other elements in ammonia synthesis.