Simplified anode architecture for PEMFC systems based on alternative fuel feeding: Experimental characterization and optimization for automotive applications

The need to reduce PEMFC systems cost as well as to increase their durability is crucial for their integration in various applications and especially for transport applications. A new simplified architecture of the anode circuit called Alternating Fuel Feeding (AFF) offers to reduce the development costs. Requiring a new stack concept, it combines the simplicity of Dead-End Anode (DEA) with the operation advantages of the hydrogen recirculation. The three architectures (DEA, recirculation and AFF) are compared in terms of performance on a 5-kW test bench in automotive conditions, through a sensitivity analysis. A gain of 17% on the system efficiency is observed when switching from DEA to AFF. Moreover, similar performances are obtained both for AFF and for recirculation after an accurate optimization of the AFF tuning parameters. Based on DoE data, a gain of 25% on the weight of the anodic line has been identified compared to pulsed ejector architecture and 43% with the classic recirculation architecture with blower only (Miraï).     

An integrated approach to analysing the cost efficiency of postal networks

An integrated approach to measure the cost efficiency of the postal network of Universal Service Provider is proposed. An integrated approach enables the measurement of cost efficiency for delivery and non-delivery postal network units. The proposed approach is verified and tested on the postal network of the selected provider and the results were derived by using Data Envelopment Analysis (DEA). The results show that the main sources of inefficiency are inadequate allocation of resources relative to the network units. In addition, the study indicates that economies of scale have a positive impact on the efficiency of postal network units.     

燃料电池空气电极的孔道结构调控

燃料电池是将化学能转化成电能的装置，其空气电极催化层的设计，既要包含丰富的、易于接近的反应活性位，也要具备高度连通的电子、质子以及反应物、产物传质通道，因此电极必须具有特定三维几何结构形貌和有序分布的各功能化孔道，确保催化活性位得以充分利用以及反应可以连续进行。针对催化剂孔道的几何结构调控，本文调研了最近报道的一系列研究工作，从模板法、高温相变法、模板/相变复合方法以及基于金属有机框架材料进行孔道设计等四种主要方法出发，综述了该领域的最新研究进展。     

南水北调中线工程受水区二期需调水量预测研究

2002年12月国务院批复了《南水北调工程总体规划》，明确中线工程分两期建设。目前，一期工程已经通水。近年来，随着社会经济的快速发展，受水区的人口、生产规模、节水水平、人们对环境的要求都发生了变化，因此有必要根据新的情况对受水区的用水需求重新预测。分析了城市化发展和城镇用水变化的新形势，依据流域、区域水资源规划成果，提出了中线二期工程受水区需调水量，并与《南水北调中线工程规划》提出的二期需调水量进行对比，以供各方参考。     

多晶硅锭中硬质点分析及控制研究

以多晶硅锭中硬质点为研究对象,通过实验研究和数值模拟的方法,对多晶硅锭中硬质点进行形貌和成分分析,并提出改善控制方法。研究结果表明硅锭中部的硬质点较细小,主要由SiC组成;硅锭头部的硬质点较粗大,主要由SiC和Si3N4组成,还有少量O的存在。进一步研究发现多晶硅定向凝固铸锭炉的热场结构对于多晶硅锭硬质点形成有直接影响,通过改进热场结构,优化晶体生长界面,显著减少了铸锭中硬质点的数量。     

2014~2018年福建省生产领域纸巾纸荧光物质质量分析

对福建省生产领域近五年的纸巾纸进行随机抽样和质量分析,检测了产品的可迁移性荧光物质指标。结果显示:纸巾纸产品的可迁移性荧光物质指标共出现5批次不合格产品,产品合格率为98.7%,呈现较高的质量水平;纸巾纸的荧光物质检出率近五年呈现先上升后下降的趋势,2015年出现检出率峰值,其值为15.0%,2018年降为0%。按地域统计,福州地区出现3批次可迁移性荧光物质的纸巾纸产品,产品合格率为95.2%;其余地市的产品合格率均为100%。同时,福州纸巾纸产品荧光物质检出率最高,检出率达到12.7%。按产品质量等级统计,纸巾纸优等品的产品质量总体高于合格品的。     

A new wavelet based fault detection,classification and location in transmission lines

This paper deals with the application of wavelet transforms for the detection, classification and location of faults on transmission lines. A Global Positioning System clock is used to synchronize sampling of voltage and current signals at both the ends of the transmission line. The detail coefficients of current signals of both the ends are utilized to calculate fault indices. These fault indices are compared with threshold values to detect and classify the faults. Artificial Neural Networks are employed to locate the fault, which make use of approximate decompositions of the voltages and currents of local end. The proposed algorithm is tested successfully for different locations and types of faults.     

The formation of fibrous structure of polyamide 6 induced by the three-step forming process and its prominent reinforcement in nitrile rubber

Nitrile rubber (NBR) blends with excellent performance have always been a hot research topic in petroleum field. Due to the excellent performance and compatibility of polyamide 6 (PA6), it provides an opportunity for the preparation of high-performance NBR/PA6 blends. In this article, NBR/PA6 blends were prepared by the three-step molding process. Experimentally, it was found that PA6 has a prominent reinforcement effect in NBR matrix. The variation of this mechanical property was investigated from different aspects of the crystal structure, crystallinities, phase morphology, and so on. It can be cleared that the formation of fibrous structure of PA6 phase is the main factor for reinforcement of the polymer blends. Meanwhile, the formation mechanism of the special phase structure induced by the three-step process is deeply expounded and its structural evolution schematic is established. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47472.