光折变三维信息存储器

分析光折变三维存储器的机理,探讨了光折变三维存储器的编码方式、光折变材料的选择及存储技术,阐述了其产业化进程.     

泌阳凹陷新庄辫状三角洲沉积体系及储集性能

依据岩心和测井资料，对泌阳凹陷新庄辫状三角洲沉积体系进行了沉积微相划分和微相特征分析。在此基础上，进行了沉积模式和油气储集性能的研究。研究认为，水下分流河道、河口砂坝是该区最好的油气储集体，其它微相依次为辫状河道、浊积岩、前缘席状砂和决口扇。研究结果可为下一步的滚动勘探提供地质依据。     

伶仃洋三维潮流输沙的数值模拟

作者使用垂向坐标变换技术，结合有限差分方法建立了三维潮流输沙的数学模型。为了增加模型的稳定性和减少数值耗散，对悬沙对流扩散方程中的水平对流项采用三阶迎风格式离散。应用本模型对伶仃洋的枯季和洪季的潮流输沙的悬沙场进行了数值模拟，将模拟结果与实测资料进行比较，二者吻合较好。模拟结果分析表明：伶仃洋悬沙运动主要集中在西滩，对伶仃航道影响不大；洪季水体含沙浓度高于枯季；水体含沙浓度沿水深存在浓度梯度，且洪季的浓度梯度明显大于枯季。     

Measurement and numerical simulation of three‐dimensional fiber orientation states in injection‐molded short‐fiber‐reinforced plastics

To determine three‐dimensional fiber orientation states in injection‐molded short‐fiber composites, a confocal laser scanning microscope (CLSM) is used. Since the CLSM optically sections the specimen, more than two images of the cross sections on and below the surface of the composite can be obtained. Three‐dimensional fiber orientation states can be determined by using geometric parameters of fiber images obtained from two parallel cross sections. For experiments, carbon‐fiber‐reinforced polystyrene is examined by the CLSM and geometric parameters of fibers on each cross‐sectional plane are measured by an image analysis. In order to describe fiber orientation states compactly, orientation tensors are determined at different positions of the prepared specimen. Three‐dimensional orientation states are obtained without any difficulty by determining the out‐of‐plane angles utilizing fiber images on two parallel planes acquired by the CLSM. Orientation states are different at different positions and show the shell–core structure along the thickness of the specimen. Fiber orientation tensors are predicted by a numerical analysis and the numerically predicted orientation states show good agreement with measured ones. However, some differences are found at the end of cavity. They may result from the fountain flow effects, which are not considered in the numerical analysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 500–509, 2003     

改性双马来酰亚胺的研究

本文研究了双马来酰亚胺与烯丙基化合物形成的改性树脂体系的固化和热性能，讨论了单体配比、增韧剂、催化剂对性能的影响。     

真空铸造高强度C/Mg复合材料

本文介绍用真空铸造法制造抗拉强度超过1000MPa的高强度C/Mg复合材料。将T300纤维经C-Si-O梯度涂层处理后单向排布于型腔内,在真空下注入ZM-5合金液,凝固后即得C/Mg复合材料零件或试样。试样的抗拉强度在纤维体积分数为0.35时达1050MPa。本文讨论C-Si-O梯度涂层对获得高强度复合材料的作用。     

Formation and growth mechanism of TiC crystal in TiC_p/Ti composites

1　ＩＮＴＲＯＤＵＣＴＩＯＮＰａｒｔｉｃｌｅｓｒｅｉｎｆｏｒｃｅｄｔｉｔａｎｉｕｍａｌｌｏｙｍａｔｒｉｘｃｏｍｐｏｓｉｔｅｓ(ＴＭＣｐ)ｈａｖｅｗｉｄｅａｐｐｌｉｃａｔｉｏｎｆｉｅｌｄｓｆｏｒｔｈｅｉｒａｔｔｒａｃｔｉｖｅｈｉｇｈｓｐｅｃｉｆｉｃｓｔｒｅｎｇ     

纤维增强铝基复合材料变形损伤过程声发射研究

采用声发射（ＡＥ）技术，通过测定ＡＥ事件数、幅度和持续时间等发射特征参数以及恒载 Ｆｅｌｉｅｉｔｙ效应，对ＳｉＣ／Ａｌ和Ｃ／Ａｌ两类束丝纤维增强铝昨合在拉伸变形过程中的损失失效特征进行了分析探讨。实验结果表明，纤维种类、界面状况对复合材料损伤过程有着显著的影响，声发射技术是表征这类复合材料损伤特征很有潜力的方法。     

Processing and microstructure of non-oxide ceramic fibres

Research and development efforts on high-temperature, oxidation-resistant fibres have increased over the past decade due to the demand for light-weight, stiff and strong composite materials in aerospace applications. Varieties of ‘high-performance’, continuous, non-oxide fibres with low-density, high tensile strength and tensile modulus have been developed either from organic precursors or via chemical vapour deposition for fabrication of ceramic matrix composites. Fibres derived from polymer precursors (e.g. Nicalon, Tyranno, HPZ) are small in diameter (compared to CVD monofilaments) and are ideally suited for ceramic composites. Processing, microstructural stability and mechanical properties of these newly developed SiC and Si₃N₄ base fibres are briefly reviewed in this paper.     

CF/ABS树脂复合材料制备工艺对导电性能的影响及对屏蔽性能的理论预测

本文研究了使用溶剂法、密炼机和开炼机混炼碳纤维填充ABS树脂复合材料的导电性能,得到了纤维填充量与复合材料电阻率的关系,对其导电机理进行了分析.通过比较,发现纤维长径比是决定复合材料导电性能的重要因素,其它如纤维在基体中的分布也对复合材料导电性能有影响.最后对复合材料的屏蔽性能进行了理论计算.