台北101层国际金融中心之结构施工技术与其设计考量概述

本文旨在简要说明目前正在施工中之超高层大楼—台北国际金融中心之结构系统、钢结构工程、钢筋混凝土工程基础与深开挖工程等特殊施工技术,并佐以相关之设计考量与施工规划概要,以供工程界做参考。     

Characteristics of hydrostatic bearing/seal parts for water hydraulic pumps and motors. Part 1: Experiment and theory

In this paper, the load-carrying capacity, power losses and stiffness of disk-type hydrostatic thrust bearings including the case of eccentric loading are discussed theoretically. The numerical analysis method is established based on a two-dimensional elastohydrostatic problem with an elastic deformation model, which is extended to adapt it for a non-axisymmetric load acting on the thrust bearing. The bearing is made of a combination of stainless steel/stainless steel and stainless steel/plastics. For the elastic materials, the maximum stiffness derived from, i.e., minimum film thickness is, larger than that of the rigid material in the range of a large ratio of pocket pressure and a hydrostatic balance ratio of over unity, which is defined as the ratio of the load to the maximum hydrostatic load-carrying capacity. The maximum load-carrying capacity and minimum power loss can exist in the domain of the hydrostatic balance ratio over unity for the case of the bearing consisting of elastic/rigid materials, in comparison with that composed of the same rigid materials. For the case of water, the power loss due to leakage flow is slightly larger but that due to frictional torque is much smaller than that in the case of hydraulic oil. Then, the total power loss is much smaller than that of hydraulic oil.     

湿硫化氢环境下的球罐腐蚀状况分析

在湿硫化氢环境下 ,尤其储存介质中的硫化氢含量超标时 ,很容易对储存容器壳体 (含焊缝和母材 )造成硫化氢应力腐蚀或氢鼓包。作者较仔细分析了 1 0 0 0m3 丙烯球罐产生硫化氢应力腐蚀开裂和40 0m3 LPG球罐产生氢鼓包的原因。提出了此类设备在设计选材、设备制造、施工安装和使用维护等环节应注意的问题。     

一种900-MHz 20-mW CMOS功率放大器的设计

提出了一个工作电压为3V，工作频率900MHZ，输出功率为20mW的高效率CMOS功率放大器。为了达到设计目标，文章采用了一些特殊的方法，包括三级放大结构，级间的调谐匹配和层叠差分结构。     

Failure analysis of aluminum cable steel reinforced (ACSR) conductor of the transmission line crossing the Paraná River

The failure of the conductor of the 460 kV overhead transmission line located along the crossing of the Paraná River was investigated. As a result of this failure, a blackout took place in the southern states of Brazil in January of 2002, reaching approximately 67 million inhabitants. Investigation of the external aluminium layer of the ACSR conductor near the fracture showed typical static deformation marks and dynamic fretting wear tangential marks, both associated with the presence of Al₂O₃ debris. Additionally, encrusted silicon particles were observed on the external surface of the strands. The internal Al layer showed elliptical deformation marks also associated with Al₂O₃ debris. Both Al₂O₃ and Si particles are efficient abrasive material, which associated with slight relative motion of metallic surfaces (clamp/strand and strand/strand) can promote fretting wear. Two types of fracture surface of the Al strands were identified: 45° and quasi-normal surfaces, the former being the predominant type. Delamination and particle detachment were the mechanisms of superficial degradation observed on the Al strands, indicating that the rupture of the strands occurred under a gross slip fretting regime induced by sub-conductor oscillation. Inspection of the internal surface of as-cast Al–10%Si spacer clamps revealed different stages of intense circumferential wear caused by the preferential cracking and particle detachment of the eutectic constituent of the as-cast microstructure. This intense wear reduces the clamping contact pressure, which allows higher displacement amplitude and leads to the critical fretting regime. Finally, a few suggestions are discussed to minimise the occurrence of future failures.     

开工生产装置改扩建施工防火安全管理手段和举措

系统地分析了开工生产装置改扩建施工的特点及其火灾危险性,在此基础上提出了改扩建施工现场的防火安全管理手段和应采取的防火安全措施。     

万家寨引黄工程南干线国际Ⅱ、Ⅲ标区段安全监测工程的施工

万家寨引黄工程安全监测工程随主体工程分布于全线,并与全线自动化控制工程连接,实现近地/远地控制式的运营管理,本文将国际Ⅱ、Ⅲ标段安全监测工程作为典型代表工程,主要介绍安全监测工程的施工方法以及监测项目和断面布置等。     

钻机柴油机的动向和190系列柴油机的发展

本文概括介绍了国内外钻机柴油机发展的水平及动向,比较了国内钻机柴油机与国外钻机柴油机在发展上的差距。重点介绍了作为国产钻机主要动力的190系列柴油机的发展状况及最新技术在该机型上的应用。     

加强和改进施工企业党组织建设的途径

推进施工企业党组织的建设必须与时俱进,坚持一岗双责、两个融合、三个同步、四个同时,创新工作思路、工作机制、工作方法和工作方式。把贯彻落实“三个代表”重要思想,作为检验工作成效的根本标准。     

浅谈等电位联结的施工

本文讨论了等电位联结,以及等电位联结安装在施工中存在的不足,并提出施工安装中应注意的问题。