浅谈电动潜油单螺杆采油系统的研究开发

介绍了国内外各种螺杆泵采油系统的发展现状，并对电动潜油螺杆泵采油系统中齿轮减速器这一关键部件的方案选择进行了分析，旨在为研制开发国产高性能电动潜油螺杆采油系统提供参考。     

基于ANN和SA的混凝土配合比优化设计

利用模拟退火方法探讨了混凝土配合比的优化设计，并用Visual C＋＋语言编制了实用系统，得出了只要数据充分，算法的精度可以得到保证的结论，以推广该设计方法的应用。     

转向柱管承载能力的试验研究

在分析转向柱管花键部位应力集中情况的基础上,通过对某厂生产的转向柱管扭转破坏的试验研究,得到如下结论:①转向柱管的承载能力与其外花键齿与方向盘中心内花键齿之间的非接触区长度有关,以花键端部过渡圆弧的直径大小为宜;②安装方向盘总成时所施加在安装螺母上的拧紧力矩在70N.m左右时,转向柱管的承载能力最大。     

Non‐reflecting artificial boundaries for transient scalar wave propagation in a two‐dimensional infinite homogeneous layer

This paper presents an exact non‐reflecting boundary condition for dealing with transient scalar wave propagation problems in a two‐dimensional infinite homogeneous layer. In order to model the complicated geometry and material properties in the near field, two vertical artificial boundaries are considered in the infinite layer so as to truncate the infinite domain into a finite domain. This treatment requires the appropriate boundary conditions, which are often referred to as the artificial boundary conditions, to be applied on the truncated boundaries. Since the infinite extension direction is different for these two truncated vertical boundaries, namely one extends toward x →∞ and another extends toward x→‐ ∞, the non‐reflecting boundary condition needs to be derived on these two boundaries. Applying the variable separation method to the wave equation results in a reduction in spatial variables by one. The reduced wave equation, which is a time‐dependent partial differential equation with only one spatial variable, can be further changed into a linear first‐order ordinary differential equation by using both the operator splitting method and the modal radiation function concept simultaneously. As a result, the non‐reflecting artificial boundary condition can be obtained by solving the ordinary differential equation whose stability is ensured. Some numerical examples have demonstrated that the non‐reflecting boundary condition is of high accuracy in dealing with scalar wave propagation problems in infinite and semi‐infinite media. Copyright © 2003 John Wiley & Sons, Ltd.     

齿科微晶玻璃的腐蚀机理及溶胶-凝胶防腐蚀涂层研究

利用体外试验方法以及SEM／EDAX、ICP、FTIR等分析技术，对氟硅碱钙石(fluorcanasite,K2Na4Ca5Si12O30F4)齿科微晶玻璃的腐蚀机理，以及溶胶-凝胶Al2O3，、TiO2及ZrO2涂层改善微晶玻璃抗侵蚀的效果进行了比较分析．研究表明，口腔溶液对该齿科微晶玻璃的侵蚀源于溶液中的H3O 离子与微晶玻璃表面的Na 及K 发生迅速的离子交换，从而形成结构疏松的表面富SiO2层，其Si-O网络进而被H2O分子所断开，使SiO2以可溶性硅胶形式溶解于溶液中．此反应导致大量的表面结构缺陷，从而降低了材料的强度和使用寿命。浸泡25天后微晶玻璃表面最终的反应产物是一层低结晶度的颗粒状碳酸羟基磷灰石Cal0(PO4)6(2OH-，CO3^2-)．溶胶-凝胶A12O3涂层具有显著的改善齿科微晶玻璃抗唾液腐蚀的作用。     

Bioprocess applications of model-based estimation techniques

The last decade has seen the development of a number of approaches for estimating those variables which are difficult to measure on-line in industrial process situations. Whilst a range of techniques is available, a common element is the use of process knowledge in the form of a system model. In the case of bioprocess systems, although a large range of models has been presented in the literature, their use in estimation schemes on an industrial scale has been limited. A number of reasons can be identified for their low level of utilisation. Of particular significance is the uncertainty which exists in quantifying system performance and the process-model mismatch which inevitably results. The level of ‘pre-defined model’ uncertainty, together with the knowledge gained during the course of the fermentation, serves to dictate estimator structure. The paper considers a range of estimation strategies and contrasts, through industrial applications, their performance characteristics and utility.     

SC文法功能体系

文法体系的研究一直是自然语言处理研究的核心问题之一.但是,由于自然语言本身所固有的复杂性和非规范性,多义问题始终未能得到圆满的解决.本文提出了SC文法(A SubCategory grammar for integrating Se-mantic and Case analysis),它是一种基于传统的上下文无关文法、语义文法,以及超前与反馈分析技术和格框架约束分析等技术的上下文相关处理文法.该文法不仅能继承传统的上下文无关文法的表示简洁、处理方便的特点,而且能实现语法和语义一体化分析和处理上下文相关以及复杂多义问题.     

骑马岭水电站砂石加工系统规划设计

介绍了骑马岭水电站砂石加工系统的料源规划、系统规划设计、系统工艺流程及环保措施。该加工系统采用的典型的二段破碎工艺，对中小型水电站混凝土骨料生产系统的设计具有一定的参考价值。同时，该加工系统在废水处理水回收利用及细砂与石粉回收、防尘、降低噪声，以及固体废弃物处置等方面，均采取了相应的环保措施，以减少其对施工人员和周围环境的影响。     

Dental amalgam – the effect of the technology of alloy powder preparation on the corrosion behaviour and the release of mercury

Dental amalgams are based on a broad spectrum of materials differing in their chemical composition, metallurgical treatment, and in the way the initial alloys powders are prepared. In addition to their chemical composition, amalgams based on various powders differ in both their microstructure and the amount of mercury needed for preparation. All these facts may affect electrochemical processes occurring during their interaction with oral fluids, and also mercury release. While verifying the effect of the technology used for the preparation of the high‐copper ternary alloy powder on the properties of resulting amalgams, this study aimed at the mechanism of their interaction with a model saliva solution as well as mercury release was included. Measurements were done in a model saliva solution using standard electrochemical methods and exposition measurements. The interaction of individual types of amalgams with artificial saliva did not reveal any significant differences. The free corrosion potential of all these amalgams in an aerated solution settled in the range of values in which tin oxidation, resulting in a layer of insoluble corrosion producsts, turned out to be the dominant anodic process. The rate of mercury release was the lowest for amalgams based on a gas‐atomized alloy. The highest rate of mercury release, and also its dependence on time, was exhibited by lathe‐cut powder based amalgam. In addition to different volume fraction of the Ag‐Hg phase and the level of its tin alloying, this different behaviour may be explained by differences in the rate at which a layer of tin corrosion products acting as a barrier to mercury release is formed.     

利用UTD修正的MoM-PO混合算法研究

介绍了利用矩量法(MoM)和物理光学(PO)混合方法处理复杂线体结构的电磁散射问题，提出利用pulse基函数对线电流进行展开，使得处理复杂线体结构问题变得简化，并推导出一般的矩阵方程。然后针对PO在阴影区域失效等问题，利用UTD(一致性几何绕射)对该简化模型结构下的PO区域电流进行了修正，使得其应用范围得到扩展、计算精度得到提高。文中的实例结果与传统的MoM很好的一致，从而说明了该方法的有效性和精确性。