制备方法对复合触头材料导电特性的影响

根据复合材料制备方法的各自特点 ,建立了计算复合触头材料电导率的三维单元网络模型。应用该模型研究了制备方法对材料电导率的影响 ,并与测量值进行了比较。结果表明了这种模型的可行性。     

激光超高温度梯度快速定向凝固研究

研究了激光重熔工艺参数对三种不同成分的Cu Mn合金重熔区微观组织生长方向的影响。结果表明 ,熔池中微观组织的生长方向强烈地受激光工艺参数 (激光输出功率和扫描速度 )和合金成分的影响。通过选择合适的工艺参数 ,实现了与Bridgman法类似的超高温度梯度快速定向凝固 ,其温度梯度可高达 10 6 K m ,速度可高达 2 4mm s。利用激光表面熔凝技术实现超高温度梯度快速定向凝固的关键在于 :1)在激光熔池内获得与激光扫描速度方向一致的温度梯度 ;2 )根据合金凝固特性选择适当的激光工艺参数以获得胞晶组织。     

Magnetic separations in biotechnology—a review

Magnetic separation technology has a broad range of potential applications in both small and large scale biotechnology. This review considers a selection of magnetic techniques and their possible uses.     

Pulsed field gradient n.m.r. measurements and theoretical interpretation of the self-diffusion of polystyrene in solution

The self-diffusion coefficients of polystyrene dissolved in C₆D₆ were measured by means of pulsed field gradient n.m.r.. The dependence on the molecular weight was of the power of -2 in accordance with the reptation model. The concentration dependence was theoretically calculated within the blob concept which shows that in the crossover region the self-diffusion coefficient is determined only by the blob dimensions and the monomeric friction coefficient is constant. The calculated concentration dependence agrees well with that observed by the authors.     

基于人工神经网络的河川径流实时预报研究

将人工神经网络技术应用于河川径流实时预报，建立起河川径流实时预报的BP网络模型，并针对经典BP算法所存在的缺陷，采用共轭梯度优化和误差反向传播训练算法，使得所建立的BP网络模型的收敛性大为改善，消除和避免了实际应用中可能出现的局部优化问题．利用西大洋水库1975～1995年的入库径流系列资料，对所建立的BP网络模型进行训练和检验，同时探讨了网络结构对网络模型预报结果的影响．通过大量的实际应用和对比分析，表明BP网络模型比HG分析模型和相关图法更优越、更具有实际推广和应用价值．     

高温用（SiC—AlN）Mo功能梯度材料的加工

讨论了热屏蔽用（SiC－AIN）／Mo功能梯度材料的粉末冶金加工。利用钼作为基体材料，以承担结构强度和连接可能性。根据在1000K温差内的完全热传递，研究了组分配置的设计，并且以最佳的组分配置成功地加工出了（SiC－AIN）／Mo功能梯度材料的烧结坯料。     

利用液晶光阀实现的光学形态变换

提出了基于液晶光阀的光学二值图像领域处理器，利用它完成了扩、蚀和边缘检测等形态变换操作，并给出了实验结果。     

梯度折射率棒中传播的高斯光束轨迹解析解及其存在条件的讨论

本文提出光束轨迹方程的一般解，导出解析解的存在条件，推广了文献［１］的光线传播理论，文中以一特定梯度折射率棒为例，讨论了高斯光束在棒中的传播特性。     

Application of SiC-Si functionally gradient material to thermoelectric energy conversion device

Because of its high–temperature chemical stability, SiC ceramic is a promising material for high-temperature device applications such as thermoelectric energy converters. However, the electrical conductivity of SiC ceramic is too low for it to be used as a thermoelectric energy converter at the cold junction. Therefore, we propose a SiC-Si functionally gradient material (FGM) in order to improve the electrical conductivity of the SiC ceramic at the cold junction. An SiC rod was fired in a temperature gradient furnace. One end of the SiC rod was maintained at 2473 K and the other end was maintained at 1973 K for 30 min. After firing, the porous SiC edge fired at 1973 K was dipped into molten Si in order to infiltrate molten Si into the porous SiC. The microstructure of the FGM is classified into three regions: the SiC-Si composite material; the porous SiC ceramic; and the densified SiC ceramic. The electrical conductivity, the Seebeck coefficient and the thermal conductivity for each region of SiC-Si FGM was measured at 300 K; a figure of merit was calculated. The figure of merit of the SiC-Si FGM at the cold junction, at room temperature, was 10⁸ times higher than that of a nongradient SiC ceramic.     

A New Variable Diffusion Drying Model for the Second Falling Rate Period of Paddy Dried in a Rapid Bin Dryer

The objectives of this article is to propose a new drying model for the second falling rate period known as the variable diffusion controlled period that follows after the first falling rate period and to propose a new method to determine the second critical moisture content that separates these two periods. Experimental work on paddy drying at minimum fluidization velocity was carried out in a rapid bin dryer. The effects of operating temperatures (60-120°C) and bed depths (2-6 cm) on the paddy drying characteristics were investigated. It was found that the normalized drying rate of paddy was proportional to the normalized moisture content in the first falling rate period but in the second falling rate period, the normalized drying rate of the material varies exponentially with the normalized moisture content. The different relationship between the normalized drying rate and the normalized moisture content in the first and second falling rate periods indicate that two different mechanism of moisture transport are at work. The new exponential model of the second falling rate period and the linear model of the first falling rate period were found to fit the experimental data very well. Derivation from variable diffusion equation shows that the linear model is the result of constant diffusion coefficient whereas the new exponential model is the result of linear diffusion coefficient. This also implies that the first falling rate period is a constant diffusion controlled period and the second falling rate period is a variable diffusion controlled period. In addition, drying kinetics data of a drying process that fits the exponential model over a very slow drying period will show that the drying process is under the effect of a linear diffusion coefficient. It was also found that the proposed new method to determine the second critical moisture content that distinguishes between the first and second falling rate periods by using a sudden change in the value of the drying rate gradient to a much lower value at that point is more rigorous and yet simpler than the method of determining the specific location of the receding drying boundary since it is based on the behavior of the actual drying kinetic data.