可编程控制器在包装机上的应用

本文介绍了可编程控制器（PLC）在包装机上的应用．介绍了系统的硬件设计与软件开发．     

海洋机器人用水下电机的深水密封研究

本文研究了海洋机器人用水下电机各个部分的密封方法，同时介绍了一个先进的动密封装置以及检验密封性能的水压试验方法．经测试及实际使用表明该密封方法和动密封装置完全满足水下机器人在深水中运行的密封要求     

红外遥感用低温制冷器的进展

低温制冷器与红外探测器配套，是军事现代化、高新技术等急需发展的关键产品。国内研制技术也已接近国际先进水平，基本掌握了小型化、低振动、长寿命、细方形漆包线制作、间隙密封、消除电磁干扰等相关关键技术。本文列出了已研制过的直线电机谐振压缩机的主要技术性能。希望主管、用户、研制、生产各方通力合作，应用－改进－再应用－再改进，实现我国低温制冷器的产业化。     

An automatic torque ripple compensation system for direct drive motors

A serious problem in motion control is the occurrence of torque ripple. Since a direct drive (DD) motor with a magnet rotor uses a rare-earth magnet, the torque ripple is more serious than that of conventional servomotors. This paper presents an auto-compensation of torque ripple using a software-implemented torque observer. The frequency and amplitude of torque ripple can be obtained in the controller by using the estimated torque from an observer, and the autonomous generation of a compensating current component for a torque ripple is possible. The proposed algorithm has been verified by experiments.     

我国车用汽油的发展概况及发展方向探讨

介绍了我国车用汽油的发展轨迹 ,通过与国外先进标准的对比分析了我国车用汽油存在的不足 .指出我国在加入WTO后 ,更应不断升级车用汽油质量标准 ,需要从标准制定、炼油技术等多方面追赶世界先进水平 ,积极研制生产清洁型无污染汽油 ,从根本上消除汽车尾气对环境的污染 .     

提高大直径井眼机械钻速的几项措施

随着我国西部地区石油勘探开发的进展，5000－7000m的深探井所钻数量不断增多，套管程序增加，特别是大尺寸井眼所钻深度明显加大。由于国产大尺寸钻头结构单一、型号少，破岩机械能量和水力能量不足，在易斜井段目前尚无可靠的防斜保直措施，以及钻井液性能不适宜等原因，大尺寸井眼的钻这远远低于215．9mm井眼的钻速。据此，提出了几项可以提高大尺寸井眼钻速的措施：增加大尺寸钻头的种类，采用阶梯式扩眼钻头，强化钻井参数和水力参数，选用中速动力钻具，改善钻井液性能以及采用冲击旋转钻具等。     

AN EXPERIMENTAL AND NUMERICAL INVESTIGATION OF THE STARTING FLOW OF A UNIFORMLY ACCELERATING CIRCULAR CYLIINDER

The starting flow around a uniformly accelerated circular cylinder is investigatedby flow visualization techncque and solving N-S equations numerically in detail.The results ofthe starting flow are similar with those of the impulsively started one.At lower Re_α,numbers the“phenomenon a”is revealed;the“phenomenon β”appears at higher Re_α numbers,but withonly one secondary vortex.At the early stage of the starting vortex formation,the flow islaminar;at the later stage,the flow transforms into turbulent flow.The velocity distribution inthe flow field is measured with the multiwires installment.The calculational results are comparedwith the results of experiment,and both are in agreement with each other.     

A sensorless brushless dc motor system

This paper describes a brushless dc motor system without position or speed sensor. The brushless motor consists of a permanent magnet synchronous motor and a voltage-source inverter capable of controlling the amplitude and frequency of voltage. The rectangular-shaped stator current with a conducting interval of 120° (electrical) is controlled to be in phase with the trapezoidal back electromotive force. This results in producing maximum torque. Variable speed is achieved by adjusting the average motor voltage similarly to chopper control of dc motors. In this paper, two sensorless position detecting methods, i.e., an “indirect method” suited for the lower-speed range and a “direct method” suited for the higher-speed range are proposed. The combination of the two makes it possible to detect the rotor position over a wide-speed range. Furthermore, a speed-sen-sorless PLL control is proposed in applying the principle of the direct method. Experimental results obtained from a prototype brushless dc motor are shown to confirm the validity of the sensorless drive. The starting procedure of the motor also is discussed because it is impossible to detect the rotor position at a standstill.     

潜油电动机滑行时间的自动测量

潜油电动机滑行时间是评定电动机装配质量的重要指标。鉴于手工测量电动机滑行时间存在效率低和误差较大的不足,设计了潜油电动机滑行时间自动测量系统。它通过分压电路和计算机自动测量系统测量潜油电动机定子上感应的电压变化状况,即可得到电动机滑行时间。用手工测量、波形分析和自动测量3种方法测量6种型号电动机的滑行时间,其中5种滑行时间长于3s,判定为合格;1种滑行时间短于3s,判定为不合格。3种方式测量的滑行时间具有较好的一致性,仅波形分析法得出的滑行时间比自动测量的滑行时间稍长,表明自动测量方法的精度和重复性可满足要求。     

同步电机转子的检修探讨

同步电动机转子时常由于磁极松动,导致电机振动现象严重.本文以烧结厂1#抽烟机转子检修为例对同步电机的转子检修进行探讨,很好的解决了这个问题.同时为同步电机转子检修提供了一整套检修方法.