反相微乳法制备纳米ZrO2前躯体溶液微观结构的研究

本文通过拟三元相图法、电导法和红外光谱法对CTAB/正己醇/环己烷/水形成的四元反相微乳液体系的微观结构进行了研究,进而确定用于制备纳米ZrO2的最佳反相微乳液体系。     

采用Raman光谱研究硅烷接枝LLDPE的结晶结构

采用傅里叶变换红外光谱(FTIR)和Raman光谱表征了硅烷接枝线型低密度聚乙烯(LLDPE)的结晶结构。用FTIR和Raman光谱上硅烷特征峰与LLDPE亚甲基峰的强度比,可相对比较硅烷接枝LLDPE的接枝率,随着硅烷用量的增加,由FTIR计算的吸光比从0.96增至2.62,由Raman光谱计算的强度比从11.53增至14．00,两者的变化趋势相同。Raman光谱分析还表明,随着硅烷用量的增加,硅烷接枝聚乙烯的结晶相质量分数由57．58％降至46．99％,非晶相质量分数由11．58％升至16．52％,中间相质量分数从30．84％升至36．48％。     

采用加压-真空两段热缩聚法制备中间相沥青炭纤维的原料

以深度裂解石油渣油为原料，采用两段热缩聚法可制得软化点为268℃，可编性良好的中间相沥青。本文详细考察了温度，时间对中间相沥青软化点，可编性，中间相沥青形态及碳化收率的影响，并初步探讨了两段热缩聚反应的机理。研究结果表明反应温度，时间对中间相沥青的结构和性能影响较大，选择适宜石油渣油，采用加压－真空两段热缩聚法，调整反应条件，可制得可纺性良好的中间相沥青。     

有机磷化物制备羟基磷灰石工艺条件的探讨

探索用有机磷化物制备羟基磷灰石的工艺条件：采用硝酸钙、氨水、磷酸三丁酯为原料进行正交对比研究，优化得到了制备较佳羟基磷灰石的工艺条件。优化的工艺条件为：原料中Ca／P（molar ratio）1．67；Ca（NO3）2、4H2O／NH3H2O（g／g）为0.99；烧结温度为850℃：恒温时间为5h，并对合成的样品进行了化学和红外光谱的分析。     

聚烯烃接枝马来酸酐接枝率的测定—聚乙烯接枝

以非均相化学接枝法和红外光谱法相结合的方法绘制了定量校正曲线,可用于红外光谱法测定聚乙烯接枝马来酸酐的接枝率。该方法简便快速,准确可靠,重复性好。     

Infrared study of salt free and salt treated cellulose pyrolysis under nitrogen atmosphere

The pyrolysis under nitrogen of salt free and salt treated cellulose was studied by infrared spectroscopy. The results confirm the unzipping mechanism suggested by DTA and TGA studies, and show this mechanism to apply to the untreated and salt treated samples. The results also show the unzipping to stop at the stage of char formation. The onset of this stage was found to occur after the volatilization of only 45–50% of the initial sample of the borax treated cellulose, compared with 65–70% of the KCl treated cellulose and 80–85% of the untreated cellulose.     

玉米芯木聚糖硫酸酯化条件的研究

用碱提法从玉米芯中提取木聚糖,采用氯磺酸吡啶法进行硫酸酯化,通过正交试验确定最佳工艺条件为:吡啶与氯磺酸摩尔比1∶1,温度65℃,时间6h;木聚糖硫酸酯wisX-S通过DEAESepharoseFF层析柱分离得到一个相对分子量为1.3×104的组分,硫酸基取代度为2.24。对此木聚糖硫酸酯进行红外光谱分析,结果显示在波数1259、1228和813cm-1处分别有S=O和C-O-S键的特征吸收峰。     

Surface and Interfacial Studies of Plasma-Modified Composite Surfaces

Model epoxy and bismaleimide compounds in thin film form were used to simulate epoxy and bismaleimide composite surfaces, in order to study compositional changes and interfacial reactions induced by oxygen plasma treatment. X-ray photoelectron spectroscopy (XPS) and infrared reflection-absorption spectroscopy (IR-RAS) were used to probe chemical changes which occurred. XPS and IR-RAS were found to be complementary techniques in determining the nature of functional groups incorporated into surfaces by plasma treatment. IR-RAS analysis of the model surfaces following exposure to a liquid epoxy resin revealed that while adsorption of the liquid epoxy occurred on both plasma-treated and nonplasma-treated surfaces, the oxygen plasma-treated surface alone was capable of initiating ring-opening reactions in the epoxy. However, this effect was not observed unless immediate contact was made between the plasma-treated surface and the liquid epoxy resin, illustrating the short-lived reactivity of the functional groups on the plasma-treated surface.     

单光源多组分红外在线分析仪设计

基于红外光谱吸收原理,设计了一种单光源单光路的在线分析仪。在实验室环境下,利用SO2进行实验,并对实验结果进行分析。实验结果表明:该分析仪具有很好的准确性、重复性和稳定性,实现了多种气体的在线测量。     

Adhesive Bonding of Oil-Contaminated Steel Substrates

Durability of adhesive bonds formed by curing epoxies against oil-contaminated steel substrates using amidoamine curing agents was determined during exposure to boiling water. The most durable bonds were obtained using amidoamine curing agents with relatively low amine numbers and by blending silane coupling agents such as γ-glycidoxypropyltrimethoxysilane (γ-GPS) and N-(2-aminoethyl)-3-aminopropyltrimethoxy silane (AAMS) into the adhesives. When X-ray photoelectron spectroscopy (XPS) was used to characterize the failure surfaces of the adhesive joints after exposure to boiling water, it was determined that adhesives prepared using amidoamine curing agents with low amine numbers were able to displace the oil from the steel surface but adhesives prepared with amidoamine curing agents with high amine numbers were not. Results obtained from XPS also showed that the amino groups on the substrate fracture surfaces of joints prepared using curing agents with low amine numbers were protonated whereas the amino groups in the bulk adhesive were not, indicating that there was a chemical interaction between the curing agent and the hydrated surface of the substrate. It was also shown using infrared spectroscopy that the amidoamine curing agents formed salts with calcium compounds in the oil.