New anti-ablation candidate for carbon/carbon composites: Preparation,composition and ablation behavior of Y2Hf2O7 coating under an oxyacetylene torch

Y₂Hf₂O₇ possesses low thermal conductivity and high melting point, which make it promising for a new anti-ablation material. For evaluating the thermal stability and the potential applications of Y₂Hf₂O₇ on anti-ablation protection of C/C composites, Y₂Hf₂O₇ ceramic powder was synthesized by solution combustion method and Y₂Hf₂O₇ coating was prepared on the surface of SiC coated C/C composites using SAPS. Results shown that the coating exhibits good ablation resistance under the heat flux of 2.4?MW/m² with the linear and mass ablation rates are 0.16?μm?s^?1 and ?0.028?mg?s^?1, respectively, after ablation for 40?s. With the prolonging of the ablation time, the increasing thermal stress causes the increase of cracks. Moreover, the chemical erosion from SiO₂ and the physical volatilization of low temperature molten products aggravate failure of the Y₂Hf₂O₇ coating.     

快速灵敏的LC-MS/MS法测定人血浆中阿莫西林并应用于两种制剂的一致性评价

目的: 建立快速灵敏的LC-MS/MS法测定人血浆中阿莫西林浓度，并用于两种阿莫西林胶囊的一致性评价。方法: 采用岛津公司LCMS-8060型LC-MS/MS仪，以MRM模式测定阿莫西林（m/z 366.00/114.00）的浓度，d4-阿莫西林作内标（m/z 370.10/114.05），离子源为ESI源。色谱柱选用Waters ACQUITY BEH C18（2.1×50 mm，1.7 μm），梯度洗脱。血浆样本加入内标，经甲醇沉淀蛋白后取上清液进样检测。结果: 所建方法经验证，其线性、准确度、精密度、最低定量限、提取回收率、特异性、基质效应、稳定性等各项指标均符合CFDA的指导原则及最新核查标准要求，并较文献报道中的方法有处理简单、灵敏度高、色谱峰形好的优点。结论: 所建方法快速、灵敏，适用于人血浆中阿莫西林浓度的检测。用于一致性评价的样本实测，两种制剂生物等效。     

Stabilizing temperature-capacitance dependence of (Sr,Pb, Bi)TiO3-Bi4Ti3O12 solutions for energy storage

(1-x)Sr_0.7Pb_0.15Bi_0.1TiO₃-xBi₄Ti₃O₁₂ ((1-x)SPBT-xBIT, x = 0-0.125) bulk ceramics were developed and calcined via the solid-state method, aimed at the application of pulsed power capacitors. The phase structures, temperature stability, hysteresis loop, and discharge properties were systematically investigated. Considering both the temperature stability and dielectric properties, 0.925SPBT-0.075BIT bulk ceramics with a capacitance variation satisfying the X7R specification were developed for pulsed power capacitors. The energy storage density was 0.252 J/cm³, and the ceramics showed high temperature stability at 80 kV/cm. The discharge current waveforms of the 0.925SPBT-0.075BIT ceramics were recorded. A high discharge power density of approximately 1.01 × 10⁸ W/kg with an 8 Ω load resistor and short discharge period of 84 ns were achieved at 50 kV/cm. The good temperature stability properties and high power density show that the 0.925SPBT-0.075BIT ceramics are well suited for pulsed power capacitors with a wide temperature range.     

Preparation of nanocrystalline nickel oxide from nickel hydroxide using spark plasma sintering and inverse Hall-Petch related densification

Nanocrystalline nickel oxide (NiO) was prepared from nickel hydroxide by Spark plasma sintering (SPS) and the mechanisms involved in the densification of NiO were studied. Reverse precipitated nickel hydroxide powders were SPS processed at 400, 600 and 700?°C with 70?MPa pressure. Pure NiO with 12?nm crystallite size formed after 400?°C sintering process. However NiO grains had grown to 18 and 38?nm after 600 and 700?°C sintering respectively. NiO pellets prepared using 600 and 700?°C SPS sintering schedules had relative densities of 83% and 94% respectively. Two displacement rate regimes were observed during densification of NiO in both 600 and 700?°C sintering processes. Decomposition of nickel hydroxide and particle sliding of NiO led to first displacement rate maximum while inverse Hall-Petch based plastic deformation facilitated densification during the constant second displacement rate regime. No densification occurred during sintering holding times indicating the limited role that diffusion played during densification.     

计量用脉冲Nd：YAG倍频激光器及其电源

介绍了脉冲Nd:YAG倍频激光器双波长（1064／532nm）3种输出的激光光路。1064nm输出的动静比可达0.40；KTP晶体外腔倍频效率可达0.50。介绍了稳定可靠的调Q电路、逻辑控制电路和开关电源的主电路及其参数计算。     

BaTiO3基Au纳米颗粒复合薄膜的制备及其光学性质研究

采用溶胶-凝胶（sol-gel）方法，成功的将高体积面分比的Au纳米颗粒复合到BaTiO3的非晶薄膜中，并对其光学性质进行了研究。用XRD、TEM、椭偏仪、吸收光谱、光克尔效应OKE（Optical Kerr Effcet）方法对薄膜进行了表征和测试。从吸收光谱观察到表面等离子体共振SPR（Surface Plasma Resonance)峰随热处理温度升高而红移的现象。光学非线性测试表明薄膜具有高的三阶非线性极化率Χ^(3)和超快的响应时间。     

等离子体刻蚀工艺控制模型分析

讨论了主因素分析法以及神经网络法在等离子体刻蚀工艺中的应用.结果表明主元素分析法可以实现对数据的压缩,而神经网络算法则显示出比传统的统计过程控制算法更好的准确性.     

磁电雾化电晕放电低温等离子体及其应用

本文讨论了磁电雾化电晕放电低温等离子体技术的基本原理,以及它在静电除尘、烟气脱硫等环保生物工程等领域中的应用前景.