Reliability analysis on systems with self-healing and self-repairing under different environments and shock models

Inspired by the process of self-healing of biological damage, high technology materials with self-healing and self-repairing mechanisms have been developed for high reliability and long lifetime. Therefore, the reliability modeling on intelligent systems with healing performance has become a research hotspot. Based on the diversity of healing mechanisms, this paper proposes a two-phase reliability model method on self-healing and self-repairing systems. Impacts of environments, shock loads, self-healing, and self-repairing mechanisms are taken into account in this novel model. Besides, system lifetime and some reliability indexes under two shock models are derived, respectively. Moreover, Monte Carlo simulations are conducted to verify the accuracy of reliability under two models. Finally, an engineering case of metallized film capacitor is provided to illustrate the effectiveness and applicability of the proposed models by comparing numerical results and simulation results.     

基于激光点云数据的叶片型面三维重构

在四坐标叶片型面检测基础上,提出基于激光点云数据的叶片型面三维重构方法。激光位移传感器对叶片型面进行多视角扫描采样,快速采集叶片型面海量点云数据。运用由点到线到面的数学建模原理,先基于端点一阶导矢连续法拟合出光顺NURBS曲线,再依据分片能量法构建辅助曲面拟合出光顺NURBS曲面,最后对分片NURBS曲面进行统一描述,构造出精确光滑的叶片型面,实现叶片型面的三维重构。实验结果表明：采用该方法实现对各类叶片复杂型面的三维重构,重构误差均<0.015 mm,能够满足精密零件的测量需求。     

小水电综合参数微机监测系统的研制

介绍了一种分布式小水电综合参数微机监测系统．该系统运用多台８０Ｃ１９６单片机系统组成的远动柜对现场多种被测信号进行采集,运用多台微机组成的局域网络对远动装置传送来的数据进行计数、处理、显示、打印、入库等操作,从而使系统完成对小水电各种参数的监测功能．     

智能铸砂发气性能试验机高温监控研究

本文分析了影响智能铸砂发气性能试验机高温控制精度的主要原因, 并详细介绍了提高高温控制精度的一些有效措施     

利用单片机控制的步进电机系统

本文介绍了几种常见的利用单片机控制步进电机的原理及方法,并对各种方法加以比较分析,指出了各自的特点.     

用BASIC单片机实现油品密度的测量

油品的密度与温度有着确定的对应关系,通过测量温度可以间接测量密度。根据这一关系可以利用小巧的ＢＡＳＩＣ单片机设计一个价廉、实用的密度计。经实验对比,其稳定性较好,反应灵敏,测量较准确,较常规方法更方便快捷     

从测角后交最佳点位规律看规范规定之不足

本文分析了文献[1]所总结的测角后交两类公式在取得最佳点位时的规律,指出当前规范对此问题规定之不足.     

Influence of ions on the critical behavior of a binary mixture near the consolute point

The lower critical point of stratification of a 3-methylpyridine (MP)+heavy water (D₂O) mixture in the presence of Na⁺ and CI^– ions has been studied by the Toepler shadow method. Addition of 0.3% ions lowered the critical temperature and reduced the equilibration time and the gradient of the refractive index (compressibillity). The analysis of the form of the near-critical isotherm demonstrated the ionic mixture to be described by the index = 3.05 ± 0.15. which corresponds to the classical mean-field theory. The results obtained provide evidence that even small admixtures of charged particles result in a substantial suppression of fluctuations near the critical point by the long-range Coulomb interaction.Paper presented at the Twelfth Symposium on Thermophysical Properties, June 19–24, 1994, Boulder, Colorado, U.S.A.     

Melting and Vaporization of the 1223 Phase in the System (Tl-Pb-Ba-Sr-Ca-Cu-O)

The melting and vaporization of the 1223 [(Tl,Pb):(Ba,Sr):Ca:Cu] oxide phase in the system (Tl-Pb-Ba-Sr-Ca-Cu-O) have been investigated using a combination of dynamic methods (differential thermal analysis, thermogravimetry, effusion) and post-quenching characterization techniques (powder x-ray diffraction, scanning electron microscopy, energy dispersive x-ray spectrometry). Vaporization rates, thermal events, and melt compositions were followed as a function of thallia loss from a 1223 stoichiometry. Melting and vaporization equilibria of the 1223 phase are complex, with as many as seven phases participating simultaneously. At a total pressure of 0.1 MPa the 1223 phase was found to melt completely at (980 ± 5) °C in oxygen, at a thallia partial pressure (p_Tl2O) of (4.6 ± 0.5) kPa, where the quoted uncertainties are standard uncertainties, i.e., 1 estimated standard deviation. The melting reaction involves five other solids and a liquid, nominally as follows: 1223→1212+(Ca,Sr)2CuO3+(Sr,Ca)CuO2+BaPbO3+(Ca,Sr)O+LiquidStoichiometries of the participating phases have been determined from microchemical analysis, and substantial elemental substitution on the 1212 and 1223 crystallographic sites is indicated. The 1223 phase occurs in equilibrium with liquids from its melting point down to at least 935 °C. The composition of the lowest melting liquid detected for the bulk compositions of this study has been measured using microchemical analysis. Applications to the processing of superconducting wires and tapes are discussed.