Resilient metal spring network silicone-matrix composite for separable interconnections

Resilient metal spring silicone-matrix conducting composites for separable interconnections in electronics were fabricated by the impregnation of silicone into a preform comprising randomly oriented C-shaped Cu-Be springs and a small proportion of Sn-Pb solder, which served to connect the springs at some of their intersections. Composites containing 6.1-9.8 vol.% total filler exhibited volume electrical resistivity 0.5-1.0 mΩ.cm and contact resistivity (with copper) 11-17 mΩ.cm². A compressive stress of about 30 kPa was needed for the low contact resistivity to be reached. The volume 17-26% and the contact resistivity increased by 5% after heating in air at 130-150°C for seven days. Composites containing <9 vol.% total filler showed no stress relaxation for seven days at 6.0% strain.     

基于PRO/E三维管道轨迹专用检具的设计

介绍使用该软件组件设计模块中的高级工具———切除 (CutOut)功能设计高精度三维轨迹管道零件检具的方法 ,该方法具有高效和精密等特点。     

面板坝垂直缝失效渗流场有限元模拟

以班多面板堆石坝为例,用有限元方法计算了当面板缝局部失效时各种工况下的渗流场,系统分析了大坝在面板垂直缝局部失效后的稳定渗流场的规律和特点。通过分析计算结果,指出了面板缝的失效位置、失效缝宽、失效缝长以及垫层的渗透系数对等势线和浸润线的影响,并且对面板、垫层和接缝的设计提出建议。     

连续多跨大柱距空旷厂房的空间结构设计

以鞍钢大型厂房改造工程为例,介绍了一种打破常规的空间设计方法,并阐述了大跨度吊车桁架支座、节点等重要传力部位的构造形式及其利弊,可供同类工业厂房改造工程设计时参考。     

Three-dimensional stability analysis of the dam foundation at Baise

It is usually difficult to determine the actual safety factors of rock masses in an ordinary two-dimensional stability analysis if the safety factors of the different cross sections in the rock mass vary significantly. In addition to the actual slope, arch dam abutment, and the actual foundation of a high building, another example is that the different cross sections of the foundation in the monolith of a gravity dam vary significantly, just like the condition at the overflow dam in the Baise project. A three-dimensional stability analysis method based on the upper-bound theorem was employed to solve this problem. The parameters used in the analysis were obtained from geomechanics tests, as well as continuity simulations of the randomly distributed joints. Two failure patterns against sliding are analyzed. One pattern is the foundation slide along deep-seated planes which were determined by calculations. The other pattern is the foundation slide along the planes across the bottom of the high steps in the foundation pit. The results indicate that a special overflow dam monolith can be considered to be safe in case of considering the three dimensional effect. However, a key wall with a depth of 5m must be constructed at the upper side of this monolith in order to ensure the safety of the foundation. Translated from Chinese Journal of Rock Mechanics and Engineering, 2006, 25(3): 533–538 [译自: 岩土力学与工程学报]     

非饱和土二、三维固结方程简化计算方法

针对非饱和土的固结问题的复杂性,为了计算的简化,将非饱和土固结分为3个阶段:初期压密、气压消散和水压消散。假定前两个阶段是瞬间完成的,其后独立考虑水压的消散。分别建立3个阶段的二、三维控制方程,以计算各阶段的气压、水压、骨架应力、相应的土体变形和水量变化。算例的计算结果表明本文方法简便、实用。该简化方法主要适用于饱和度不太高的非饱和土,而对饱和度较高的非饱和土,由于气压消散过程较长,不宜采用。     

激光雷达在装甲车中的应用探讨

探讨了激光雷达的特性、工作原理以及相对于微波雷达的优势，并提出了现在乃至将来激光雷达作为现行装甲车辆传感器的重要补充手段，在高精度跟踪测量、高分辨率目标识别和三维成像等方面的应用前景，并论述了激光雷达存在的缺点和改进方法。     

三元复合驱波及系数和驱油效率的实验研究

为了搞清三元复合体系提高采收率的机理,通过室内三维物理模拟驱油实验研究了非均质砂岩油田三元复合驱油过程中波及系数与驱油效率的变化特征,量化三元复合驱不同类型储层驱油效率和波及系数对提高采收率的贡献程度.结果表明,在有隔层的条件下,中渗透层贡献程度达到了25.29%,其次是低渗透层,贡献率为44.31%,而高渗透层仅为30.40%;分析认为,三元复合驱的主要作用在于提高驱油效率,而且主要是提高高渗透层的驱油效率,同时能够提高中低渗透层的波及系数.初步得出驱油效率对提高采收率值的贡献率为33.27%,波及系数的贡献率为66.73%.     

三维目标旋转畸变不变光学相关滤波器组的设计

研究了三维目标旋转畸变不变光学相关滤波器组的设计原理，完成了滤波器组参数的计算和编码，以及光学相关识别的计算机模拟。     

崇拜与征服──试论两性服装

男装和女装的区分，从根本上说，源于人类两性社会学意义上的分离，男女装的形成与发展，从一个侧面反映了人类文明进程中性别尊卑这一社会伦理观念的演化，成为一系列服装文化现象诸如服饰动机、审美标准的依据。并在普遍的意义上，揭示了服装观念的基本原则和规律．