水性环氧煤沥青防腐涂料的配方设计及施工

阐述了环氧煤沥青防腐涂料的一些性能特点,分析了水性环氧煤沥青涂料的配方设计、性能影响因素、简单配方及生产工艺,介绍了水性环氧煤沥青防腐涂料的施工工艺。     

Study of the mineral and phase composition of aluminosilicate refractory ShPD<Subscript>M</Subscript>-45 after service in an aluminum electrolyzer of OAO Zaporozh’e aluminum combine

Comprehensive studies have established that ShPD_M-45 refractory produced by OAO Zaporozhogneupor exhibits good anticorrosion properties towards the action of electrolysis bath corrosive extraneous components. The degree of degradation of ShPD_M-45 refractory after two years of service is 10%. The average concentration of entry of Na_g and F_tot into ShPD_M-45 refractory through hearth blocks with 50% graphite is correspondingly 4.08 × 10^–4 and 3.32 × 10^–4 g-mole/day. It is established that ShPD_M-45 refractory is a more reliable barrier material than unmolded aluminosilicate mixes. The penetration rate of corrosive components of the electrolysis bath into unmolded aluminosilicate materials is greater by a factor of 10 – 30 than for ShPD_M-45 refractory. It is shown that the protective function of titanium-containing components and glass phase in an electrolyzer lining develops as a result of forming fluoride, subfluoride and oxyfluoride titanium compounds. Industrial approval of ShPD_M-45 refractory under OAO Zaporozhe Aluminum Combine conditions has shown that it exhibits good operating properties in electrolyzers with hearth blocks with 50% graphite The authors thank D. V. Pruttskov and D. Yu. Boguslavskii for help with this work. Translated from Novye Ogneupory, No. 3, pp. 45 – 50, March 2009.     

Effect of gamma radiolysis on pit initiation of zircaloy-2 in water containing sea salt

In spent fuel pools at the Fukushima Daiichi Nuclear Power Station (1F), seawater was injected for cooling purposes after the tsunami disaster in March 2011. It is well known that the chloride in the seawater has the potential to cause localized corrosion (e.g., pitting corrosion) in metals. In this study, we evaluated the pitting potentials of zircaloy-2, the material used in the fuel cladding tubes in 1F, as a function of chloride concentration. To accomplish this, we used artificial seawater under gamma-ray irradiation and investigated the effect of radiolysis on pit initiation of zircaloy-2 in water containing sea salt. Changes in the composition of water containing sea salt were analyzed as well, both before and after gamma-ray irradiation. The characteristics of the resultant oxide films formed on zircaloy-2 were evaluated by X-ray photoelectron spectroscopy and electrochemical impedance spectroscopy. The experimental results showed that the pitting potential under irradiation was slightly higher than that under conditions in which no radiation was present, and that the pitting potential decreased with increasing chloride concentration in the presence as well as the absence of radiation. Solution analyses for water containing sea salt showed that hydrogen peroxide was generated by irradiation. The oxide film was composed of zirconium oxide and was made thicker during the irradiation. The higher pitting potential could thus be explained by the capacity of hydrogen peroxide to oxidize the surface and enhance oxide film formation. Under gamma-ray irradiation, the zircaloy-2 surface with an oxide film formed by radiolysis products was found to be resistant to pitting in the presence of chloride.     

Robust superhydrophobic/superoleophilic sponge for efficient removal of oils from corrosive aqueous solutions

Separation of oil/water mixtures became a significant worldwide issue because of the frequent oil leakage incidents in marine. Herein, a robust superhydrophobic/superoleophilic porous polyurethane (PU) sponge was fabricated just by simple one-step procedure of dip-coating of OTS. The modified PU sponges possessed a superhydrophobicity with water contact angles (CAs) exceeding 156°. The as-prepared sponge exhibited high oil adsorption capacity, robust recyclability for oil/water separation even under strong acid, alkali and salt conditions. Furthermore, when the as-prepared sponge was connected to a vacuum system, the sponge could efficiently remove up to 100?mL kerosene within 25?s under a vacuum of 30?kPa. The simple fabrication process and favorable durability make the sponge a promising candidate for using in a large-scale marine oil leakage clean-up.     

Electrochemical noise (EN) technique: review of recent practical applications to corrosion electrochemistry research

The ability to analyze different electrochemical corrosion phenomena, in–situ, without requiring any form of electrode perturbation has strongly attracted the attention of corrosion researchers towards the application of electrochemical noise (EN) analysis method. With the ability to analyze stochastic and chaotic electrode potential and current fluctuations at E_OCP, the EN analysis method is capable of providing information about the kinetics and mechanism of metallic corrosion with accuracy that can match conventional electrochemical techniques. Herein, we review the recent applications of EN analysis method to electrochemical corrosion research. We discuss briefly the theory behind the measurement of EN, and then highlight some of its application in the evaluation of corrosion inhibitors, pitting corrosion, coatings on metals, microbiologically–induced corrosion, as well as CO₂–corrosion. The drawbacks of the EN analysis method have also been highlighted and future considerations on the use of this important electrochemical technique have also been proposed.     

模拟地面集输环境下温度对2205双相钢均匀腐蚀及点蚀行为的影响

针对油气集输管线在CO2和含高浓度的Cl-地层水环境中易发生腐蚀失效的问题,通过腐蚀失重试验和电化学测试分析,研究了2205双相不锈钢在高分压CO2+高矿化度+高浓度Cl-地层水集输管线环境中的腐蚀行为。结果表明:在模拟油田集输管线环境中,升温引起的2205双相不锈钢的均匀腐蚀速率基本不变,整体表现为轻度腐蚀,但由于Cl-的存在,2205双相钢在50 ℃和70 ℃时出现明显的点蚀坑形貌;2205双相钢在3种测试温度下的阳极极化曲线存在明显的钝化区,随着温度的升高,2205双相钢的点蚀电位先升高、再下降,在30~50 ℃,存在一个临界点蚀温度CPT;交流阻抗图谱在50 ℃和70 ℃分别表现出了点蚀诱导期和点蚀发展期的特征。     

纯铝1060在中国南沙群岛严酷海洋大气中的腐蚀以及点蚀行为

通过质量损失测量、扫描电子显微术、能谱分析、X射线光电子能谱和电化学阻抗谱等技术研究纯铝1060在南沙群岛海洋大气环境中暴露34个月后的腐蚀行为以及点蚀行为.结果表明,在纯铝表面发生严重的点蚀,并且暴露13个月后的平均腐蚀速率达到1.28 g/(m2·a).X射线光电子能谱的测试结果表明主要的腐蚀产物为Al2O3、Al...     

合金元素对铝合金在泰国曼谷地区初期腐蚀行为的影响

在泰国曼谷地区对5083、6063和7020 3种铝合金进行为期1 a的暴晒实验,采用SEM、电化学实验、XPS和扫描Kelvin探针显微镜(SKPFM)对3种铝合金初期腐蚀形貌及腐蚀机理进行研究。结果表明:6063铝合金中Mg、Si、Fe等合金元素含量较少,腐蚀电位相对较高,约为-0.66 V (vs SCE),腐蚀产物膜较为致密,耐蚀性较好,在泰国曼谷地区的腐蚀速率约为0.7 g/(m^2·a)。7020铝合金含有较多Mg、Zn等合金元素,腐蚀电位约为-0.78 V (vs SCE),腐蚀最为严重,腐蚀速率约为3.26 g/(m^2·a)。3种铝合金均含有Mn、Si、Fe等合金元素,从而形成Fe-Si-Al或Fe-Si(Mn)-Al第二相,第二相表面电位高于基体225~280 mV,在大气环境中第二相作为阴极相,周围的基体Al优先溶解脱落,成为点蚀坑。     

Seismic life-cycle cost analysis of ageing highway bridges under chloride exposure conditions: modelling and recommendations

Chloride-induced corrosion of highway bridges constitutes a critical form of environmental deterioration and may result in significant escalation of seismic life-cycle costs due to increased fragility during earthquake events. Most of existing literature tends to adopt simplistic uniform area loss assumptions in lieu of potentially complex, yet realistic and more detrimental, pitting corrosion models for seismic vulnerability analysis. Since the degree of deterioration depends on the severity and duration of exposure, there exists a need to investigate the influence of uniform vs. pitting corrosion assumption on seismic life-cycle costs for varied chloride exposure conditions. A case-study example of a highway bridge in Central and Southeastern US reveals consideration of pitting corrosion as critical for extreme exposures compared to relatively minor settings. Subsequently this study provides recommendations to aid bridge engineers and stakeholders to balance between computational cost and accuracy of results to aid prompt decisions on rehabilitation of ageing bridges in different exposure conditions. A framework is also included to compute seismic life-cycle costs from generic measures of corrosion, independent of assumed exposure scenario. This framework is particularly helpful for seismic loss assessment of highway bridges in chloride exposure zones with periodic field measurements to estimate the extent of structural deterioration.     

Effect of microstructural features on the corrosion behavior of severely deformed Al–Mg–Si alloy

The aim of this study was to determine the influence of severe plastic deformation processing and the changes in microstructure resulting therefrom on the corrosion resistance of an Al–Mg–Si alloy. The alloy was processed using incremental equal channel angular pressing, which caused a reduction in grain size from 15 to 0.9 µm. The grain refinement was accompanied by an increase in the number of grain boundaries and dislocations, and by changes in grain orientation. However, there was no change in the size and number of intermetallic particles, which presumably resulted in a constant number of galvanic couplings. Electrochemical experiments revealed only slight differences between the samples before and after processing. Higher potential transients/oscillations upon immersion and increased corrosion currents in the vicinity of corrosion potential point to slightly higher reactivity of the most refined material. This indicates that intermetallic particles are the most crucial microstructural elements in terms of corrosion resistance. Their impact exceeds that of grain boundaries, in particular, at the stage of corrosion initiation. The development of corrosion attack is controlled more by the microstructure of the matrix as the grain refinement resulted in a less pronounced corrosion attack in comparison with the coarse-grained sample.