Surface Position-Resolved Thermophysical Properties for Metallic Alloys

Thermophysical properties are collective measures of a material to transport dynamical quantities of physical nature on its surface or through the bulk. As such, the exact nature of couplings between particles in a many-body assembly of building block atoms or molecules sensitively determines their values. The couplings between nearest neighbors are the product of the local elemental composition and the material phase. In this study, thermal cycling of a four-element Wood’s alloy specimen brings out cadmium-rich patches to the top surface of the specimen. An assembly of such patches leads to depth-dependent deviations of elemental composition from that of the bulk. Surface-layer atoms are driven to form a high temperature laser-produced plasma (LPP), and time-resolved spectroscopy of their emissions show the variability of elemental composition over surface positions as well as over depth from the surface. These thermal history-driven composition anomalies contribute to significant variability in the measured values of spectral emissivity and thermal diffusivity.     

镁合金表面喷铝防腐蚀层的微观组织分析

在AZ91D镁合金表面热喷铝，用以提高其表面的耐腐蚀性能。采用SEM，EPMA等方法对AZ91D表面喷铝扩散层的组织进行了仔细的观察与分析，发现在防腐蚀层上有大量的Mg17Al12相存在，且呈决状及非连续片状分布。经显微硬度测定，喷铝层硬度较镁合金基体高；腐蚀后这种相凸出于基体，比镁合金基体有较好的耐腐蚀性能。     

6063铝合金型材挤压"堵模"的成因及其对策

从6063铝合金铸锭、挤压工艺条件、模具、金属的不均匀变形等方面分析型材挤压时发生“堵模”现象的原因；提出了其防止措施。     

TiO_2纤维的制备、表征及其光催化活性

采用常压乙二醇法制备出在可见光下具有较高催化活性的TiO2纤维。扫描电子显微镜表征结果表明,TiO2纤维直径为0.8～2.0μm、长度为5～25μm;BET比表面积和X射线衍射表征结果表明,随焙烧温度的升高,比表面积减小,TiO2纤维晶型逐渐由锐钛矿型向金红石型转变;紫外-可见漫反射光谱分析结果表明,TiO2纤维在可见光区有明显的吸收。在可见光下对甲基橙和苯酚的降解实验表明,焙烧温度为400℃时TiO2纤维的催化活性最好,对甲基橙和苯酚的降解率分别达到90.3%和84.0%;所制备的TiO2纤维比溶胶-凝胶法制备的锐钛矿型TiO2在可见光下具有更好的催化活性,原因是其能带间隙减小和吸收波长扩展到可见光区所致。     

Models for the formation of poly(butylene terephthalate): effect of water on the kinetics of the titanium tetrabutylate-catalysed reactions: 3

In an effort to investigate the mechanism of catalysis of titanium tetrabutoxide on the polycondensation of poly(butylene terephthalate), alcoholysis and hydrolysis reactions were studied with the aid of model molecules. The retarding effect of water has also been taken into account. Appropriate kinetic equations are derived and discussed and the results compared with experimental data obtained at different molar ratios of reactants.     

B2O3/TiO2-ZrO2催化剂上环己酮肟的气相Beckmann重排反应

用共沉淀法制备了TiO2-ZrO2复合氧化物载体，BET，DTA，XRD表征结果表明，该复合载体具有较大的比表面和较好的热稳定性，对于环己酮肟气相Beckmann重排反应制己内酰胺，用复合载体制备的B2O3／TiO2-ZrO2催化剂，比分别以TiO2,ZrO2为载体所制备的B2O3/TiO2和B2O3／ZrO2催化剂具有更高的活性和选择性，实验表明，催化剂表面中等强度的酸位是环己酮肟气相Beckmann重排反应的有效活性中心。     

Corrosion Behavior of a Sputtered K38G Nanocrystalline Coating with a Solid NaCl Deposit in Wet Oxygen at 600 to 700°C

A nanocrystalline coating of K38G alloy was obtained by means of magnetron sputtering. The corrosion behavior of cast K38G alloy and its sputtered nanocrystalline coating with a solid NaCl deposit in dry air or wet oxygen at 600 and 700°C have been studied and compared. The results indicated that the mass gain of the coating is higher than that of the cast alloy at 600 and 700°C. Therefore, nanocrystallization reduced the corrosion resistance at these temperatures. Furthermore, the mass gains of the coating and the cast alloy with a NaCl deposit in wet oxygen were less than that with a NaCl deposit in dry air. The relevant corrosion mechanisms are discussed.     

非化学计量LaNi5型储氢合金的性能

采用富La混合稀土与Ni、Co、Mg等元素组合，获得了一种非化学计量LaNi5型储氢合金、用金相、XRD和SEM-EDX等方法分析了该合金的组织结构，研究了合金的气相储氢特性以及电化学性能，结果表明：在1.6MPa氢压和温度29℃下，该合金的储氢量达到1.58%（质量分数），该合金的放电容量为380mAh/g。经300次循环后容量保持率为55%，该合金的基体是CaCu5型结构的LaNi5相，但有第二相（LaMg)Ni3析出，这种第二相的形成是导致该合金大容量的关键。     

表面电沉积合金层提高碳钢齿轮的接触疲劳强度研究

 接触疲劳破坏是齿轮的主要失效形式之一． 在45#钢齿轮齿面电沉积Ni-P-Co合金层，可以显著提高其接触疲劳强度．同时，对合金层的表面形貌，表面粗糙度、显微硬度和疲劳点蚀坑形貌特征等进行了分析．