Detector physics and simulation of resistive plate chambers

We present a simulation model suited to study efficiency, timing and pulse-height spectra of Resistive Plate Chambers. After discussing the details of primary ionisation, avalanche multiplication, signal induction and frontend electronics, we apply the model to timing RPCs with time resolution down to 50 ps and trigger RPCs with time resolution of about 1 ns.     

含水汽凝析气体系相态仿真模拟研究

凝析气藏中的水汽对凝析气体系相态变化有影响。在地层中等温降压时，含水汽的烃类体系会发生反凝析现象。在反凝析现象中会产生凝析水和凝析油。这些反凝析液的聚集效应会造成凝析气井的产能严重损失。这就使得控制反凝析液的析出成为提高凝折气藏采收率的关键。在研究中，总结了含水汽凝析气体系的相态特征。同时，在对某含水汽凝析气体系相态实验分析的基础上，对该体系分考虑水汽和不考虑水汽2种情况进行相态仿真模拟。模拟结果大致与实验观测值一致。     

光电对抗仿真试验系统综述

论述了研制光电对抗仿真试验系统建设的目的和意义,光电武器系统的现状和发展趋势,介绍了光电对抗仿真试验系统的一般组成,给出了光电武器系统的常规试验内容和试验流程,并论述了可能采用的试验方法。     

HLA仿真系统因果追溯性设计

随着仿真系统变得日益复杂，基于仿真数据人为的进行因果追溯已经变得越来越凼难，所以必须对原有的仿真系统进行因果追溯性设计，使自动或半自动追溯凶果成为可能。为此，首先确定了因果关系追溯的整体思路，然后面对普遍使用的高层体系结构HLA分印仿直系统，深入分析对象类和交互类两类交互数据以及交互特点，井详细划分行为事件及因果关系类型；对HLA仿真系统中关键的联邦对象模型FOM以及仿真器进行扩展设计，从而实现系统的因果追溯性，为仿真因果追溯分析提供必要的数据。最后提出保证因果追溯需要注意的几项设计原则，并对设计所能够支持的应用做出展望。     

Nonstationary Simulation Model of Absorber with Falling Film of Suspension

A nonstationary model of SO₂ absorption from a gas phase to a countercurrent falling film of absorbing slurry was developed. Laminar, wavy and turbulent film structures were considered based on published information. Resistances to the mass transfer on the gas and the liquid sides of the interphase were considered, together with chemical reactions in the liquid phase. Relevant chemical equilibria in the liquid phase were modeled. Original experimental data on the neutralization reagent dissolution rate presented as a polydispersed two‐phase system of solids and on the rate of dissolved sulfite oxidation were used. The model was verified with experimental data from a laboratory‐scale falling‐film absorber using a single vertical tube under various geometrical and operating conditions, and a very good agreement was found with the experiment. Parametric sensitivity analysis showed the critical parts of the model.     

用MATLAB进行三相交-交变频电源的仿真设计

三相交－交变频电源在低频拖动控制中有广泛的应用，通过晶闸管设计的静止式变频电源具有效率高，无噪声的优点，但却存在设计复杂、成本高，高速困难等缺点，而利用MATLAB软件中的Simlink仿真工具来实现三相交－交变频电源的仿真设计和分析，能做到省时，省成本，易于操作，在静止式变频电源设计中有很好的使用价值。采用MATLAB仿真工具完成了一个全数字控制的三相交－交变频电源的设计。     

监控系统协议仿真研究

通过分析监控系统的通讯协议,提出了利用计算机进行协议仿真,以串行接口为例给出一个通用的协议仿真软件,并介绍了若干个应用实例.     

LARGE EDDY SIMULATION OF VERTICAL JET IMPINGEMENT WITH A FREE SURFACE

1. INTRODUCTION When wastewater is discharged into rivers, lakes or oceans, it usually leads to the formulation of turbulent jet with a free surface. If the ambient water depth is shallow, the jet will impinge on the water surface and the confinement of f…     

基于排队模型的软件性能测试框架研究

基于排队模型的仿真建模技术，提出了一种新的性能测试框架。针对该框架，提出了一种仿真模型参数估计算法。从而能在少量真实测试数据的基础上，根据业务需求产生大量具有代表性的仿真数据。该框架在北京市政交通一卡通工程总中心结算系统性能测试中得到了应用。     

TCP Performance in Optical Packet-switched Networks

Optical packet assembly is a key function to support inter-working between TCP/IP networks and optical packet-switched networks. It is characterized by the assembly delay and by the segment aggregation needed to form an optical packet. These counter-balancing aspects depend on several environment variables, such as the TCP parameters, the access link speed, the optical packet size whose effects are studied in this paper. Performance evaluations are obtained by extensive simulations in terms of send rate of TCP flows, fairness, efficiency, and assembly delay. Some guidelines in the design of optical packets that take into account the results presented are given.