全文获取类型
收费全文 | 98篇 |
免费 | 3篇 |
专业分类
综合类 | 13篇 |
化学工业 | 26篇 |
金属工艺 | 6篇 |
建筑科学 | 11篇 |
矿业工程 | 36篇 |
轻工业 | 1篇 |
石油天然气 | 2篇 |
一般工业技术 | 2篇 |
冶金工业 | 4篇 |
出版年
2024年 | 1篇 |
2023年 | 2篇 |
2022年 | 8篇 |
2021年 | 3篇 |
2020年 | 1篇 |
2019年 | 6篇 |
2018年 | 9篇 |
2017年 | 3篇 |
2016年 | 4篇 |
2015年 | 6篇 |
2014年 | 12篇 |
2013年 | 8篇 |
2012年 | 6篇 |
2011年 | 1篇 |
2009年 | 4篇 |
2008年 | 2篇 |
2007年 | 1篇 |
2006年 | 4篇 |
2005年 | 3篇 |
2004年 | 1篇 |
1997年 | 2篇 |
1996年 | 1篇 |
1994年 | 1篇 |
1993年 | 5篇 |
1992年 | 7篇 |
排序方式: 共有101条查询结果,搜索用时 19 毫秒
11.
低温混凝土抗冻临界强度影响因素的研究 总被引:3,自引:4,他引:3
目的针对低温条件下东北地区冬季施工特征,研究不同养护制度、水灰比、龄期对普通C30混凝土幼龄期抗压强度以及幼龄期抗冻临界强度的影响.方法采用一次冻结法,在-20℃的条件下养护7d。以混凝土在后期继续标准养护条件下强度增长的百分率(95%)作为评价标准.结果得出不同养护温度条件下混凝土的幼龄期抗压强度,以及标准养护条件下表干状态与表面浸润状态下混凝土的抗冻临界强度.结论水灰比在0.4~0.6的范围内,随着水灰比的增大,表干状态混凝土达到抗冻临界强度的时间由12h增加到26h,浸润状态混凝土达到抗冻临界强度的时间由36h增加到70h,而且在冬季施工低温环境中浸润状态混凝土所需的抗冻临界强度为8.5~9MPa,远大于表干状态混凝土的抗冻临界强度2、5~3MP。 相似文献
12.
A special experiment setup was designed to observe the interaction between bubbles and particle in flotation cell and to analyze the bubble characteristics such as bubble size, distribution and bubble-loading efficiency. Bubbles in water-gas system and three-phase system were measured. The results indicate that with the current setup the bubbles as small as 10μm can be easily distinguished. The average size of the bubbles generated under the given conditions in two-phase system is 410μm at frother concentration of 0. 004%, which is in good correspondence with the results of other works. The effect of frother on bubble size was probed. Increasing frother concentration from 0 to 0. 004% causes a reduction of bubble size from 700 to 400μm. The bubble loading efficiency was reported. The result indicates that the fine particle is more easily entrapped than the coarse particle. Some factors, which have effect on measurement accuracy were discussed. The aeration speed has a significant effect on the accuracy of results, if it surpasses 30 mL/s, and the image becomes unclear due to the entrapment of fine particle. Another factor, which can affect observing results, is the sampling position. At a wrong sampling position, the images become unclear. 相似文献
13.
14.
15.
站场螺旋焊管环焊缝接头失效原因分析 总被引:1,自引:0,他引:1
通过化学成分、微观组织、断口形貌分析等方法对某管线站场建设中螺旋焊管环焊接头裂纹产生的原因进行了研究。结果表明,裂纹出现于打底焊缝根焊区域,呈现出沿晶+穿晶的开裂形貌,属于焊接冷裂纹。打底焊单面焊双面成形根焊的焊瘤处附近存在未熔合缺陷是裂纹产生的直接原因,焊接工艺不当,中间焊接热输入量过大,导致粗大的粒状贝氏体形成是裂纹扩展的直接诱因。控制根焊焊缝成形,防止焊瘤产生,并且在中间施焊过程中控制焊接热输入量是防止该裂纹产生和扩展的主要途径。 相似文献
16.
17.
针对镍钼矿中钼酸钙浮选回收率低、丢弃造成资源浪费和环境污染等问题, 在工艺矿物学研究基础上, 对镍钼矿中硫化矿物浮选尾矿进行了开路实验和闭路实验, 设计了氧化钼浮选流程, 并利用分子动力学模拟研究了捕收剂分子在矿物解离面的吸附过程, 结果表明:镍钼矿中硫化矿物浮选尾矿主要含钼矿物为钼酸钙, 脉石矿物主要为氟磷灰石和黄铁矿; 通过闭路浮选试验得到了Mo品位3.24%、Ni品位3.37%、Mo回收率69.15%、Ni回收率62.44%的精矿; 捕收剂油酸分子在钼酸钙(111)面吸附强于氟磷灰石(010)面和黄铁矿(110)面, 从而实现了浮选过程中钼酸钙和脉石矿物的分离, 说明捕收剂CSU-Y可浮选分离钼酸钙和脉石矿物。 相似文献
18.
19.
20.