Free vibrations of laminated composite plates using second-order shear deformation theory

A complete set of linear equations of the second-order theory of laminated composite plates are obtained. A generalized Levy type solution in conjunction with the state space concept is used to analyze the free vibration behavior of cross-ply and antisymmetric angle-ply laminated plates. Exact fundamental frequencies of cross-ply plate strips are obtained for arbitrary boundary conditions. The exact analytical solutions are obtained for thick and moderately thick plates as well as for thin plates and plate strips. It is shown that the results of the second-order theory are very close to the results of the first-order and third-order theories reported in the literature, and different from those of the classical Kirchhoff’s theory for thick laminates.     

Boundary characteristics in Heavily Deformed Metals

The potential of creating nanostructured metals by plastic deformation to very high strains is currently the subject of intensive research. An important part of this research concerns evolution of the characteristics of deformation induced boundaries, in particular boundary spacing and boundary misorientation. The aim of this paper is to give an overview of the present understanding of the relations between these characteristics, the microscopic deformation mechanisms and the macroscopic deformation mode.     

Measurement optimum condition of speckle interferometry based on dual-camera technique

The speckle interferometer based on multi-camera technology using two cameras is applied to a dynamic deformation measurement of the package of an electronic device. To perform high precise measurement by this method, the optimum conditions for measurements are discussed concerning the size of speckle and the frequency of carrier signals. Under the optimum conditions, the deformation process of the package during the operation of an operational amplifier is measured. Then, the local maximum deformation can be estimated as 150 nm from experimental results. From the results, it can be also confirmed that electronic devices are deformed by the stress of a heat by an operation every second during the operating time.     

DMA thermal analysis of different parts of potato tuber

Dynamic mechanical analysis (DMA) was applied to three potato tissues (‘cortex’, ‘pith’, and ‘side’ surface) of two cultivars (more waxy ‘Nicola’ and more mealy ‘Saturna’) in temperature scans in the range 30–90 °C and constant air humidity of 90%. The obtained scans indicate peaks in both storage and loss module of elasticity (SM and LM, respectively) at temperatures higher than 70 °C – so called ‘starch’ peak (SP) – as was observed previously. The peak value increase with increasing potato dry matter (DM) content, below DM content approximately 14% no SP is observed (‘Nicola pith’). Slope analysis of the basic parameters: SM, LM, and loss tangent (LT) was performed and further characteristic points on the temperature plots were found: (i) in temperature range A (30–40 °C) maximum of SM and LM and minimum of LT, (ii) in temperature range B (40–50 °C) minimum of SM and LM slopes corresponding to point of inflection on SM-T and LM-T plots, (iii) at about 50 °C, big peak in LT in side tissue only, (iv) at about 70 °C just prior the ‘starch’ peak, big peak in LT that is more marked in ‘pith’; this peak denoted as ‘I’ influenced the ‘starch’ peak ‘II’. It was found that both cultivar and part of the tuber influences the DMA temperature plots.     

On deformation twinning in a 17.5% Mn-TWIP steel: A physically based phenomenological model

TWinning Induced Plasticity (TWIP) steel is a typical representative of the 2nd generation advanced high strength steels (AHSS) which exhibits a combination of high strength and excellent ductility due to the deformation twinning mechanisms. This paper discusses the principal features of deformation twinning in faced-centered cubic austenitic steels and shows how a physically based macroscopic model can be derived from microscopic-level considerations. In fact, a dislocation-based phenomenological model, with internal state variables including dislocation density and micro-twins volume fraction describing the microstructure evolution during deformation process, is proposed to model the deformation behavior of TWIP steels. The originality of this work lies in the incorporation of a physically based model on twin nucleation and volume fraction evolution in a conventional dislocation-based approach. Microstructural level experimental observations with scanning electron microscope (SEM) and transmission electron microscope (TEM) techniques together with the macroscopic quasi-static tensile test, for the TWIP steel Fe-17.5 wt.% Mn-1.4 wt.% Al-0.56 wt.% C, are used to validate and verify the modeling assumptions. The model could be regarded as a semi-phenomenological approach with sufficient links between microstructure and the overall mechanical properties, and therefore offers good predictive capabilities. Its simplicity also allows a modular implementation in finite element-based metal forming simulations.     

Split Hopkinson pressure bar testing of 3D woven composites

Results from a series of split Hopkinson pressure bar (SHPB) tests on 3D woven tetxile composites (3DWC) are presented. These tests were done to determine the rate dependent compression response of 3DWC. Three different configurations of the 3DWC, corresponding to compression response in the plane of the material and through-the-thickness direction (out-of-plane) were studied. The rate dependent responses were compared against quasi-static test results and it was found that 3DWC showed an increase in strength in all three directions studied, however, accompanied by a transition in the failure mechanism. The in-plane orientations showed the largest increase in (about 100%) strength at the elevated rates of loading. A follow-on paper provides finite element based results that correspond to the experimental results presented here.     

Deformation-induced austenite grain rotation and transformation in TRIP-assisted steel

Uniaxial straining experiments were performed on a rolled and annealed Si-alloyed TRIP (transformation-induced plasticity) steel sheet in order to assess the role of its microstructure on the mechanical stability of austenite grains with respect to martensitic transformation. The transformation behavior of individual metastable austenite grains was studied both at the surface and inside the bulk of the material using electron back-scattered diffraction (EBSD) and X-ray diffraction (XRD) by deforming the samples to different strain levels up to about 20%. A comparison of the XRD and EBSD results revealed that the retained austenite grains at the surface have a stronger tendency to transform than the austenite grains in the bulk of the material. The deformation-induced changes of individual austenite grains before and after straining were monitored with EBSD. Three different types of austenite grains can be distinguished that have different transformation behaviors: austenite grains at the grain boundaries between ferrite grains, twinned austenite grains, and embedded austenite grains that are completely surrounded by a single ferrite grain. It was found that twinned austenite grains and the austenite grains present at the grain boundaries between larger ferrite grains typically transform first, i.e. are less stable, in contrast to austenite grains that are completely embedded in a larger ferrite grain. In the latter case, straining leads to rotations of the harder austenite grain within the softer ferrite matrix before the austenite transforms into martensite. The analysis suggests that austenite grain rotation behavior is also a significant factor contributing to enhancement of the ductility.     

900 MW PWR containment mechanical behavior characteristics during containment test

Containment mechanical behavior characteristics are one of the important checking items during 900 MW PWR containment test. This article describes these characteristics (including strain, displacement and temperature influence) systematically. Especially some intrinsic characteristics are discussed and some new viewpoints are provided. We believe that it has some reference value to other containment test.     

Development of numerical scheme for phase field crystal deformation simulation

The phase field crystal (PFC) method is anticipated as a new multiscale method, because this method can reproduce physical phenomena depending on atomic structures in metallic materials on the diffusion time scale. Although the PFC method has been applied to some phenomena, there are few studies related to evaluations of mechanical behaviors of materials by appropriate PFC simulation. In a previous work using the PFC method, tensile deformation simulations have been performed under conditions where the volume increases during plastic deformation. In this study, we developed a new numerical technique for PFC deformation simulation that can maintain a constant volume during plastic deformation. To confirm that the PFC model with the proposed technique can reproduce appropriate elastic and plastic deformations, we performed a series of deformation simulations in one and two-dimensions. In one- and two-dimensional single-crystal simulations, linear elastic responses were confirmed in a wide strain rate range. In bicrystal simulations, we could observe typical plastic deformations due to the generation, annihilation and movement of dislocations, and the interaction between the grain boundary and dislocations. Moreover, the deformation behaviors of a nanopolycrystalline structure at high temperature were simulated and the intergranular deformations caused by grain rotation and grain boundary migration were reproduced.