Radiometric Calibration and Validationof TG-1 Hyper-spectral Imager

TG-1,the first Chinese space laboratory module launched on 29 September 2011,has accumulated large numbers of high-resolution image data by the hyper-spectral imager.However,these images still can’t be applied to quantitative analysis because of the huge spectral and radiance difference between ground and onboard conditions.So a radiometric calibration is very necessary to correct these laboratory and on-board radiance calibration parameters for better quantitative application.This paper aims to calibrate TG-1 hyper-spectral imager using reflectance-based calibration method through performing ground calibration experiments on 3 February and 6 March 2011.Firstly,this study used the ground experiment data on 6 March to obtain each channel’s calibration correction coefficients,which were different a lot from laboratory and on-board ones,relative error in all channels are bigger than 10 percent.Then,the calibration experiment data on 3 February 2011 were used to validate the result.Results show that calibration correction coefficients improved the image accuracy,the calibration and validation experiments’ results are in good agreement.In most channels,the relative errors are less than 10 percent,except that bigger error appears in absorption channels.Therefore,this calibration experiment renewed the calibration coefficients,and improved the quantitative level of the TG radiance products.     

复杂地形影响下雷达探测范围表现算法研究

通过分析雷达探测范围边界与数字地形高程的相对位置关系,提出一种基于几何光学原理的雷达探测范围受复杂地形影响的修正算法。采用雷达传播衰减模型和混合采样方法,应用该修正算法,实现了对复杂地形影响下雷达探测范围的修正。实验结果表明,该算法不仅对复杂地形适应性强,而且表现效果真实直观。     

电子称重仪的精度分析

分析了ＯＣＳ－ＸＹ型称重仪的误差产生原因,在原称重仪的基础上,利用微处理器的软硬件技术对系统误差、随机误差和疏失误差进行了一系列的校正,提高了测量精度及可靠性。     

柴窝堡二维地震资料目标处理方法研究应用

柴窝堡地区地震资料采集于上世纪八十年代,受当时技术条件限制,老资料能量弱,覆盖次数低,导致处理成果信噪比低,难以满足解释要求。在重新处理过程中,通过对地震地质资料特点的全面分析,针对处理目标从静校正、噪音衰减、精细速度分析到偏移制定了一系列有针对性的处理方法,通过应用实施取得了很好的效果。     

500kV电容式电压互感器顶端接地对分压电容C_2的影响

在新建变电站的验收中,发现电容式电压互感器(CVT)顶端接地对分压电容C2的测量值产生了影响。通过对测量C2时原理接线图的分析,知道由于顶端接地,每次测得的电容值C2均需要除以校正系数K值后,方能够得到准确的实际值,再进行前、后数据比较,可以保证每次所测得的电容值前、后具有可比性,并能够准确地判断CVT的绝缘状况是否良好。     

Knowledge-directed Adaptation in Multi-level Agents

Most work on adaptive agents have a simple, single layerarchitecture. However, most agent architectures support three levels ofknowledge and control: a reflex level for reactive responses, a deliberatelevel for goal-driven behavior, and a reflective layer for deliberateplanning and problem decomposition. In this paper we explore agentsimplemented in Soar that behave and learn at the deliberate and reflectivelevels. These levels enhance not only behavior, but also adaptation. Theagents use a combination of analytic and empirical learning, drawing from avariety of sources of knowledge to adapt to their environment. We hypothesize that complete, adaptive agents must be able to learn across all three levels.     

控制系统校正环节优化设计的计算机辅助分析

结合共轭梯度法,借助于MATLAB软件,提出一种控制系统校正环节优化设计的新方法.该方法利用了MAT-LAB软件中的符号数学工具箱、控制系统工具箱和优化设计工具箱,使设计简单、快捷,提高了编程效率.     

前向误码纠错技术在特高压电网通信中的应用

简要介绍了超长距离无中继光纤通信的主要技术,如光纤放大技术、远泵放大技术、喇曼放大技术、色散技术、调制技术等。文章重点说明了前向误码纠错(FEC)技术的工作原理,及其在超长距离无中继光纤传输系统中的应用,为业内人士提供参考与借鉴。     

高效率的BOOST型功率因数校正预调节器

有源功率因数校正(PFC)通常采用Boost变换器，在低压90V输入时，其输出电压调节在380V，此时变换器效率最低。该文提出一种变输出电压的控制方式，其输出电压随着输入电压的变化而变化。这种方法可以缩短开关管的导通时间，减小流经开关管的电流有效值，从而降低其导通损耗，提高变换器的效率。分析了Boost PFC变换器的损耗分布和控制方法。最后在一台1200W的原理样机上进行实验验证，还对比快恢复二极管和SiC二极管的关断特性，给出实验结果。     

维氏硬度曲面修正系数的计算机拟合

根据GB／T 4340．1-1999所附的各类曲面维氏硬度修正系数表，基于多项式拟合技术，给出了曲面维氏硬度修正系数关于压痕对角线长度与曲面直径比值的解析函数表达式，并对维氏硬度值的修约规律进行了总结。