板制多楔皮带轮冲压工艺与模具设计

板制多楔皮带轮形状复杂,需要多道工序方能成形。本文介绍了其成形工艺,重点介绍了模具结构及模具设计中需要注意的一些问题,对设计同类模具具有一定的参考价值。     

Comparative study of Ni-silicide and Co-silicide for sub 0.25-μm technologies

In this work, the phase formation is compared for Ni- and Co-silicidation with and without Ti cap. In addition, the electrical performance of Ni-silicidation with and without Ti-cap is investigated and compared to the performance of a Co-silicidation process with a Ti cap that has the same Si consumption. The lateral confinement of the silicide in the active areas is also studied.     

WireWarping: A fast surface flattening approach with length-preserved feature curves

This paper presents a novel approach — WireWarping for computing a flattened planar piece with length-preserved feature curves from a 3D piecewise linear surface patch. The property of length-preservation on feature curves is very important to industrial applications for controlling the shape and dimension of products fabricated from planar pieces. WireWarping simulates warping a given 3D surface patch onto plane with the feature curves as tendon wires to preserve the length of their edges. During warping, the surface-angle variations between edges on wires are minimized so that the shape of a planar piece is similar to its corresponding 3D patch. Two schemes — the progressive warping and the global warping schemes are developed, where the progressive scheme is flexible for local shape control and the global scheme gives good performance on highly distorted patches. Experimental results show that WireWarping can successfully flatten surface patches into planar pieces while preserving the length of edges on feature curves.     

Testing formability in the hot stamping of HSS

This paper presents an innovative experimental procedure, based on Nakazima test, for evaluating the formability limits in the hot stamping of high strength steel (HSS) which is capable of generating formability data suitable for an FE modelling of the process. The approach is based on two complementary tests which are aimed at evaluating the actual phase transformation kinetics for the material under deformation conditions and the combinations of microstructure, temperature and straining path that lead to localized necking or fracture.     

用离子束混合及快速热处理方法形成钽的硅化物

本文描述用离子束透过钽金属膜进行混合和快速热处理方法来形成钽的硅化物.用溅射方法在P型硅衬底上淀积一层金属钽,然后用砷离子束透过钽金属模进行混合,采用快速热处理后形成了平整的硅化钽薄层.使用厚度为500埃的钽金属膜,得到钽的硅化物薄层电阻为5.5Ω/□.研究了砷离子能量、剂量及钽膜厚度对钽的硅化物薄层电阻的影响.用透射电镜和台阶仪对所形成的硅化钽进行了分析和厚度测量.     

A new extrinsic dc model for high speed lattice matched InAlAs/InGaAs/InP HEMT with a predicted 135 GHz cut-off frequency

Extrinsic lattice matched InAlAs/InGaAs/InP HEMT model, incorporating the parasitic source and drain resistance, for very high frequency application is developed. The current voltage characteristics and the transconductance have been evaluated and the influence of carrier concentration dependent mobility on frequency has also been analyzed. A cut-off frequency of 135 GHz is obtained.     

金属板料成形工艺CAD／CAM智能化集成研究

根据现行发展状况,探讨了金属板料成形CADCAE智能化集成的必要性和可行性,分析了其中要解决的一些关键技术,提出了实现CADCAE智能化集成的方法。     

The application of a ductile fracture criterion to the prediction of the forming limit of sheet metals

To predict accurately the forming limit in sheet metal forming, the combination of FE simulation with tension tests is adopted in this paper to determine the material constants p and C in a ductile fracture criterion (DFC), which is advanced by the author. Forming limits of bore-expanding, hemispherical punch bulging and deep drawing (cylindrical, square-cup parts) are predicted by means of the DFC. Comparison of the results predicted by the DFC with experimental values shows that the precision of forming limit predicted by material constants obtained by the combination method is more accurate than that predicted by material constants obtained by the tension method, and that the critical punch stoke and the fracture initiation position in forming processes above mentioned are predicted accurately by the DFC.     

Sheet metal forming of piezoceramic-metal-laminar structures—Simulation and experimental analysis

Adaptive systems with piezoelectric components offer significant opportunities for the active control of dynamic behaviour. Vibration and acoustics control as well as structural health monitoring are also possible. However ineffective production technologies prevent industrial applications. The authors are therefore proposing the integration of piezo-modules inside a double-layer sheet. The use of semi-cured adhesive avoids shear-forces being transferred to the piezo-modules during forming. After forming the adhesive will cure and the transfer of piezoelectric strain to the sheet is made possible. A detailed finite-element-model incorporating the electro-mechanical characteristics of the piezo-modules has been developed. The simulation results were validated experimentally.