分批加分散剂时苯乙烯悬浮聚合瞬间液滴直径和分布

在苯乙烯悬浮聚合中研究了分批加分散剂体系磷酸三钙(TCP)或 TCP 和聚乙烯醇(PVA)时的加入方式对瞬间液滴大小和分布的影响。考察了体系液滴分散和合一的特点。实验观察到分批加入分散剂体系时液滴大小分布的变化规律,呈由单峰分布过渡到双峰分布,最后又发展为单峰分布。这与分散剂体系一次加入相比,后者仅出现单峰分布逐渐过渡到双峰分布。     

分散聚合及单分散聚合物微球制备技术

分散聚合是一种新的聚合方法 ,反应开始前 ,单体、引发剂和分散剂均溶解在介质中 ,随着反应的进行 ,当聚合物链达到临界值时便会从介质中分离出来 ,并借助于分散剂稳定地悬浮在介质中。分散聚合方法已被应用于许多领域 ,如涂料工业、生物工程、医学、信息产业、化学工业等。介绍了分散聚合及单分散聚合物微球制备技术的进展 ,并对其聚合机理及聚合反应影响因素进行了概述。     

Preparation of micron‐size monodispersed PS/P(St/MAA) microspheres by seeded dispersion polymerization

Uniform polystyrene (PSt) particles with the size of 1.9 μm were first prepared via dispersion polymerization, and then used as the seeds in a second‐stage dispersion copolymerization of styrene (St) and methacrylic acid (MAA) to produce carboxyl‐carrying microspheres. The PSt seed particles were swollen by monomer mixture of St and MAA, including an oil‐soluble initiator 2,2′‐azobisiso‐butyronitrile (AIBN), before polymerization. Finally, uniform PS/P(St/MAA) (polydispersity index, PDI = 1.02) microspheres with the size of 2.2 μm were obtained. The average particle size and size distribution of the final microspheres were investigated. MAA contents between 54 and 97 mg/g were detected from the PS/P(St/MAA) particles produced under different conditions. Dispersion medium has great influence on the kinetics of polymerization, due to its effect on the partitioning of monomers, solvents, and initiator in the particle phase, probably as well as on the conformation of the dispersion agent on the surface of the particles. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3586–3591, 2006     

基于TEM图像的CNT溶液分散均匀性分形方法

针对传统评价方法的不足,提出了一种以分形理论为数学模型基础的碳纳米管长度分布及分布均匀性的定量评价方法.将碳纳米管溶液TEM图像进行处理,得到简化矩阵,以简化矩阵的第1个元素为原点,提取不同步长及该步长内所有元素的和,在双对数坐标中以拟合直线的斜率作为碳纳米管长度分布参数p1.以TEM图像的中心为圆心做圆,提取不同半径圆内的碳纳米管数量,在双对数坐标中以拟合直线斜率的倒数作为分散均匀性参数p2.将该方法应用于不同方法分散的碳纳米管分散均匀性的描述,结果验证了该方法能正确地评价碳纳米管的长度分布及其分布均匀性.     

云重心方法在舰炮维修性评价中的应用

针对已有的云重心评价方法中评价云发生器的参数设置不合理问题,提出了2倍熵规则,并以此为基础建立了熵参数确定模型;给出了专家个体区间数与平均区间数之间的差异度计算方法,从而建立了超熵参数确定模型。针对云重心偏离度的求解模型繁琐且有偏差的问题,建立起定量评价等级界定的区间数与定性评语对应的区间数之间的等比转换关系,将定量指标的集结值映射到定性评语对应的区间数中,并简化了求解模型。最后通过某舰炮维修性评价实例,验证了改进模型的科学性和合理性。     

半芳香族耐高温尼龙PA6T/6I基LDS功能材料制备及性能

采用半芳香族耐高温尼龙聚对苯二甲酸/间苯二甲酸己二胺(PA6T/6I)为树脂基体,铜铬氧化物为激光镭射助剂,制备了PA6T/6I基的激光直接成型(LDS)功能材料。采用扫描电子显微镜对激光镭射助剂分散状态及LDS功能材料模塑器件的表面形貌能进行了表征,使用热失重分析仪、差示扫描量热仪对LDS功能材料的热失重行为、熔融结晶性能进行了表征,研究了激光镭射助剂添加量对LDS功能材料的力学性能、热稳定性、化学镀性能的影响,同时研究了PA6T/6I熔融结晶性能和注塑模具温度对于模塑器件表面、外观的影响。结果表明,偶联剂的添加有利于改善激光镭射助剂在PA6T/6I树脂基体中的分散,其中环氧类的偶联剂KBM–403处理后的LDS镭射助剂分散效果最佳。激光镭射助剂添加量的增加,会造成LDS功能材料拉伸强度、弯曲强度、冲击强度及初始分解温度降低。激光镭射助剂添加量在8%时,预镀铜上镀时间和镀层覆盖时间最短,化学镀效果最佳。当注塑模具温度为175℃时,玻纤增强PA6T/6I基LDS功能材料模塑器件的外观最佳。     

Fabrication and properties of low oxygen grade Al2O3 dispersion strengthened copper alloy

The low oxygen grade Al2O3 dispersion strengthened copper alloy without hydrogen-fired expansion was fabricated by the technique of vacuum hot press and hot extrusion. The mechanical and electrical properties measurements and microstructures observation on as-hot extruded, as-cold drawn and as-annealed Cu-Al2O3 alloy were conducted. The results show that the addition of a suitable amount of boron in the alloy can lower the residual free oxygen content and then inhibit the hydrogen-fired expansion. The density, σb, σ0.2, hardness, δ and electrical conductivity of the alloy reach 8.86 g/cm^3 (relative density of 99.6%), 340MPa, 250MPa, HB95,24% and 93%(IACS) respectively after hot extruded with the extrusion ratio of 30:1. Its properties have no change after annealed at 900℃ for 1h. Its strength increases after cold drawing, while its ductility and electrical conductivity drop gradually. Various properties of the cold drawn alloy can recover to those of as-extruded after annealed at 900℃ for 1h without the occurrence of recrystallization.     

The high-temperature oxidation of Ni-20%Cr alloys containing various oxide dispersions

The oxidation behavior of Ni-20%Cr alloys containing approximately 3 vol.% Y₂O₃, ThO₂, and A1₂O₃ as dispersed particles has been examined in the temperature range 900 to 1200° C in slowly flowing oxygen at 100 Torr. The results show that the oxidation behavior of the Y₂O₃-, ThO₂-, Al₂O₃-, and Ce0₂-containing alloys is very similar and that some anomalies in the behavior of the ThO₂-containing alloy might be explained by the slower rate of chromium diffusion in this coarse-grained alloy. Two Al₂O₃-containing alloys were studied. One with a relatively coarse dispersoid size behaved in a manner analogous to a dispersion-free Ni-30% Cr alloy at 1100°C. The other alloy contained a dispersion of fine Al₂O₃ particles and behaved exactly like the Y₂O₃-containing alloy at 1000 and 1100°C, but at 1200° C oxidized at a faster rate. It has been shown that the adherent scales on dispersion-containing alloys have a stabilized fine grain size, whereas the nonadherent scales on dispersion-free alloys undergo grain growth.This work has been supported by the Naval Air Systems Command under Contract No. N00019-72-C-0190.     

XD反应合成Al3Ti,α-Al2O3和TiB2/Al复合材料的界面结构

借助于SEM和TEM研究了Al—TiO2-B2O3系热扩散反应法合成铝基复合材料的界面结构。结果表明：在B2O3与TiO2摩尔比小于1时，增强相由棒状的Al3Ti及颗粒状的TiB2和α-Al2O3组成。Al3Ti与基体的界面干净、相容性好，在基体中分布均匀；TiB2与铝基体界面干净，并存在以下位向关系：[231^-]Al∥[0001]TiB2，（204^-）Al∥（2420^--）TiB2，可成为基体结晶时的核心，细化基体晶粒；口一Al2O3与铝基体的润湿性差，被推挤到基体颗粒的界面呈偏聚状态，并存有孪晶现象，其孪晶面为（111），孪生方向为[112^-]。