On the forced vibration of the fiber partially immersed in fluid

In this paper an experimental and theoretical investigation of the forced vibration of a partially immersed fiber has been carried out. An optical method utilizing a forward light scattering pattern has been used to detect a small (<1.0 μm) vibration amplitude of the fiber. The physical and mathematical model of the partially immersed fiber vibration has been put forward. Based on an analytical solution of the model, natural frequencies of the partially immersed fiber vibration have been found; they are consecutive positive roots of the transcendental equation. An “effective” speed of the wave propagation over the fiber has been introduced, which allows one to find the physical meaning of normal modes of the partially immersed fiber vibration. Theoretical predictions agree well with experimental data. The sensor exhibits an excellent sensitivity and could be used for measuring physical properties of fluids and liquid level.     

利用铋酸盐光纤高非线性效应实现40Gb/s全光3R再整形

该文研究的重点是全光3R再生技术中的再整形方法。研究了一个利用光纤的非线性的基于交叉相位调制与自相位调制的40Gb/s归零信号的再整形方法。文中使用软件Optisystem 3.0分别对基于高非线性光纤中的自相位调制和交叉相位调制实现再整形,并进行了仿真实验。该文提出的方案整形后得到的3R再生信号的质量得到了大幅改善。     

用于油库监测的光纤Bragg光栅传感器实验研究

通过对三种光纤Bragg光栅传感器的实验研究,得出实验数据并进行分析,表明光纤光栅传感器用于油库状态参数监测是可行的。该文介绍了分布式监测技术领域的一种新型技术——光纤Bragg光栅监测网络技术,指出了其相对传统技术所具有的独特优越性。最后,提出了一种基于光纤Bragg光栅传感技术的油库监测网络。     

污水处理厂的再生水工艺自控系统

本文以营口污水处理厂再生水自动化控制系统为例,详细介绍了该控制系统的配置和功能。目前,这套系统已经运行了两年多,不仅节省了劳动力、提高了管理水平,而且获得了较高的经济效益。     

基于光纤环网的隧道火灾监控系统研究

文章对基于光纤环网的隧道群火灾报警系统进行研究,分析了其优缺点,提出了解决办法,并完成改造,应用于实际.     

Towards robust grasping: An analysis of in-hand object motion with FBG optical fibers as force sensing technology

To enable or allow for advanced manipulation scenarios in the envisaged future in robotic manipulation, the introduction of tactile or force-sensing technology is essential. This work introduces a study on a novel integration of fiber sensing elements inside the fingers of robotics grippers that allow obtaining accurate interaction forces during object manipulation. The study focuses on in-hand object motion and analyzes the objects’ dynamic behaviors during grasping or contact phases. The proposed approach classifies the behavior of the gripper-object interaction in real-time by looking at the measured forces in the orthogonal direction of the gripper’s fingers after a filtering stage. The methodology is validated theoretically and evaluated with real experiments using objects presenting different shapes, sizes, and surface properties.     

Single-mode fluorotellurite glass fiber

By multi-stage rod-in-tube fiber drawing process, a single-mode fluorotellurite glass fiber was fabricated and reported for the first time. Benefiting from chemical–physical dehydration process to remove water and OH⁻ groups, the propagation loss was decreased to 1.9 dB/m at 1550 nm and the infrared window is extended from 2.8 μm to 4.2 μm, i.e. a new kind of mid-infrared glass fiber. The fiber is with a small core of 3.52 μm in diameter to meet single-mode condition, and the effective nonlinear parameter γ was estimated to be 236.7 W⁻¹ km⁻¹ at 1550 nm by using continuous-wave self-phase modulation method. © 2015 Elsevier B.V. All rights reserved.     

不同拓扑结构FC-AE-1553B网络性能研究

研究点对点、交换式与仲裁环3种不同拓扑结构的网络,建立FC-AE-1553B网络的Markov模型,并分析单点故障对不同拓扑结构总线的影响。仿真结果表明,基于点对点结构的FC-AE-1553B网络在传输NT节点到NC节点的数据流时,具有最小时延,基于交换机实现的FC-AE-1553B网络在传输NT节点到NT节点的数据时,传输性能较优。     

光纤无线电系统中的新型探测法研究

光纤无线电系统利用光载波携带毫米波信号在中心站和基站之间构成上行和下行传输链路,能够满足宽带无线接入系统的需求.利用光外差的方法产生毫米波信号是光载毫米波最简单和直接的方式.分析了在光纤无线电系统中利用光纤布拉格光栅从可调谐激光器中反射出两束相位近似相等的相干光,采用平衡探测产生了毫米波信号,降低了相位噪声和强度噪声对产生的毫米波信号的影响.     

Tool path smoothing of a redundant machine: Application to Automated Fiber Placement

Automated Tape Laying and Fiber Placement of composite materials are the two principal automated processes used for fabrication of large composite structures in aeronautical industry. The aluminum parts produced by High Speed Machining tend to be replaced by carbon fiber composite parts realized with these processes. However, structural parts present reinforcement zones which disturb the tool path follow-up and generate an increase of the manufacturing time. Thus, this paper deals with the optimization of tool paths of a 7-axis machine tool of Fiber Placement with the objective of reducing the manufacturing time while ensuring the requested quality of the final part. In this paper, two complementary methods are detailed. The first method takes advantage of the degree of redundancy of the machine tool to decrease the kinematic loads of the control joints. The second method aims to smooth the orientation of the machine head along the tool path while ensuring quality constraints. These two methods are then applied on a test tool path and bring to a significant decrease of the manufacturing time (32.9%).