3D Modeling of the preparation process of metal rubber material

Based on the analysis of the preparation of metal rubber (MR) and two pivotal hypotheses,the uniform distribution and the unaltered topological structure of wires in the radial direction of columns in the punch process,a 3D parametrical model was established based on four approaches:helix-making,planar roughcast-weaving,planar roughcast-rolling,and 3D roughcast punching.In the modeling process,5 lattice types of weave patterns in planar roughcast were put forward,and 10 quantificational modeling parameters ...     

Relationship between the microstructure and reaction performance of aluminosilicate

A systematic study was conducted to comprehend the mechanism of thermal activation of silica-alumina materials by using 29 Si and 27 Al magnetic angle spinning nuclear magnetic resonance (MAS NMR) spectroscopy.The reaction performance of silica-alumina-based materials with different molar ratios of Si/Al,which were thermally activated,was also investigated.With the increase in calcining temperature,the coordination of Al in metakaolin becomes four,five,and six firstly,and then transforms completely to four ...     

Decarburization rate of RH refining for ultra low carbon steel

The decarburization behaviors of ultra low carbon steel in a 210-t RH vacuum degasser were investigated under practical operating conditions.According to the apparent decarburization rate constant (KC) calculated by the carbon content in the samples taken from the hot melt in a ladle at an interval of 1-2 min,it is observed that the total decarburization reaction period in RH can be divided into the quick decarburization period and the stagnant decarburization period,which is quite different from the tradit...     

曲轴偏置机构原理在钢板滚切剪机设计中的应用

以空间七连杆滚切剪机运动轨迹方程为基础,采用某公司2800mm的曲轴偏置新型结构的单轴双偏心定尺滚切剪为研究对象。对曲轴偏置前后及不同偏置量的钢板剪切力、连杆力、保持剪刃间隙恒定的后滑道推力进行了分析对比。发现采用曲轴偏置后,在前曲柄提刀时刻机构仍然能够保持足够大的后滑道推力,机构在采用60mm-100mm的偏移量时后滑道压力同侧向力最接近平衡。理论分析结果及现场钢板剪切质量表明曲轴偏置机构在保持剪架在剪切过程中平稳,保证剪刃间隙恒定发挥了重要作用。     

Similarity identification method on formational interfaces and application in general granite

An instrumented drilling system can be applied for the acquisition of drilling process parameters.The system can provide continuous and huge data for geotechnical engineering.However, due to the complexity of ground strata, the variation in the drilling parameters with stratigraphical characteristics is great and the correlation between likely comparable parameters is not high, which limits the use of conventional correlation approaches in this field.How to use the data for engineering and how to get a reasonable interpretation for the relationships among the drilling parameters, as well as between a drilling parameter and formational character-istics, become a technical choke point for the development and application of the instrumented drilling system.Based on similarity criteria, the extraction of sample data and characteristics, the pretreatment of data and feature matching algorithms have been ana-lyzed and an approach of slope coefficient searching identification has been established.A case study was carried out for the similar-ity between the rotational speed of the drill bit, flushing pressure, and effective thrust force graphics in general weathered granite.The result shows that the similarity coefficients between the rotational speed of the drill bit, flushing pressure, and effective thrust force are 0.72 and 0.83, respectively.Although there are differences between the distances of the graphics, the curves of both rota- tional speed and flushing pressure agree with the effective thrust curve in shape, which provides a possible method for the identifica- tion of various formations by use of the similarity between feature drilling parameters.     

Effects of welding wire composition and welding process on the weld metal toughness of submerged arc welded pipeline steel

The effects of alloying elements in welding wires and submerged arc welding process on the microstructures and low-temperature impact toughness of weld metals have been investigated.The results indicate that the optimal contents of alloying elements in welding wires can improve the low-temperature impact toughness of weld metals because the proentectoid ferrite and bainite formations can be suppressed,and the fraction of acicular ferrite increases.However,the contents of alloying elements need to vary along with the welding heat input.With the increase in welding heat input,the contents of alloying elements in welding wires need to be increased accordingly.The microstructures mainly consisting of acicular ferrite can be obtained in weld metals after four-wire submerged arc welding using the wires with a low carbon content and appropriate contents of Mn,Mo,Ti-B,Cu,Ni,and RE,resulting in the high low-temperature impact toughness of weld metals.     

Evolution of carbides and carbon content in matrix of an ultra-high carbon sintered steel during heat treatment process

DTA, thermal expansion, XRD, and SEM were used to evaluate the effect of quenching temperature on the mechanical properties and microstructure of a novel sintered steel Fe-6Co-1Ni-5Cr-5Mo-1C. Lattice parameters and the mass fraction of carbon dissolved in the matrix of the steel quenched were investigated. It is discovered that the hardness of the steel increases with quench-ing temperature in the range of 840-900℃ and remains constant in the range of 900 to 1100℃. It decreases rapidly when the tem-perature is higher than 1100℃. The mass fraction of carbon dissolved in the matrix of the steel quenched at 840℃ is 0.38, but when the quenching temperature is increased to 1150℃, it increases to 0.98. The carbides formed during sintering are still present at grain boundaries and in the matrix of the steel quenched at low quenching temperatures, such as 840℃. When the quenching temperature is increased to 1150℃, most of the carbides at grain boundaries are dissolved with just a small amount of spherical M23C6 existing in the matrix of the quenched steel.     

Numerical simulation on the rheo-diecasting of the semi-solid A356 aluminum alloy

The effect of injection pressure, piston velocity, and the forming temperature of semisolid slurry on the filling behavior of the semi-solid A356 aluminum alloy was investigated by simulation methods. The simulation results show that these processing parameters have an important effect on the filling behavior of the semi-solid A356 aluminum alloy. The slurry flows steadily in the cavity when the injection pressure, the piston velocity, and the forming temperature are low, but it is prone to turbulent flow w...     

Comprehensive assessment on dynamic roof instability under fractured rock mass conditions in the excavation disturbed zone

The damage process of fractured rock mass showed that the fracture in rocks induced roof collapse in Yangchangwan Coal Mine,China.The rock mass was particularly weak and fractured.There occurred 6 large-scale dynamical roof falls in the excavation disturbed zone (EDZ) with the collapsing volume of 216 m3.First,the field detailed geological environment,regional seismic dy-namics,and dynamic instability of roadways were generally investigated.Second,the field multiple-index monitoring measurements for detecting the deep delamination of the roof,convergence deformation,bolt-cable load,acoustic emission (AE) characteristic pa-rameters,total AE events,AE energy-releasing rate,rock mass fracture,and damage were arranged.Finally,according to the time-space-strength relations,a quantitative assessment of the influence of rock-mass damage on the dynamic roof instability was accomplished.     

Experimental study on Ti+Nb bearing ultra-low carbon bake hardening sheet steel hot-rolled in the ferrite region

A Ti+Nb bearing ultra-low carbon bake hardening sheet steel hot-rolled in the conventional austenite region and in the ferrite region with lubrication was experimentally studied.Subsequent cold rolling and continuous annealing processes were also conducted.The results show that microstructures of ultra-low carbon bake hardening hot strips at room temperature are basically irregular polygonal ferrites.The yield strength,ultimate tensile strength,n value,and r value of the No.2 specimen hot-rolled in the ferr...