铁尾矿沥青混合料基本性能及老化耐久性研究

为了避免过度使用天然砂石材料做为沥青混合料的骨料以及符合绿色发展的战略方针，采用固体废弃物铁尾矿来代替砂石材料来制备一种新型的铁尾矿沥青混合料。采用质谱仪对所选用铁尾矿进行化学成分分析，并对不同铁尾矿掺量作用下沥青混合料的针入度、锥入度、软化点、延度、粘度以及老化耐久性等方面进行了研究。研究结果表明:铁尾矿沥青混合料的较佳制备温度选定为180℃；综合经济效益和有效性确定铁尾矿的较佳掺量为30%；相对老化后的铁尾矿沥青材料而言，在同一铁尾矿掺量作用下两种不同沥青混合料老化前的针入度和延度均出现了降低的趋势，但是在同一铁尾矿掺量作用下两种不同沥青混合料老化前的软化点却出现了增大的趋势。综合分析得到:温度为180℃以及铁尾矿掺量为30%制备的沥青混合料可以满足公路的路用要求。所有沥青试样的光谱变化规律基本一致，说明了掺入铁尾矿改性沥青的结构与未掺入铁尾矿沥青的结构基本一致；但是随着铁尾矿掺量的增大，沥青的FT-IR光谱在同一波数作用下却呈现出不断减小的变化趋势，说明了铁尾矿可以有效改善沥青的物理性能。      

Swapping catalytic active sites from cationic Ni to anionic F in Fe–F–Ni3S2 enables more efficient alkaline oxygen evolution reaction and urea oxidation reaction

Electrolysis of water for producing hydrogen instead of traditional fossil fuels is one of the most promising methods to alleviate environmental pollution and energy crisis. In this work, Fe and F ion co-doped Ni₃S₂ nanoarrays grown on Ni foam substrate were prepared by typical hydrothermal and sulfuration processes for the first time. Density functional theory (DFT) calculation demonstrate that the adsorption energy of the material to water is greatly enhanced due to the doping of F and Fe, which is conducive to the formation of intermediate species and the improvement of electrochemical performance of the electrode. The adsorption energy of anions (F and S) and cations (Fe and Ni) to water in each material was also calculated, and the results showed that F ion showed the most optimal adsorption energy of water, which proved that the doping of F and Fe was beneficial to improve the electrochemical performance of the electrode. It is worth noting that the surface of Fe–F–Ni₃S₂ material will undergo reconstruction during the process of water oxidation reaction and urea oxidation reaction, and amorphous oxides or hydroxides in situ would be formed on the surface of electrode, which are the real active species.     

Facile preparation of SnS2 nanoflowers and nanoplates for the application of high-performance hybrid supercapacitors

In this work, the SnS₂ nanoflowers (SnS₂ NFs) were solvothermally prepared in the solvent of ethanol, while SnS₂ nanoplates (SnS₂ NPs) were obtained through the identical conditions except for the solvent of water. The flowers were assembled with numerous nanosheets with very thin thickness, and the NPs exhibited hexagonal shape. When used as the battery-type electrode material for supercapacitors, the SnS₂ NFs delivered a specific capacity of as high as 264.4 C g^?1 at 1 A g^?1, which was higher than the 201.6 C g^?1 of SnS₂ NPs. Furthermore, a hybrid supercapacitor (HSC) was assembled with the SnS₂ as positive electrode and activated carbon (AC) as negative electrode, respectively. The SnS₂ NFs//AC HSC exhibited a high energy density of 28.1 Wh kg^?1 at 904.3 W kg^?1, which was higher than the 24.2 Wh kg^?1 at 844.3 W kg^?1 of SnS₂ NPs//AC HSC. Especially, when the power density was enhanced to the highest value of 8666.8 W kg^?1, the NFs-based device could still hold 20.4 Wh kg^?1. In addition, both HSC devices showed an excellent cycling stability after 5000 cycles at 5 A g^?1. The present method is simple and can be extended to the preparation of other transition metal sulfides (TMSs)-based electrode materials with brilliant electrochemical performance for supercapacitors.     

Cyclic thermal shock resistance for MgAlON–MgO composites obtained with additions of spent MgO–C brick: Microstructure characteristics,thermal shock parameter and thermal shock mechanism

Thermal shock parameters (R, R''', R'''' and R_st) of MgAlON–MgO composites obtained with additions of spent MgO–C brick were calculated using measured mechanical properties and thermal expansion coefficient, determining their resistance to fracture initiation and crack propagation. The cyclic thermal shock experiments of MgAlON–MgO composites performed from 1398 K to ambient temperature indicate that as number of thermal shock cycle increases, retained strength ratio of MgAlON and MgAlON–4.2 wt%MgO sharply decrease and then keep constant, while that of MgAlON–10.5 wt%MgO and MgAlON–15.7 wt%MgO slowly decrease. The reason for the difference is that MgAlON and MgAlON–4.2 wt%MgO show low value of R''' and R'''', and high value of R and R_st. Moreover, precipitation of impurity containing Fe may play a positive role in improvement of thermal shock resistance of MgAlON–MgO composites. MgAlON?4.2 wt%MgO has the maximum retained strength (55 MPa) even after 5 thermal shock cycles, which is expected to be used in the metallurgical industry.     

High-entropy titanate pyrochlore as newly low-thermal conductivity ceramics

Low-thermal conductivity ceramics play an indispensable role in maximizing the efficiency and durability of hot end components. Pyrochlore, particularly zirconate pyrochlore, is currently a highly promising and widely studied candidate for its extremely low thermal conductivity. However, there are still few pyrochlores that offer both stiffness, insulation, and good thermal expansion properties. In this work, the solidification method was innovatively introduced into the preparation of titanate pyrochlore, and combined it with the compositional design of high-entropy. Through careful composition design and solidification control, the high-density and uniform elements distributed high-entropy titanate pyrochlore ceramics were successfully prepared. These samples possess high hardness (15.88 GPa) and Young’s modulus (295.5 GPa), low thermal conductivity (0.947 W·m^?1·K^?1), excellent thermal expansion coefficient (11.6 ×10^?6/K) and an exquisite balance between stiffness and insulation (E/κ, 312.1 GPa·W^?1·m·K), in which the E/κ exhibits the highest value among the current reported works.     

Surface Modification of Co3O4 Nanosheets to Promote Peroxymonosulfate Activation for Degradation of Atrazine

Catalysis Letters - This study proposed a new facile route to rational creating oxygen-vacancy (Vo)-rich surface of Co3O4 nanosheets by acetic acid leaching. The acid leached Co3O4 nanosheets was...     

Experimental study on the load bearing behavior of geosynthetic reinforced soil bridge abutments with different facing conditions

This paper presents an experimental study on reduced-scale model tests of geosynthetic reinforced soil (GRS) bridge abutments with modular block facing, full-height panel facing, and geosynthetic wrapped facing to investigate the influence of facing conditions on the load bearing behavior. The GRS abutment models were constructed using sand backfill and geogrid reinforcement. Test results indicate that footing settlements and facing displacements under the same applied vertical stress generally increase from full-height panel facing abutment, to modular block facing abutment, to geosynthetic wrapped facing abutment. Measured incremental vertical and lateral soil stresses for the two GRS abutments with flexible facing are generally similar, while the GRS abutment with rigid facing has larger stresses. For the GRS abutments with flexible facing, maximum reinforcement tensile strain in each layer typically occurs under the footing for the upper reinforcement layers and near the facing connections for the lower layers. For the full-height panel facing abutment, maximum reinforcement tensile strains generally occur near the facing connections.     

Fabrication and comprehensive structural and spectroscopic properties of Er:Y2O3 transparent ceramics

Transparent Er:Y₂O₃ ceramics with sub-micron grain size (<1 μm) were fabricated by using one-step vacuum sintering followed by hot isostatic pressing (HIPing) technique. The transmission of the undoped Y₂O₃ reaches 83%. The structural characteristics including the phonon energy were investigated through X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) analysis and scanning electron microscopy (SEM) measurement. The overall spectroscopic properties of transmission, fluorescence emission up to 3000 nm, lifetime, up-conversion luminescence, and refractive index were systematically studied for both 0.25 at% and 7.0 at% Er:Y₂O₃ ceramics with different thicknesses. The comparison of the spectra of the fluorescence emission and up-conversion luminescence under both 976 and 808 nm laser excitation was performed. The multiple high-energy-state transitional processes after the excited state absorption (ESA) processes involved in the up-conversion are discriminated between the multi-phonon non-radiative transitions and the radiative transitions according to the measured maximum phonon vibrational energy. The calculation was performed based on the Judd–Ofelt theory.     

异种铁素体耐热钢接头界面组织及其影响

综述了铁素体与铁素体异种金属焊缝（dissimilar metal welds，DMWs）接头界面组织及其影响。结果表明，在焊后热处理或运行温度下的铁素体钢DMWs接头的不均匀界面组织中，通常会形成脱碳层和增碳层。在铁素体钢DMWs焊接接头界面组织影响因素中，焊缝金属的化学成分有重要影响；焊后热处理规范（温度和时间）、工作温度下运行时间的影响较为突出；焊接工艺参数的影响亦不可忽略。异种钢接头界面处近缝区裂纹的产生，以及接头的蠕变强度随Larson Miller 参数增大而下降等不利影响，均为异种钢界面碳迁移行为所导致。焊缝成分控制法是接头界面组织控制或改善的必要条件，而脱碳层部位转移法能有效防止裂纹发生，亦是接头安全运行的重要工艺措施之一。     

天然油脂乙氧基化物稳定高内相乳液影响因素的研究

以棕榈仁油乙氧基化物(SOE-N-60)为表面活性剂稳定高内相乳液(HIPEs)。通过对乳液外观、微观结构、粒径分布、黏度和流变学测试，研究了油相体积分数、SOE-N-60添加量对HIPEs性能的影响，同时对其稳定性进行考察。结果表明：SOE-N-60添加量为0.6%~1.5%（油相体积分数为83%）、油相体积分数为74%~86%（SOE-N-60添加量为1.0%）时可形成稳定的HIPEs，此时乳液液滴内部形成紧密堆积的网络结构，乳液粒径变小，具有弹性凝胶性质，并展现出很好的黏弹性和触变性，且随着油相体积分数和SOE-N-60添加量的增大，乳液黏弹性逐渐增强，同时HIPEs在(-5±1) ℃、(25±1) ℃、(40±1) ℃下贮存24 h时均具有良好的稳定性。