电容式力感知牙周探针设计建模与实验研究

针对当前牙周探针在探诊力控制方面的不足,提出一种基于悬臂梁挠曲效应的差动电容式力感知牙周探针解决方案,设计了探针验证结构,建立了探诊力作用下具有不规则形状的探针工作尖的挠曲模型,导出了探诊力和差动电容之间的求解方程,并通过仿真和实验对模型与方程进行了验证。结果表明,所建立的探针工作尖挠曲模型与静应力仿真结果的最大相对误差不超过±4.5%,所设计的力感知牙周探针多次重复探诊力检测实验的标准差小于均值的0.1%,所导出的求解方程的计算值与实验数据之间趋向一致,以探诊力为拟合权重进行修正后全量程的平均偏差为2.49%,具备进一步产品开发的可行性。     

A charge sharing–based switching scheme for SAR ADCs

This paper presents an energy-efficient switching scheme for successive approximation register (SAR) analogue-to-digital converter (ADC). The proposed scheme employs charge recycling method to keep the capacitor arrays free of transitional energy between bit generations except reset phase. In comparison with the conventional switching scheme, the proposed one achieves 100% transitional energy saving without considering reset phase. In addition, configuration of a 10-bit SAR ADC shows that the proposed switching scheme reduces the capacitor area by 25% compared with the conventional switching scheme.     

ZIF衍生多孔碳纳米纤维用于高效电容去离子的研究

作为一种环保节能的新兴脱盐技术，电容去离子技术正在成为替代反渗透脱盐和电渗析脱盐的一项重要的脱盐技术。各种碳基材料被广泛地应用于电容去离子电极材料的研究，然而大多数碳基材料为粉末状材料，需要添加黏结剂，这必将导致电极材料电吸附能力的下降。利用静电纺丝技术，将ZIF纳米颗粒和聚丙烯腈混纺，并通过分段高温热处理过程，成功合成了具有柔性结构的整体性多孔碳纳米纤维。由于其具有孔道结构的分级分布和较强的亲水性等优良特性，所制得的多孔碳纳米纤维在1.2 V电压下于500 mg/L NaCl溶液中表现出良好的电吸附性能，脱盐量达到了19.92 mg/g，比普通碳纳米纤维提高了一倍以上。     

Investigations on Selectivity of Gas-Liquid Reactions in Capillaries

Biocatalysis offers a broad spectrum of possible ecological and economic advantages over conventional chemical catalysis processes, e.g., lower energy consumption and high enantio selectivity. The focus of this work is on gas-liquid reactions. These are of great importance in the chemical and biochemical industry and subject of current research since they are often limited by mass transfer or show low selectivity. Different suitable biocatalytically gas-liquid reaction systems were tested in capillary reactor designs in order to obtain information about the interaction between reaction and fluid mechanics. Furthermore, an optical measuring method was established. The experiments were performed in batch mode in a glass beaker with a flow cuvette for UV/Vis measurement of product concentration.     

Iron Loss Calculation of AC Filter Inductor for Three‐Phase PWM Inverters

In recent years, remarkable advancement of new power semiconductor devices, such as SiC and GaN, enables the increase of switching frequency of power converters, and hence the volume of passive components, such as ac filters and transformers, can be reduced. However, temperature rise caused by the inductor loss is increasing, and hence iron loss evaluation of the inductor is one of the most important issues to realize high power density converters. Conventionally, an improved generalized Steinmetz equation (iGSE) has proposed in order to calculate the iron loss under a pulse voltage magnetizing condition. However, accurate iron loss calculation of the ac filter inductor used in a PWM inverter cannot be realized. The authors have proposed two methods of iron loss evaluation of ac filter inductors. The first one is a loss map method which can calculate the iron loss without using a real PWM inverter. Another one is an ILA (Inductor Loss Analyzer) which can measure the iron loss in every switching period in a real PWM inverter. In this paper, comparisons of the iron loss between the ILA and the loss map method on both the single‐phase and three‐phase inverters are studied. It is found that iron loss of the ac filter inductor in the three‐phase PWM inverter which is calculated by the loss map method cause a large error on a specific condition. In order to prevent the calculation error, the authors proposed a revised loss map method and proved the effectiveness of the method.     

Application of differential evolution for cascaded multilevel VSI with harmonics elimination PWM switching

Harmonic elimination pulse width modulation (HEPWM) method has been widely applied to multilevel voltage source inverter (MVSI) to remove low frequency harmonics from its output voltage. However, the computation of the HEPWM switching angles for MVSI is very challenging due to several constraints, namely angle sequencing, very tight angular spacing and the numerous possibilities of angles distribution ratio. Realizing the potential of Differential Evolution (DE) to handle complex problems, this work proposes its application to solve the HEPWM problem for cascaded MVSI. Its emphasis is on improving the availability of HEPWM for higher output voltage by extending the maximum range of modulation index (M). It also removes the discontinuities in the switching angles and reduces the number of distribution ratio required to obtain the required solution. Compared to the most advanced (similar) work, i.e., 7-level MVSI with seventeen switching angles, DE covers a wider range of M; the maximum achievable M is 2.80. Furthermore, it exhibits very low second order distortion factor (DF₂): for the worst case, the value of DF₂ is 0.0014%. To verify the viability of the proposed algorithm, simulation is carried out and hardware prototype is constructed. Both results show very good agreement with the theoretical prediction.     

Restraint Method for Overcoming Heating Irregularity and Improving Heating Equipment Efficiency for Beverage Cans Using High‐Frequency Induction Heating

We were able to reduce heating irregularities in equipment for heating beverage cans by using the high‐frequency induction heating method and determining the resulting improvement in the heating efficiency. The heating irregularity between the top and bottom of the can was reduced to less than 3°C by improving the arrangement of the heating coils for the beverage can by thinning the winding and changing the circuit configuration. The efficiency of power conversion was improved from 93.0% to 97.4%. In this paper, the configuration of the equipment and the experimental results are reported.     

Integrated circuit and system design for renewable energy inverters

This study proposes that a novel integrated circuit (IC) and system design for renewable energy inverters can harvest renewable energy to power direct current (DC) and alternating current (AC) loads. In addition, an intelligent synthesis and management tool is developed to design the proposed system and to judge the system’s operational maintenance decisions. Finally, a renewable energy inverter’s information is posted to an online system. Users can obtain the proposed system’s information at any time and place. The accurate and superior performance of the proposed IC and system is confirmed by computer simulations and experimental results.     

Verification of Iron Loss Calculation Method Using a High‐Precision Iron Loss Analyzer

Because of the improved performance of power devices, the volume of the ac filter inductors used in high‐frequency PWM inverters has been reduced. However, the temperature rise in the filter inductor due to this miniaturization has become more pronounced. Therefore, we have proposed an iron loss calculation method for the ac filter inductor. However, the accuracy of the value calculated via the loss map method cannot be verified, because the iron loss arising during each switching period cannot be measured with conventional power measuring instruments. In order to resolve this problem, we developed an inductor loss analyzer (ILA), which allows precise measurement of the iron loss in the inductor during each switching period. The accuracy of the calculation of iron loss in the filter inductor by the loss map method was verified with the ILA. We found that the value calculated by the loss map method differed slightly from the value measured with the ILA. However, these differences can be reduced if we take into account the accurate flux density calculation and the effect of the duty ratio of PWM pulses on the loss. Finally, we verified that the loss map method can provide accurate iron loss calculations.