用于电弧检测的电力专用SoC设计

针对传统的电弧电路故障检测结果不准确的问题,设计用于电弧检测的SoC系统,并且在55nm工艺下进行流片验证。采用包含两种结构的模数转换器的片上电压源,设计了锁相环以及复位电路,精度最高可达8.67 bit。验证结果表明,本设计可提高电弧检测的准确性。     

碳酸性侵蚀与AAR作用下纳米混凝土的耐久性

地铁混凝土处于地下空间,容易受到地下水的碳酸性侵蚀；碱集料反应 (AAR)是一种严重的混凝土耐久性问题,既难以发现又难以修补,由两者共同作用引起的混凝土耐久性降低严重影响地铁隧道的正常使用.为研究纳米材料对地铁混凝土在碳酸性侵蚀和AAR共同作用下耐久性的影响,在普通混凝土中掺入适量纳米SiO₂和纳米Fe₂O₃,利用自行研制的碳酸性侵蚀试验箱进行试验,采用碳酸性侵蚀深度、膨胀率和声速作为测试指标来评价纳米混凝土在碳酸性侵蚀和AAR共同作用下的耐久性.试验结果表明:掺入纳米颗粒后,混凝土的膨胀率和侵蚀深度有了明显降低,而声速有了明显提升,说明纳米混凝土的耐久性优于普通混凝土；在182 d龄期时,掺量为2%的纳米SiO₂混凝土耐久性改善最明显,侵蚀深度和膨胀率最小,声速最大且声速下降幅度最小；其次是掺量为1%的纳米Fe₂O₃混凝土.由于纳米颗粒特殊的物理化学性质,改善了混凝土内部的微观结构和孔溶液的化学组成,使碳酸性侵蚀和碱集料反应共同作用下混凝土的耐久性得到了提高.     

计及RSC控制的DFIG短路电流直流分量解析表达

现有文献针对计及转子变流器(RSC)控制的双馈感应风电机组(DFIG)定子短路电流解析表达,将定子磁链当作一阶直流衰减分量或忽略功率外环控制。基于DFIG电压、磁链和RSC控制方程,得到定子电流关于定子电压和定子功率的传递函数,提出定子电流的精确解析表达式。基于RSC内、外环PI参数关系,推导直流分量衰减时间常数和角频率关于PI参数的表达式。分析了RSC内外环PI参数对定子电流直流衰减分量的影响。仿真结果验证了解析表达式的准确性,为PI参数选取和保护装置测量、整定提供依据。     

A new controller for boost dc–dc converters based on a novel sliding surface

ABSTRACT

In this paper, two control schemes for boost converters affected by uncertainties in input voltage and load are proposed. The boost converter dynamics is redefined in terms of new state variables to facilitate the use of a disturbance observer that can estimate matched and unmatched disturbances. A sliding surface, which is new in the context of boost converters, is proposed to enable tracking and regulation of output voltage without requiring measurement of input voltage and load current. The stability of the overall system including the disturbance observer, the sliding variable and the output is proved. The performance of the schemes is assessed for regulation of output voltage and tracking of reference voltage by simulation as well as experimentation in which various types of uncertainties and various types of reference voltages are considered.     

超临界蒸汽参数对燃气蒸汽联合循环性能影响研究

为进一步提高联合循环效率,参考现有燃气蒸汽联合循环12.5 MPa/568℃亚临界蒸汽参数,提出27 MPa/585℃超临界蒸汽参数,根据燃气蒸汽联合循环计算模型,以397 MW燃气轮机联合循环机组为例,计算了超临界蒸汽参数与两种亚临界蒸汽参数的底循环效率和联合循环效率,并分析对比了3种蒸汽参数的底循环效率对联合循环效率的贡献。研究表明:对于同一燃气轮机,超临界和亚临界中低压蒸汽参数不同时,超临界蒸汽参数的底循环效率比亚临界提高了4.3%,蒸汽底循环输出功率占联合循环机组输出功率的百分比由30.21%增加到32.62%,联合循环净效率增加了2.21%,联合循环机组的输出功率增加了20.38 MW;中低压蒸汽参数相同时,超临界蒸汽参数的底循环效率比亚临界提高了2.87%,蒸汽底循环输出功率占联合循环机组输出功率的百分比由31.16%增加到32.62%,联合循环净效率增加了1.44%,联合循环机组的输出功率增加12.5 MW。     

A New Design Methodology for Time-Based Capacitance-to-Digital Converters (T-CDCs)

This paper introduces a 9-bit time-based capacitance-to-digital converter (T-CDC). This T-CDC adopts a new design methodology for parasitic cancellation with a simple calibration technique. In T-CDCs, the input sensor capacitance is first converted into a delay pulse using a capacitance-to-time converter (CTC) circuit; then this delay signal is converted into a digital code through a time-to-digital converter (TDC) circuit. A prototype of the proposed T-CDC is implemented in UMC 0.13 μm CMOS technology. This T-CDC consumes 8.42 μW and achieves a maximum SNR of 45.14 dB with a conversion time of 1 μs that corresponds to a figure of merit (FoM) of 16.4 fJ/Conv.     

Combined constant speed control method for a wind generator equipped with hydraulic energy storage

A wind generator equipped with hydraulic energy storage (WG‐HES) uses hydraulic transmission systems instead of gearbox transmissions, thus eliminating high‐power converters and reducing the tower‐top cabin weight. When there is no wind or the wind speed is extremely low, the pressured oil released by accumulators is used to drive a motor to operate at a constant speed, thereby generating constant‐frequency power. However, few studies have examined the constant speed control characteristics for generating electricity using only an accumulator group. In this study, a combined constant speed (CCS) proportional–integral–derivative (PID) control method based on “variable displacement and throttling” is proposed, which includes two closed loops and one regulating loop. First, a simulation model of the CCS PID control method for a variable motor was established in the Simcenter Amesim program. The influence of different PID parameters on the anti‐interference ability of the constant speed control of the motor was analyzed under a given load step. Then, we obtained the range of control parameter values and a set of optimal values. Second, the effectiveness of the CCS control method and the accuracy of the simulation results were verified on a 600‐kW WG‐HES system prototype. The results verified that the CCS control method has good anti‐interference ability and can meet the requirements of constant speed control for a variable motor under the best PID parameters. These results can provide a basis for developing control strategies for WG‐HESs when there is no wind or at low wind speeds.     

A new design strategy for DC/DC LLC resonant converter: Concept,modeling, and fabrication

In this paper, a new design procedure for LLC converter has been introduced. In fact, this method is a computer-based design algorithm based on a numerical technique. In the process of designing, the value of the resonant element is obtained by solving the LLC converter fundamental equation. This converter will be controlled by using state feedback, such as output voltage variable. As a matter of fact, in a control system, the change of output voltage (because of load variation) will affect the switching frequency, so the output voltage will be tuned. In the designing process, the fundamental equations of LLC converter are obtained, and the value of the resonant elements is calculated. Also, a comparison analysis is carried out between the proposed and typical methods. The simulation is done to investigate the validity of the proposed method. Moreover, a prototype is manufactured, and the experimental test is done to evaluate its applicability.     

Effects of temperature on creepage discharge characteristics in oil-impregnated pressboard insulation under combined AC–DC voltage

Due to the complexity of the valve side winding voltage of the converter transformer, the insulation characteristics of the oil-impregnated pressboard (OIP) of the converter transformer are different from those of the traditional AC transformer. The study on effect of temperature on the creeping discharge characteristics of OIP under combined AC–DC voltage is seriously inadequate. Therefore, this paper investigates the characteristics of OIP creepage discharge under combined AC–DC voltage and discusses the influence of temperature on creepage discharge characteristics under different temperatures from 70°C to 110 °C. The experimental results show that the partial discharge inception voltage and flashover voltage decrease with increasing temperature. The times of low amplitude discharge (LAD) decrease and amplitude of LAD increases. Simultaneously, the times of high amplitude discharge (HAD) gradually increase at each stage of creepage discharge with higher temperature. The analysis indicates that the charge carriers easily accumulate and quickly migrate directional movement along the electric field ahead of discharging. The residual charge carriers are more easily dissipated after discharging. The ‘hump’ region of LAD moves to the direction of higher discharge magnitude. The interval time between two continuous discharges is shortened obviously. The concentration of HAD accelerates the development of OIP insulation creepage discharge. The temperature had an accelerating effect on the development of discharge in the OIP under applying voltage.     

冶金矿物和产品水分测定问题探讨

水分测定是冶金行业中矿产原料和产品分析的重要内容,主要包括交货水分、湿存水、化合水等测定类别。尽管水分测定方法本身相对简单,但其涉及到矿物原料、产品结算交割以及其他化学分析的校正计算,属于重要的基础性测定方法。各类矿物、产品几乎都有相应水分测定的国家标准、行业标准,部分还是从国外ISO标准体系中采标而来。文章系统介绍并比较各类矿物原料、产品中交货水分、明水、湿存水、化合水等类别的测定方法。由于ISO标准体系中湿存水含义和国内标准体系湿存水含义有较大差异,其测定操作和用途也有不同,使用空气平衡样品和密封原始样品将会得到数据差异较大的湿存水数据,两种湿存水含义需要明确区分。湿存水对化学称样量、灼减量、化合水的测定有影响,需要用湿存水进行水分校正,才能得到更精确的结果。