Low threshold voltage,highly stable electroforming-free threshold switching characteristics in VOx films-based device

Threshold switching (TS) devices have evolved as one of the most promising elements in memory circuit due to their important significance in suppressing crosstalk current in the crisscross array structure. However, the issue of high threshold voltage (V_th) and low stability still restricts their potential applications. Herein, the vanadium oxide (VO_x) films deposited by the pulsed laser deposition (PLD) method are adopted as the switching layer to construct the TS devices. The TS devices with Pt/VO_x/Pt/PI structure exhibit non-polar, electroforming-free, and volatile TS characteristics with an ultralow V_th (+0.48 V/−0.48 V). Besides that, the TS devices also demonstrates high stability, without obviously performance degradations after 350 cycles of endurance measurements. Additionally, the transition mechanism is mainly attributed to the synergistic effect of metal-insulator transition of VO₂ and oxygen vacancies. Furthermore, the nonvolatile bipolar resistance switching behaviors can be obtained by changing oxygen pressure during the deposition process for switching films. This work demonstrates that vanadium oxide film is a good candidate as switching layer for applications in the TS devices and opens an avenue for future electronics.     

工艺参数对动态流量控制法挤压弯管应力的影响

采用有限元模拟和实验研究了挤压钛合金弯曲管件。通过实验验证了工件的形状和尺寸精度,并通过有限元模拟分析了工艺参数对挤出过程中变形体的平均压应力分布情况和挤出弯管件的曲率半径的影响规律。结果表明:有限元模拟中,弯管件的曲率半径误差为6.03%,弯管直径误差为3.82%;在靠近定径带处,平均压应力呈非均匀分布;在焊合腔内,靠近细分流孔区域的平均压应力小于靠近粗分流孔区域的平均压应力,平均压应力的大小顺序在通过粗、细分流孔前后相反;在模具结构固定不变时,弯管件的曲率半径随挤压速度的减小而增大,不随挤压温度的变化而变化。     

Nitrate Additives Coordinated with Crown Ether Stabilize Lithium Metal Anodes in Carbonate Electrolyte

Lithium metal anodes (LMAs) are promising for next-generation batteries but have poor compatibility with the widely used carbonate-based electrolytes, which is a major reason for their severe dendrite growth and low Coulombic efficiency (CE). A nitrate additive to the electrolyte is an effective solution, but its low solubility in carbonates is a problem that can be solved using a crown ether, as reported. A rubidium nitrate additive coordinated with 18-crown-6 crown ether stabilizes the LMA in a carbonate electrolyte. The coordination promotes the dissolution of NO₃⁻ ions and helps form a dense solid electrolyte interface that is Li₃N-rich which guides uniform Li deposition. In addition, the Rb (18-crown-6)⁺ complexes are adsorbed on the dendrite tips, shielding them from Li deposition on the dendrite tips. A high CE of 97.1% is achieved with a capacity of 1 mAh cm⁻² in a half cell, much higher than when using the additive-free electrolyte (92.2%). Such an additive is very compatible with a nickel-rich ternary cathode at a high voltage, and the assembled full battery with a cathode material loading up to 10 mg cm⁻² shows an average CE of 99.8% over 200 cycles, indicating a potential for practical use.     

梯度铝蜂窝夹芯板的力学行为

梯度分层铝合金蜂窝板是一种有效的吸能结构,本工作在梯度铝蜂窝结构的基础上根据梯度率的概念,通过改变蜂窝芯层的胞壁长度,设计了4种质量相同、梯度率不同的铝蜂窝夹芯结构。通过准静态压缩实验,并结合非线性有限元模拟准静态及冲击态下梯度铝蜂窝夹芯结构的变形情况及其力学性能,分析对比了相同质量下梯度铝蜂窝夹芯结构在准静态下的变形模式以及冲击载荷下分层均质蜂窝结构和不同梯度率的分层梯度蜂窝结构的动态响应和能量吸收特性。结果表明:在准静态压缩过程中,铝蜂窝梯度夹芯板的变形具有明显的局部化特征,蜂窝芯的变形为低密度优先变形直至密实,层级之间的密实化应变差随芯层密度的增大而逐渐减小;在高速冲击下,梯度蜂窝板并非严格按照准静态过程中逐级变形直至密实,而是在锤头冲击惯性及芯层密度的相互作用下整体发生的线弹性变形、弹性屈曲、塑性坍塌及密实化;另外,在本工作所设计的梯度率中,当梯度率为γ₁=0.0276时,梯度蜂窝夹芯板的吸能性达到最好,相较于同等质量下的均质蜂窝夹芯板,能量吸收提高了10.63%。     

“高电压技术”课程线上线下混合式教学

本文采用超星学习通线上教学平台，以 “高电压技术”课程为对象，实施了规模为120余人的线上线下混合式教学。基于线上教学和传统教学的优势互补，设计了“高电压技术”多个教学环节。归纳分析了混合式教学在各个教学环节取得的效果和问题，并根据学生反馈提出了持续性的改进措施。     

Optimization of PEMFC system operating conditions based on neural network and PSO to achieve the best system performance

PEMFC system is a complex new clean power system. Based on MATLAB/Simulink, this paper develops a system-level dynamic model of PEMFC, including the gas supply system, hydrogen supply system, hydrothermal management system, and electric stack. The neural network fits the electric stack model to the simulation data. The effects of different operating conditions on the PEMFC stack power and system efficiency are analyzed. Combining the power of the reactor and the system efficiency to define the integrated performance index, the particle swarm optimization (PSO) algorithm is introduced to optimize the power density and system efficiency of the PEMFC with multiple objectives. The final optimal operating point increases the power density and system efficiency by 1.33% and 12.8%, respectively, which maximizes the output performance and reduces the parasitic power.     

Influence of applied voltage and conductive material in DIET promotion for methane generation

The utilization of biological-, electrode- and conductive material-mediated direct interspecies electron transfer (DIET) between exoelectrogenic bacteria and methanogenic archaea for enhancing methane productivity is widely reported in the literature. However, two cardinal questions are still controversial, i.e., which applied voltage value would be more recommended to enhance methane generation? and how the DIET over IIET has the upper hand in enhancing methane productivity? Herein, the influence of different applied voltages to promote biological-, conductive- and electrode-mediated DIET was investigated in MEC-AD reactors with conductive material. Polarized bioelectrodes induced electrode-mediated DIET (eDIET) and biological DIET (bDIET), in addition to cDIET (conductive material-mediated DIET), improved the methane yield to 315.40 mL/g COD_r with an applied voltage of 0.9 V. Whereas further increase of applied voltage 1.2 V, lessened methane production efficiency due to high-voltage inhibition and adverse effect on DIET promotion. The anaerobic digestion coupled microbial electrolysis cells with optimal electric potential selectively promotes the DIET through polarized electrodes were confirmed through microbial analysis. As the contribution of DIET increased to 80%, the methane yield increased, and the substrate residue decreased, resulting in a significant improvement in methane production.     

A numerical study of dynamic behaviors of a unitized regenerative fuel cell during gas purging

The gas purging states affect electricity output and energy storage capacity of unitized regenerative fuel cells. In this study, a model of unitized regenerative fuel cell is established. Cell voltages and operating temperatures influences on the dynamic distribution of thermal fluid during purging process and the discharge of residual liquid water in electrolytic cell mode are investigated. The motivation of the present study is better understanding the gas purging characteristics and its effect on reaction behaviors of unitized regenerative fuel cells. Simulation results reveal a significant influence of purging gas temperature on the water flooding and a great effect of operating voltage on the water diffusion. The operating temperature of electrolytic cell model almost has little effect on purging results at different cell temperature and the same purging gas temperature. When the purging gas temperature is changed, higher temperatures of cell and purging gas facilitate liquid water discharging out from the cell regions. In cell water flooding situation, when having large liquid content, the purging gas has little effects on the water expelling process.     

High voltage and self-healing zwitterionic double-network hydrogels as electrolyte for zinc-ion hybrid supercapacitor/battery

The hydrogel electrolyte is an important part of safety and development potential in zinc-based energy storage equipment due to its inherent low mechanical strength and voltage decomposition. However, hydrogel electrolytes possess a reduced working life for zinc dendrites growth and a narrow voltage window. In this study, a hydrogel electrolyte prepares by the zwitterionic monomer [2-(methacryloyloxy)ethyl]dimethyl-(3-sulfopropyl) (MS) and sodium alginate (SA) alleviate these problems. The zwitterionic double-network hydrogel has good mechanical strength, inhibits the growth of zinc dendrites, enhances practicability, greatly increases the voltage window (0–2.4 V), and has self-healing properties to its rich functional groups. The assembled zinc-ion hybrid supercapacitors (ZHSs) have a high-power density of 172.33 W kg^?1 and an energy density of 88.56 Wh·kg^?1 at 0.5 A g^?1. The assembled zinc-ion battery also has good electrochemical performance. Flexible ZHSs and batteries provide power to the timer stably under different bending angles. The zwitterionic double-network hydrogel can be applied to both zinc-based supercapacitors and batteries.     

Acid–base transport model depicting the dynamic pH response of interfacial reactions

Acid–base transport is integral to many important interfacial reactions in various fields of chemistry, but its theoretical foundation is lacked. Herein, a common acid–base transport model is established owing to the success in deriving buffer transport equations. This model is applicable to most buffer systems by flexibly integrating the transport equations in terms of buffer components, and is verified through the model relationships of buffer transport limiting current by using hydrogen evolution reaction experiments. Based on model calculations, two diagram approaches are proposed to depict the dynamic pH response and aid buffer operation optimizations. The model and methods allow us to quantify the rate-limiting effect of acid–base transport on interfacial reactions and to precisely control the effect through medium regulations. Furthermore, the model has laid the foundation of dynamic pH effect on species transformation and process mechanism, which can be of wide interest in the chemistry encompassing interfacial reactions.