Experimental investigation on the invert stability of operating railway tunnels with different drainage systems using 3D printing technology

In recent years, the invert anomalies of operating railway tunnels in water-rich areas occur frequently, which greatly affect the transportation capacity of the railway lines. Tunnel drainage system is a crucial factor to ensure the invert stability by regulating the external water pressure (EWP). By means of a three-dimensional (3D) printing model, this paper experimentally investigates the deformation behavior of the invert for the tunnels with the traditional drainage system (TDS) widely used in China and its optimized drainage system (ODS) with bottom drainage function. Six test groups with a total of 110 test conditions were designed to consider the design factors and environmental factors in engineering practice, including layout of the drainage system, blockage of the drainage system and groundwater level fluctuation. It was found that there are significant differences in the water discharge, EWP and invert stability for the tunnels with the two drainage systems. Even with a dense arrangement of the external blind tubes, TDS was still difficult to eliminate the excessive EWP below the invert, which is the main cause for the invert instability. Blockage of drainage system further increased the invert uplift and aggravated the track irregularity, especially when the blockage degree is more than 50%. However, ODS can prevent these invert anomalies by reasonably controlling the EWP at tunnel bottom. Even when the groundwater level reached 60 m and the blind tubes were fully blocked, the invert stability can still be maintained and the railway track experienced a settlement of only 1.8 mm. Meanwhile, the on-site monitoring under several rainstorms further showed that the average EWP of the invert was controlled within 84 kPa, while the maximum settlement of the track slab was only 0.92 mm, which also was in good agreement with the results of model test.     

接触器触头系统振动机理分析及算法优化

为了解决合闸过程中动、静触头接触引起的振动弹跳问题.本文建立了接触系统的二自由度运动微分方程,并利用遗传算法对交流接触器吸合过程进行优化,同时通过高速摄影实验对接触弹跳的全过程进行了观察和分析.结果表明:理论与实验结果高度一致,铁心在触头分离前发生碰撞,进一步加剧触头弹跳;铁芯弹跳再次碰撞时,触头的弹跳不受影响;在接触器运行过程中,动铁芯的运动会引起系统轻微振动;采用遗传算法优化的接触器触头弹跳时间和最大振幅均减小.研究结果为进一步控制和减小接触弹跳提供了理论依据.     

Pulse-burst laser-based 10kHz Thomson scattering measurements

Thomson scattering(TS),as a popular and reliable diagnostic technique,has successfully measured electron temperatures and electron number densities of plasmas for many years.However,conventional TS techniques using Nd:YAG lasers operate only at tens of hertz.Here,we present the development of a high-repetition-rate TS instrument based on a high-speed,pulse-burst laser system to greatly increase the temporal resolution of measurements.Successful instrument prototype testing was carried out by collecting TS light from laboratory helium and argon plasmas at 10 kHz.Calibration of the instrument detection sensitivity using nitrogen/oxygen rotational Raman scattering signal is also presented.Quantitative electron number densities and electron temperatures of the plasma were acquired at 10 kHz,for stable plasma discharges as,respectively,～0.9 eV and ～5.37×10~(21)m~(-3) for the argon plasma,and ～1eV and ～6.5×1021 m~(-3) for the helium plasma.     

基于Flow-3D的高速水流无压溢洪洞内消能工数值模拟

针对目前高速水流消能形式存在的缺点,基于Flow-3D软件,采用RNGκ-ε模型、Tru-VOF法模拟了无压洞式溢洪道内消能墩附近的水流运动特性,结合洞塞式消能工的消能机理和水工模型试验,对比分析了内消能墩附近的水流流态、流速分布、压强分布、水面线和消能率等。结果表明,在控制断面束窄度的条件下,消能墩附近流态不会影响洞内安全,消能效果较好,消能墩对墩后水流影响距离较短,为在洞内设置多组消能墩提供了依据。研究成果可为类似工程提供参考。     

Enhancing nugget size and weldable current range of ultra-high-strength steel using multi-pulse resistance spot welding

ABSTRACT

This paper presents an innovative approach that uses a pulse-profile to improve the welding quality of CP1180 steel in resistance spot welding process. Three pulses with two cooling times were used in the developed multi-pulse welding (MPW) schedule. The experimental results show that the first pulse increases the contact area between the sheets to improve the current flow pattern. The second pulse was designed to extend the sheet-to-sheet contact area and corona bond for preventing rapid nugget growth. Using these designs, the nugget size was maximised through the third pulse. The maximum nugget size using the designed MPW schedule was 18.5% greater than that of the single-pulse welding schedule and the weldable current range was extended by 130%.     

基于差频检测技术的高速AD单粒子翻转评估方法研究

本文基于差频检测的原理，提出一种在高频动态输入模式下，对高速高精度模数转换器（AD）的抗单粒子翻转效应进行评估的测试方法，并以一款8位3 GSPS高速AD为测试对象，设计开发了一套高速AD单粒子翻转效应测试系统，对目标器件进行了重离子试验。通过对试验结果的图像和错误数据进行分析，评估参试器件的抗辐照性能参数，为抗辐照高速高精度AD的加固设计提供数据支撑。     

超细粉在内循环流化床中的流态化特性

在内径120 mm的半圆柱形内循环流化床中,以平均粒径387 nm的Ti O2为原料,考察了单独通入流化气、射流气和同时通入流化气和射流气三种流化方式下超细粉的流化特性以及射流气速对超细粉聚团尺寸的影响。结果表明:同时通入流化气和射流气时,流化气能促进粉体循环,消除环隙死区;高速射流能有效破碎聚团,显著减小聚团尺寸,从而使超细粉在环隙区与导流管之间形成稳定循环,小聚团在环隙区实现平稳流态化。随着射流气速的增大,聚团尺寸减小,粒度分布变窄,在射流气速分别为60,90,120,150 m/s的条件下,聚团平均直径分别为194,158,147,135μm。     

一款紧凑增强型可变阻抗电磁带隙结构

基于传统AI-EBG结构,提出了一种小尺寸的增强型电磁带隙结构,实现了从0.5~9.4 GHz的宽频带-40 dB噪声抑制深度,且下截止频率减少到数百MHz,可有效抑制多层PCB板间地弹噪声。文中同时研究了EBG结构在高速电路应用时的信号完整性问题,使用差分信号方案可改善信号完整性。     

A Restart Control Method for Position Sensorless PMSM Drive Systems Without Potential Transformer for Railway Vehicle Traction

This paper proposes a restart control method for position sensorless PMSM drive systems without a potential transformer for railway vehicle traction. This method can estimate the initial rotor speed and position under coasting conditions over the entire speed range. The method can also be used when the back‐EMF voltage is higher than the inverter DC link voltage. The proposed method is verified by experiments using a 200‐kW PMSM.     

基于摄影测量的飞机阻力伞运动参数测量技术

针对某型阻力伞性能鉴定试飞科目要求，需要精确测量阻力伞在稳定工作时的垂直、水平摆角，从而为该产品的技术鉴定提供依据。本文根据加装在飞机机背中段的高速摄像机，获取阻力伞的运动影像，通过图像分析处理识别特征点的亚象素坐标，采用摄影测量的解算算法，推导出数学解算模型，实现了阻力伞运动参数的最优解算。结合真实飞行试验对测量结果进行了分析，数据结论准确。