Experimental study on mitigating wind erosion of calcareous desert sand using spray method for microbially induced calcium carbonate precipitation

Wind erosion is one of the significant natural calamities worldwide, which degrades around one-third of global land. The eroded and suspended soil particles in the environment may cause health hazards, i.e. allergies and respiratory diseases, due to the presence of harmful contaminants, bacteria, and pollens. The present study evaluates the feasibility of microbially induced calcium carbonate precipitation (MICP) technique to mitigate wind-induced erosion of calcareous desert sand (Thar desert of Rajasthan province in India). The temperature during biotreatment was kept at 36 °C to stimulate the average temperature of the Thar desert. The spray method was used for bioaugmentation of Sporosarcina (S.) pasteurii and further treatment using chemical solutions. The chemical solution of 0.25 pore volume was sprayed continuously up to 5 d, 10 d, 15 d, and 20 d, using two different concentration ratios of urea and calcium chloride dihydrate viz 2:1 and 1:1. The biotreated samples were subjected to erosion testing (in the wind tunnel) at different wind speeds of 10 m/s, 20 m/s, and 30 m/s. The unconfined compressive strength of the biocemented crust was measured using a pocket penetrometer. The variation in calcite precipitation and microstructure (including the presence of crystalline minerals) of untreated as well as biotreated sand samples were determined through calcimeter, scanning electron microscope (SEM), and energy-dispersive X-ray spectroscope (EDX). The results demonstrated that the erosion of untreated sand increases with an increase in wind speeds. When compared to untreated sand, a lower erosion was observed in all biocemented sand samples, irrespective of treatment condition and wind speed. It was observed that the sample treated with 1:1 cementation solution for up to 5 d, was found to effectively resist erosion at a wind speed of 10 m/s. Moreover, a significant erosion resistance was ascertained in 15 d and 20 d treated samples at higher wind speeds. The calcite content percentage, thickness of crust, bulk density, and surface strength of biocemented sand were enhanced with the increase in treatment duration. The 1:1 concentration ratio of cementation solution was found effective in improving crust thickness and surface strength as compared to 2:1 concentration ratio of cementation solution. The calcite crystals formation was observed in SEM analysis and calcium peaks were observed in EDX analysis for biotreated sand.     

电信运营商云网规划数字化研究和实现

基于电信运营商数字化转型，系统性地提出了数据驱动的云网发展规划体系，以及六大关键数字化能力构建，设计和实现了一种云网规划数字化平台，该平台可用于实现目标网络精细规划、边缘计算精准预测等场景，并探讨了数字孪生在规划领域的应用前景，对运营商推进云网融合战略、推进高质量发展具有指导和参考意义。     

高稳高效海上风电安装平台关键制造技术研究

海上风电作为可再生清洁能源之一,受到世界各国的高度重视与大力发展。我国将海上风电提升至解决能源危机、减缓气候变化、调整能源结构的国家战略高度,到2030年我国单位国内生产总值二氧化碳排放将比2005年下降65%以上,非化石能源占一次能源消费比重将达到25%左右。安装平台不足将是我国海上风电场无法如期建成投产的主要障碍。对自升自航式海上风电安装平台系列高端装备及其设计制造的三大技术难题——腿站立作业易“失稳”、大平台大跨距大倾覆力矩自升易“失控”、高空吊装巨型叶片逾百螺栓精准定位易“失准”,以及焊缝缺陷修复和局部裂纹损伤的激光锻造修复再制造进行了介绍,研制的具有不同规格的系列装备在中国、英国、丹麦、德国等国家的著名海上风电场建设应用情况良好。     

毫米波三维异质异构集成技术的进展与应用

三维异质异构集成技术是实现电子信息系统向着微型化、高效能、高整合、低功耗及低成本方向发展的最重要方法,也是决定信息化平台中微电子和微纳系统领域未来发展的一项核心高技术。文章详细介绍了毫米波频段三维异质异构集成技术的优势、近年来的发展趋势以及面临的挑战。利用硅基MEMS 光敏复合薄膜多层布线工艺可实现异质芯片的低损耗互连,同时三维集成高性能封装滤波器、高辐射效率封装天线等无源元件,还能很好地处理布线间的电磁兼容和芯片间的屏蔽问题。最后介绍了一款新型毫米波三维异质异构集成雷达及其在远距离生命体征探测方面的应用。     

Feasibility study of large-scale mass customization 3D printing framework system with a case study on Nanjing Happy Valley East Gate

At present, the development and implementation of digital transformation are the keys to promoting high-quality industry development. The new digital fabrication method of robotic 3D printing is a research area being studied by many to tackle the issue of the declining productivity of traditional construction methods. Although many studies have been done, most of the current 3D printing projects are facing limitations in terms of scale. In order to bridge the gap, this article proposed a mass customization 3D printing framework system for large-scale projects. This article discusses how mass customization is made possible through the joint operation of the FUROBOT software and 3D printing hardware. By taking the east gate of Nanjing Happy Valley Plaza as a case study, the article demonstrates and studies the feasibility of the large-scale mass customization 3D printing framework system.     

综采工作面巷道内瓦斯分布规律研究

为了研究综采工作面巷道内瓦斯运移规律，摸清瓦斯流动的状态，采用理论分析、数值模拟和现场试验相结合的方法，理论分析得到了工作面风流特性及瓦斯运移规律，数值模拟得到了瓦斯异常释放后工作面瓦斯浓度分布变化情况及工作面正常工作瓦斯浓度分布，然后进行现场试验，试验结果和数值模拟结果相似。研究为工作面瓦斯治理提供了技术支持。     

Structural analysis and optimization of a tethered swept wing for airborne wind energy generation

In this paper, we present an aero‐structural model of a tethered swept wing for airborne wind energy generation. The carbon composite wing has neither fuselage nor actuated aerodynamic control surfaces and is controlled entirely from the ground using three separate tethers. The computational model is efficient enough to be used for weight optimisation at the initial design stage. The main load‐bearing wing component is a nontypical “D”‐shaped wing‐box, which is represented as a slender carbon composite shell and further idealised as a stack of two‐dimensional cross section models arranged along an anisotropic one‐dimensional beam model. This reduced 2+1D finite element model is then combined with a nonlinear vortex step method that determines the aerodynamic load. A bridle model is utilised to calculate the individual forces as a function of the aerodynamic load in the bridle lines that connect the main tether to the wing. The entire computational model is used to explore the influence of the bride on the D‐box structure. Considering a reference D‐box design along with a reference aerodynamic load case, the structural response is analysed for typical bridle configurations. Subsequently, an optimisation of the internal geometry and laminate fibre orientations is carried out using the structural computation models, for a fixed aerodynamic and bridle configuration. Aiming at a minimal weight of the wing structure, we find that for the typical load case of the system, an overall weight savings of approximately 20% can be achieved compared with the initial reference design.     

应用独立分量分析的激光测风雷达湍流频谱分解

针对大型风力发电机机组中常见的脉动湍流、风机尾流与涡流等湍流信号,研究了利用自然梯度下降的独立分量分析方法的湍流频谱分离效果,以区分中心风速与湍流信号,提高风机机组的综合工作效率。首先分析了风机组中常见湍流信号的后向散射与频谱分布特点,然后依据这些特点设计了对应的独立分量分析模型。在仿真结果符合要求的基础上,进行了双目激光雷达天线的风速采集与实际分离效果检测。实验结果表明,在大气折射率结构常数C2n≤10-14同时广义大气常数α≥4的通常情况下,利用双目信号能够分离出一个湍流中心和一个中心风速。对1 s内两个谱峰的波动范围进行统计,获得(2.59±0.05)MHz的中心风速以及(1.22±0.19)MHz的湍流中心估计,且二者的平均信噪比分别为25.93 dB和31.01 dB,能够在获得稳定的中心风速估计的同时得到一个较为稳定的湍流中心估计。     

Designed damping controller for SSSC to improve stability of a hybrid offshore wind farms considering time delay

This paper presents the stability improvement results of hybrid doubly fed induction generator (DFIG)-based and permanent magnet generator (PMG)-based offshore wind farms (OWFs) using a static synchronous series compensator (SSSC). An adaptive-network-based fuzzy inference system (ANFIS) controller of the proposed SSSC is designed to render adequate damping characteristics to the studied system. A frequency-domain approach based on a linearized system model using eigenvalue technique analysis is performed. A time-domain scheme based on a nonlinear system model subject to a three-phase short circuit fault at infinite bus with variations in the signal transmission delays has also been investigated to compare the damping of the studied system in cases of with and without controller. The simulation results with MATLAB/SIMULINK toolbox have been presented. It can be concluded from the simulation results that the proposed SSSC joined with the designed ANFIS damping controller can offer adequate damping performance to the studied hybrid DFIG-based and PMG-based OWFs under severe disturbance.     

Questioning numerical integration methods for microsphere (and microplane) constitutive equations

In the last few years, more and more complex microsphere models have been proposed to predict the mechanical response of various polymers. Similarly than for microplane models, they consist in deriving a one-dimensional force vs. stretch equation and to integrate it over the unit sphere to obtain a three-dimensional constitutive equation. In this context, the focus of authors is laid on the physics of the one-dimensional relationship, but in most of the case the influence of the integration method on the prediction is not investigated.Here we compare three numerical integration schemes: a classical Gaussian scheme, a method based on a regular geometric meshing of the sphere, and an approach based on spherical harmonics. Depending on the method, the number of integration points may vary from 4 to 983,040! Considering simple quantities, i.e. principal (large) strain invariants, it is shown that the integration method must be carefully chosen. Depending on the quantities retained to described the one-dimensional equation and the required error, the performances of the three methods are discussed. Consequences on stress–strain prediction are illustrated with a directional version of the classical Mooney–Rivlin hyperelastic model. Finally, the paper closes with some advices for the development of new microsphere constitutive equations.