Electrophoretic deposition of graphene oxide on carbon brush as bioanode for microbial fuel cell operated with real wastewater

Microbial fuel cell (MFC) is a promising technology for simultaneous wastewater treatment and energy harvesting. The properties of the anode material play a critical role in the performance of the MFC. In this study, graphene oxide was prepared by a modified hummer's method. A thin layer of graphene oxide was incorporated on the carbon brush using an electrophoretic technique. The deoxygenated graphene oxide formed on the surface of the carbon brush (RGO-CB) was investigated as a bio-anode in MFC operated with real wastewater. The performance of the MFC using the RGO-CB was compared with that using plain carbon brush anode (PCB). Results showed that electrophoretic deposition of graphene oxide on the surface of carbon brush significantly enhanced the performance of the MFC, where the power density increased more than 10 times (from 33 mWm^?2 to 381 mWm^?2). Although the COD removal was nearly similar for the two MFCs, i.e., with PCB and RGO-CB; the columbic efficiency significantly increased in the case of RGO-CB anode. The improved performance in the case of the modified electrode was related to the role of the graphene in improving the electron transfer from the microorganism to the anode surface, as confirmed from the electrochemical impedance spectroscopy measurements.     

n-Al2O3P/Ni复合刷镀层的组织和摩擦磨损特性

研究了镍基纳米Al2O3复合电刷镀层（n-Al2O3^p/Ni）的组织特征及擦磨损特性，并与快镍刷镀（Ni)进行了比较。结果表明：n-Al2O3^p/Ni复合刷镀层表面粗糙度更小，组织更致密，镀层摩擦系数随镀液中纳米粒子含量增加稍有增大；n-Al2O3在复合刷镀层中弥散分布，与基相良好结合；复合镀的耐磨性能明显优于Ni刷镀层，镀液中n-Al2O3含量为20g/L时，复合刷镀层具有最佳耐磨性能。     

油田采出水的高温水解-好氧处理工艺研究

根据油田采出水的水质特征，采用厌氧(水解)-好氧(接触氧化)处理工艺。实验表明，虽然油田采出水的BOD5／CODCr，较低，属于难生物降解废水，但是当温度为50～60℃时，选择厌氧停留时间为6h，好氧停留时间为3．5h，气水比为10～20，可使其出水的CODCr稳定在120mg／L左右。如果排除Cl^-产生的影响，CODCr，约为60～70mg／L，达到GB8978-1996一级排放标准。     

太阳能热水器内表面电刷镀锌

用电刷镀的方法,对尺寸为2000mm×1000mm×0.8mm 的 A_3钢板电刷镀锌保护层;并对影响镀锌层质量的因素进行了充分的研究。     

n-Al2O3/Ni复合镀层的组织与滑动磨损性能研究

用电刷镀技术制得了镍基n-Al2O3复合镀层，并对镀层的滑动磨损性能进行了试验研究。纳米复合镀层的表面形貌比较细腻，镀层中纳米粒子分布均匀，与基质金属结合紧密。镀层显微硬度达到HV700，比快速镍镀层提高约40％。滑动磨损试验结果表明，随着纳米粒子含量的增大，镀层的耐磨性提高，摩擦系数也呈增大趋势；但当镀层中n-Al2O3粒子的超过2.56%(质量分数）时，镀层的耐磨性显著下降。纳米复合镀层的磨损机制以疲劳磨损为主，而快速镍底层以粘着磨损为主。     

直流励磁机电刷打火的常见原因及对策

主要介绍了中铝公司山西分公司自备热电厂6台发电机组的励磁机电刷打火的常见原因的分析和处理方法。     

发电机同轴励磁机电刷火花过大的原因及处理方法

本文对发电机同轴励磁机电刷火花过大的原因进行了分析．并针对这些原因提出了相应的处理办法。对规范励磁机的运行维护有很大的帮助。     

DW型单体液压支柱的大修工艺

老煤矿由于资金紧张 ,外购新柱补充很少。因此 ,现使用的单体液压支柱超期服役的较多 ,急需升井大修 ,以满足各矿采煤工作面的需要。采用校直外圆 ,油缸加衬套的大修方法 ,可满足使用要求。     

污水射流曝气工艺技术在聚驱中的应用

为了减少油田污水外排，应用油田采出的污水配制和稀释聚合物溶液，需要对污水进行曝气处理，通过小型试验和现场应用，对应用射流曝气技术处理油田污水的工艺和效果进行了可行性研究和试验，研究表明应用射流曝气技术处理油田污水，可以达到曝氧站的处理效果，经过射流曝气工艺处理的污水所配制和稀释的聚合物溶液粘度能够满足聚合物驱油的注入要求，并且可以大幅度降低地面工程建设投资，取得较好的经济效益和社会效益。     

Modelling of induced aeration in turbine aerators by use of radial basis function neural networks

Gas induction in agitated vessels with turbine impellers can be modelled accurately by means of radial basis function neural nets. The results obtained with the radial basis neural net were significantly better than those obtained by multivariate regression models or standard back propagation neural nets. Moreover, by using the radial basis function neural net model, it was possible to conduct a sensitivity analysis of the variables affecting aeration. Increased medium density showed a strong adverse effect, while variation of the viscosity can cause an increase or a decrease in the rate of aeration, depending on the prevailing process conditions.