铍铜合金断续切削后刀面磨损机理研究

目的研究断续切削过程温度变化对刀具粘结现象、涂层剥落和刀具磨损的影响。方法搭建了仿铣削加工的断续车削实验平台,采用热电偶法测量了断续切削过程中刀具后刀面在不同速度下的切削温度,利用带有能谱仪(EDS)的扫描电镜(SEM)观察后刀面随速度变化的磨损形貌并分析后刀面磨损区域的元素组成,阐述了后刀面温度和刀具磨损之间的联系,研究了Ti AlN涂层硬质合金刀具断续切削铍铜合金C17200时的后刀面磨损机理。结果随着切削速度的增加,刀具温度在v=500 m/min出现峰值,温度越高,后刀面的涂层剥落和粘结磨损现象越严重,涂层剥落和粘结磨损现象在切削速度为500 m/min时最严重,而后随着刀具温度的降低而减缓,切削速度600 m/min时的涂层剥落和粘结磨损现象相比500 m/min时有所减轻。结论断续切削过程中,刀具持续性地经受"负载-卸载"、"升温-降温"产生的高温、冲击和加工环境的不稳定性,是引起粘结现象、涂层剥落和刀具磨损的主要原因。涂层剥落和粘结磨损是导致铍铜合金断续切削刀具失效的主要磨损形式。     

曝气装置结构对多孔板鼓泡特性的影响

气泡体积是决定鼓泡式过滤器性能的重要参数，当使用多孔板作为曝气装置时，孔板结构和气腔状态会对生成气泡体积产生影响。本文采用可视化方法实验研究孔板结构、气腔状态对多孔板鼓泡特性的影响规律。结果表明，气腔无水状态下多孔板鼓泡效果更好；使用有效鼓泡时间能很好地表征多孔板的鼓泡性能；仅当气体流量处于0.35～0.7 L/min、孔间距小于6 mm时，孔间距对多孔板鼓泡性能产生影响；多孔板孔数的确定应保证生成的气泡体积处于气腔控制区。     

Stabilisation of stochastic differential equations driven by G-Brownian motion via aperiodically intermittent control

ABSTRACT

As an emerging field, the G-Itô stochastic calculus plays an important role in describing the model uncertainty. Many interesting works have been done on stochastic differential equations driven by G-Brownian motion (G-SDEs). Among the theories and applications of G-SDEs, the stability is the vital important one. In this paper, we investigate the stabilisation for G-SDEs based on G-Lyapunov function and aperiodically adaptive intermittent controller. As an application, the sufficient conditions are established for the stabilisation of stochastic Cohen–Grossberg neural networks driven by G-Brownian motion (G-SCGNNs). Finally, an example is provided to illustrate the obtained results.     

臭氧氧化-循环喷淋法处理钨钼选矿废水

采用臭氧氧化-循环喷淋法去除钨钼选矿废水中COD,研究了pH值、臭氧流量、循环频率对COD去除效果的影响。结果表明: 废水COD去除率随pH值、臭氧流量、循环频率增大而增加,在pH值为10、臭氧流量3.0 L/min、循环频率4.0次/min条件下,氧化120 min后废水COD含量由131 mg/L降至11.5 mg/L,COD去除率达91.2%,满足《污水综合排放标准》(GB 8978-1996)一级标准。与O₂、NaClO处理废水COD的对比试验结果表明,循环喷淋法结合O₃表现出较好的COD去除效果。     

人工湿地-微生物电解池耦合系统的脱氮特性

实验构建了人工湿地-微生物电解池耦合系统（CW-MEC），并考察了CW-MEC在阴极有无曝气及不同水力停留时间（HRT）的条件下对生活污水的处理效果。实验结果显示，降低HRT会让CW-MEC阴极、阳极的COD去除率由91.11%±7.76%、86.58%±9.54%降低为77.81%±14.84%、81.44%±11.11%，氨氮去除率由58.54%±5.80%、58.22%±5.03%降低为48.04%±12.94%、48.27%±13.40%；阴极增加曝气会让CW-MEC阴极、阳极的COD去除率分别提高到89.51%±3.92%、82.40%±1.63%，阴极氨氮去除率提高到71.51%±16.44%，而阳极氨氮去除率不受影响；增加阴极曝气条件后，系统阴、阳极开始有硝酸盐氮积累，而CW-MEC阴极的硝酸盐氮含量明显低于对照组（CW-MFC）；通过电化学性能分析，相对于CW-MFC系统，CW-MEC具有更低的内阻；通过微生物多样性分析，CW-MEC系统具有更丰富的微生物多样性。     

Probabilistic characterization of the effect of transient stochastic loads on the fatigue-crack nucleation time

The rainflow counting algorithm for material fatigue is both simple to implement and extraordinarily successful for predicting material failure times. However, it neglects memory effects and time-ordering dependence, and therefore runs into difficulties dealing with highly intermittent or transient stochastic loads with heavy tailed distributions. Such loads appear frequently in a wide range of applications in ocean and mechanical engineering, such as wind turbines and offshore structures. In this work we employ the Serebrinsky–Ortiz cohesive envelope model for material fatigue to characterize the effects of load intermittency on the fatigue-crack nucleation time. We first formulate efficient numerical integration schemes, which allow for the direct characterization of the fatigue life in terms of any given load time-series. Subsequently, we consider the case of stochastic intermittent loads with given statistical characteristics. To overcome the need for expensive Monte-Carlo simulations, we formulate the fatigue life as an up-crossing problem of the coherent envelope. Assuming statistical independence for the large intermittent spikes and using probabilistic arguments we derive closed expressions for the up-crossing properties of the coherent envelope and obtain analytical approximations for the probability mass function of the failure time. The analytical expressions are derived directly in terms of the probability density function of the load, as well as the coherent envelope. We examine the accuracy of the analytical approximations and compare the predicted failure time with the standard rainflow algorithm for various loads. Finally, we use the analytical expressions to examine the robustness of the derived probability distribution for the failure time with respect to the coherent envelope geometrical properties.     

AAOA-MBR工艺在工程中的应用分析

通过对AAOA-MBR工艺在实际工程中的应用,分析该工艺处理城市污水的节能减排效能。实践表明AAOA-MBR工艺具有很强的抗冲击负荷能力,在进水质水量大幅度波动、且碳源匮乏的情况下,仍能取得良好的处理效果。实际工程运行四年来,厂区出水各项指标均稳定优于城镇污水处理厂污染物排放标准(GB 18918-2002)中的一级A标准,其中COD、BOD₅、SS、NH₃^-N去除率分别达到可分别达到90.14%、98.25%、95.58%和98.2%;通过对运行期间污水处理量与耗电量相关关系进行回归分析可知,当处理水量达到设计规模时,其吨水耗电量预测为0.31kWh/m³。同时,基于对污水处理系统的沿程水质检测,优化进水水量分配和内循环回流比并进行产水泵联动改造,可进一步提高系统节能减排效果。     

一种新型城镇污水处理一体化间歇曝气生物膜反应器

文中介绍了一种新型城镇污水处理一体化间歇曝气生物膜反应器的工艺系统、技术原理以及实际处理效果,试验结果显示,该工艺对COD、氮、磷均具有良好的去除效果,是一项具有广阔应用前景的新工艺。     

株洲神农城湖水水质保护及净化处理技术提炼

介绍了株洲神农城核心景观区之神农湖的概况;分析了人工湖水质污染的主要原因及其处理措施;提出了神农湖水质保护与净化处理的工程方案。为维护神农湖的景观水质,本工程主要采取以下两个处理措施:一是增加水体的溶解氧量,保持水体的鲜活力;二是采用循环过滤的方式去除浊度污染。