浅谈压力铸造的全自动化生产

近年来,国家对制造业的数字化、网络化、智能化越来越重视,特别是《中国制造2025》的发布,更是促进整个制造业向智能制造迈进,铸造行业也应该紧跟步伐。在传统压力铸造行业中压铸机的加料、取件,切边机的上件、下件,加工机床的上件、下件,都是依靠人来完成,大大制约了行业的发展。本文阐述了压力铸造的全自动化生产,为压力铸造行业的转型升级提供借鉴。     

汽车发动机用AZ91D合金的表面喷涂与性能

采用热喷涂工艺在压铸态AZ91D合金表面制备了Al涂层,研究了热处理温度和保温时间对AZ91/Al涂层界面组织形貌的影响,并对比分析了扩散层的耐腐蚀性能和耐磨性能。结果表明,热处理前Al涂层与基材为机械结合,热处理后Al涂层与AZ91合金基材的界面处可形成冶金结合扩散层,且随着保温时间延长,扩散层厚度不断增加;热处理温度在375 ℃以下时扩散层主要由β-Mg₁₇Al₁₂相构成,375 ℃×8 h热处理后为α-Mg+β-Mg₁₇Al₁₂相,425 ℃×1 h热处理后为γ-Mg₂Al₃和β-Mg₁₇Al₁₂相。AZ91合金基材和扩散层腐蚀电位从高至低顺序为γ>β>α+β>AZ91合金基材,扩散层的腐蚀电流密度均低于AZ91合金基材,阻抗谱图中容抗弧半径从大至小顺序为γ>β>α+β>AZ91合金基材,扩散层的耐腐蚀性能均优于AZ91合金基材;γ、β和α+β扩散层的摩擦稳定性系数都高于AZ91合金基材,而磨损速率和磨痕宽度都要小于AZ91合金基材,其中β扩散层的磨损速率和磨痕宽度最小,具有最佳的抵抗磨损的能力。     

热作模具钢表面激光堆焊耐磨合金层的研究

本文主要通过在H13钢上用大功率CO_2激光束进行堆焊,阐述了激光堆焊工艺变化对堆焊组织和性能的影响,在本试验条件下,得到了高密度弥散金属化合物组织的激光堆焊层,平均硬度为HV800,与基体呈冶金结合,耐磨性比H13模具钢提高149%。     

新世纪我国压铸业与国际接轨的思考

针对中国压铸行业的现状和存在的问题 ,以及当前的机遇和面临的挑战 ,论述了中国压铸工业进入 2 1世纪所面临的新形势及应采取的对策     

浅谈冲压模具的维修要领及常见故障的排除

介绍冲压模具修理和检查各环节的主要工作内容及维修要领 ,列举了常见故障的排除方法 ,通过总结实际生产中的修模经验 ,对缩短修模周期 ,降低成本 ,延长模具寿命有一定的参考价值。。     

超大型材生产经验

对几种超大型材挤压生产的工艺技术、工模具设计、挤压参数控制等过程进行了分析，通过例子总结了挤压生产超大型材的经验及关键技术。     

邻苯二甲酸酯鼓泡生物降解

该课题测试了邻苯二甲酸酯类化合物的鼓泡生物降解行为。结果表明，邻苯二甲酸酯的降解速率常数（kb)与其烷基链长度之间存在良好的相关性，kb=0.0009x^2-0.019x 0.1123，相关系数r=0.9906；浓度超过500mg/L时，邻苯二甲酸二乙酯可抑制自身的生物降解；中间产物邻苯二甲酸浓度超过50mg/L时，也对邻苯二甲酸二乙酯的生物降解有明显的抑制作用。     

Effects of solidification structure on fatigue crack initiation and fatigue strength in Al−Si−Mg cast alloys

Rotating-bending uniaxial fatigue tests and micro-fatigue crack initiation tests were carried out using a permanent mold cast (PMC) and semi-solid die cast (SDC) with Al−7%Si−0.35%Mg composition in order to examine the relationship between solidification structures and fatigue behaviors. The crack length was measured using a replication method. Fatigue strength was improved in SDC, which was almost consistent with the predicted fatigue strength using the size of Si particle cluster. Resistance to fatigue crack initiation and fatigue strength were improved in SDC owing to the finer Si cluster and to higher ultimate tensile strength. Fatigue crack in PMC was preferentially initiated at pores. For SDC, the fatigue crack was initiated at the Si particle/matrix interface, and then sucessively grew along eutectic cell boundaries.     

Failure analysis of a hot extrusion die used for Al-Li alloy processing

Al-Li alloys being developed as lighter, substitutes for conventional high strength Al alloys are to be processed by routine methods. During extrusion of a 8090 Al-Li alloy, the extrusion die container failed causing some alarm. This failed die container was analysed to examine if the failure was caused by interaction of Li diffusing out of Al-Li alloy with the carbides of die steel. The evidence, although not conclusive, is sufficient to exercise caution during such processing.