Investigation of stress fields for non-standard sized glass plates loaded by ring-on-ring

A ring-on-ring (ROR) test is a prevailing test method for evaluating the equi-biaxial strength of glass materials. However, current ROR test standards limit the strength and size of glass to prevent a nonlinear behavior. In this study, the feasibility of ROR testing for non-standard, high-strength glass, such as tempered or ion-exchanged rectangular glass is investigated. To this end, ROR simulation based on theory and experiment is conducted for thirty non-standard glasses with widths of 100–300 mm and aspect ratios of 1.0–2.0. As a result, the maximum measurable stress was about 215.6 MPa for 100 × 200 mm glass and 481.3 MPa for 300 × 600 mm glass with a 3% deviation, which is well above the strength of regular tempered glass. The main purpose of this work is to understand the range of aspect ratio of horizontal and vertical widths of a glass plate that can be evaluated by the standard ROR test.     

汽轮机转子钢断裂韧度试验方法的研究

采用载荷分离法和多试样法对汽轮机某高压转子钢材料在高温下的断裂韧度值进行了测试,讨论了载荷分离法测断裂韧度的可靠性,并与传统的多试样法进行了对比。     

Flame characteristics of premixed H2-air mixtures explosion venting in a spherical container through a duct

The explosion venting duct can effectively reduce the hazard degree of a gas explosion and conduct the venting energy to the safe area. To investigate the flame quantitative propagation law of explosion venting with a duct, the effects of hydrogen fraction and explosion venting duct length on jet flame propagation characteristics of premixed H₂-air mixtures were analyzed through experiment and simulation. The experiment results under initial conditions of room temperature and 1 atm show that when hydrogen fraction was high enough, part of the unburned hydrogen was mixed with air again to reach an ignitable concentration, resulting in the secondary combustion was easier produced and the duration of the secondary flame increased. With the increase of venting duct length, the flame front distance and propagation velocity increased. Meanwhile, the spatial distribution of pressure field and temperature field, and the propagation process and mechanism of the flame venting with a duct were analyzed using FLUENT software. The variation of the pressure wave and the pressure reflection oscillation law in the explosion venting duct was captured. Therefore, in the industrial explosion venting design with a duct, the hazard caused by the coupling of venting pressure and venting flame under different fractions should be considered comprehensively.     

Deposition of UF5 on the surface of steel material having oxide coating in contact with gaseous UF6

When UF6 is handled in leak tight system, the amount of uranium compound formed on the surface of containers, valves, and others in UF6 handling facilities is not so significant for a short term that special attention has not been given to this problem. The present work was done to throw some more light on this problem based on the recent experiment. We discuss the possibility that the intermolecular transfer of a fluorine atom from UF6 to UF5 may participate in the formation of uranium compound. The discussion includes also the unique features contained in the experimental result, the reaction processes assumed in this problem, and the derivation of a rate equation for expressing the deposition of uranium compound. Furthermore, we propose a new method for determining nonlinear parameters included in a governing differential equation having two variables for expressing the deposition of uranium compound from experimental raw data.     

基于组合双向拍卖的云资源调度方法

针对跨数据中心的资源调度问题，提出了一种基于组合双向拍卖（PCDA）的资源调度方案。首先，将云资源拍卖分为三个部分：云用户代理报价、云资源提供商要价、拍卖代理组织拍卖；其次，在定义用户的优先级及任务紧迫度的基础上，在拍卖过程中估算每一个工作发生的服务等级协议（SLA）违规并以此计算云提供商的收益，同时每轮竞拍允许成交多项交易；最终达到根据用户等级合理分配云资源调度的效果。仿真实验结果表明该算法保证了竞拍成功率，与传统一次拍卖成交一项的组合双向拍卖方案相比，PCDA在竞拍时间段产生的能耗降低了35.00%，拍卖云提供商的利润提高了约38.84%。     

Development and validation of a micro-fin tubes evaporator model using R134a and R1234yf as working fluids

This paper presents a model of shell and tube evaporator with micro-fin tubes using R1234yf and R134a. The model developed for this evaporator uses the ε-NTU method to predict the evaporating pressure, the refrigerant outlet enthalpy and the outlet temperature of the secondary fluid. The model accuracy is evaluated using different two-phase flow boiling correlations for micro-fin tubes and comparing predicted and experimental data. The experimental tests were carried out for a wide range of operating conditions using R134a and R1234yf as working fluids. The predicted parameter with maximum deviations, between the predicted and experimental data, is the evaporating pressure. The correlation of Akhavan– Behabadi et al. was used to predict flow boiling heat transfer, with an error on cooling capacity prediction below 5%. Simulations, carried out with this validated model, show that the overall heat transfer coefficient of R1234yf has a maximum decrease of 10% compared with R134a.     

A self‐scalable load injection service

Load testing of applications is an important and costly activity for software provider companies. Classical solutions are very difficult to set up statically, and their cost is prohibitive in terms of both human and hardware resources. Virtualized cloud computing platforms provide new opportunities for stressing an application's scalability, by providing a large range of flexible and less expensive (pay‐per‐use model) computation units. On the basis of these advantages, load testing solutions could be provided on demand in the cloud. This paper describes a Benchmark‐as‐a‐Service solution that automatically scales the load injection platform and facilitates its setup according to load profiles. Our approach is based on: (i) virtualization of the benchmarking platform to create self‐scaling injectors; (ii) online calibration to characterize the injector's capacity and impact on the benched application; and (iii) a provisioning solution to appropriately scale the load injection platform ahead of time. We also report experiments on a benchmark illustrating the benefits of this system in terms of cost and resource reductions. Copyright © 2013 John Wiley & Sons, Ltd.     

Combination of nuclear magnetic resonance spectroscopy and nonlinear methods to analyze the copolymerization of phosphonic acid derivatives

We demonstrate in this study that the combination of modern inline monitoring methods [here: inline nuclear magnetic resonance (NMR)] with simulations gains more exact and profound kinetic results than previously used methods like linearization without that combination. The ¹H-NMR spectroscopic data (more than 100 data points) are used to construct the copolymerization diagram. The reactivity ratios are obtained applying the van Herks nonlinear least square method. The examination of the radical copolymerization of 2-hydroxyethyl methacrylate (HEMA) with (2-{[2-(ethoxycarbonyl)prop-2-en-1-yl]oxy}ethyl) phosphonic acid (ECPPA) as important adhesive monomer used in dentistry yields reactivity ratios of r_HEMA = 1.83; r_ECPPA = 0.42. The copolymerization diagram reflects nonideal, non-azeotropic copolymerization. The sequence distribution of the obtained by Monte Carlo simulation indicates the generation of statistical copolymers. As an important finding, it is demonstrated that the repeating units responsible for etching and adhesion are arranged over the whole polymer chain, which is necessary to achieve proper functionality. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48256.