丁二酸酐酯化改性糯米淀粉的研究

目的 为了提高糯米淀粉的粘度，以达到标签胶的要求。方法 对糯米淀粉进行丁二酸酐酯化改性，通过单因素试验及响应面优化确定出最佳酯化条件，测定其理化性质，并对其进行结构表征。结果 丁二酸酐酯化改性糯米淀粉的最优工艺条件：丁二酸酐添加量（丁二酸酐占淀粉干基的质量百分比）为10.3%，酯化温度为41.5℃，酯化时间为2.0 h,pH为9.0，在此条件下制得的糯米淀粉胶的粘度较高，可达到61.6 Pa·s，且溶解性与溶胀度均有不同程度的提高。电镜与热力学性质分析表明，酯化后淀粉颗粒结晶结构受到破坏，表面粗糙，出现凹陷与裂缝。结论 经过丁二酸酐酯化后，糯米淀粉胶的粘度得到提高。     

MAPP/EAA处理对聚丙烯/小麦秸秆粉复合材料性能的影响

研究了马来酸酐接枝聚丙烯（MAPP）、乙烯丙烯酸共聚物（EAA）处理对聚丙烯（PP） /小麦秸秆粉（WSP）复合材料性能的影响。结果表明，随着体系中MAPP质量份数的增加，PP/WSP的拉伸强度和弯曲强度均逐渐增大，但冲击强度却先增加后减小，复合材料达到塑化峰的时间逐渐延长；使用EAA后，无论体系中是否已经使用了MAPP，PP/WSP的拉伸、弯曲和冲击强度均可得以提高，特别对于未使用MAPP的体系，效果更加明显，可分别提高65.04 %、45.42 %和6.75 %，储能模量增加，表面疏水性增强，平衡扭矩从13.9 N·m降至11.8 N·m，吸水尺寸变化率及吸水率下降，吸水平衡时间缩短；使用EAA可改善PP/WSP中WSP与PP间的界面结合，改善PP/WSP力学性能、热稳定性能、表面疏水性能、尺寸稳定性能和加工性能，降低其吸水率。     

Al-Tolerant Barley Mutant hvatr.g Shows the ATR-Regulated DNA Damage Response to Maleic Acid Hydrazide

ATR, a DNA damage signaling kinase, is required for cell cycle checkpoint regulation and detecting DNA damage caused by genotoxic factors including Al³⁺ ions. We analyzed the function of the HvATR gene in response to chemical clastogen-maleic acid hydrazide (MH). For this purpose, the Al-tolerant barley TILLING mutant hvatr.g was used. We described the effects of MH on the nuclear genome of hvatr.g mutant and its WT parent cv. “Sebastian”, showing that the genotoxic effect measured by TUNEL test and frequency of cells with micronuclei was much stronger in hvatr.g than in WT. MH caused a significant decrease in the mitotic activity of root cells in both genotypes, however this effect was significantly stronger in “Sebastian”. The impact of MH on the roots cell cycle, analyzed using flow cytometry, showed no differences between the mutant and WT.     

Evaluation of maleic acid-based copolymers containing polyoxyethylene ether as inhibitors for CaCO3 scale

Polymer scale inhibitors have been widely used to reduce the loss caused by mineral scaling in circulating cooling water systems. In this article, four maleic acid-based copolymers [hydrolyzed polymaleic anhydride (HPMA)-AEO] containing different fatty alcohol polyoxyethylene ether (such as AEO-9, AEO-10, AEO-15, and AEO-20) are prepared by the way of free-radical copolymerization and characterized using Fourier transform infrared (FTIR), ¹H NMR, and gel permeation chromatographic (GPC) techniques. The effects of HPMA-AEO on CaCO₃ scale are studied in several aspects (such as dose, Ca²⁺ concentration, temperature, inhibition time, pH, the ratio of EO:carboxyl, and the relative supersaturation of CaCO₃ solution) by static experiments. The CaCO₃ scaling process with dosing of HPMA-AEO-9 is investigated under dynamic tests. CaCO₃ deposits and precipitate in the presence of HPMA-AEO-9 are analyzed using scanning electronic microscope (SEM) and X-ray diffraction (XRD). The results show that the performance of HPMA-AEO against CaCO₃ scale highly depends upon the ratio of EO:carboxyl; the introduction of AEO group can significantly improve the performance of HPMA-AEO to tolerate high alkalinity, high hardness, and high temperature; the presence of HPMA-AEO-9 can obviously affect the CaCO₃ scaling process on the tube wall through interfering with nucleation process and crystal growth process and significantly alter the surface morphology and crystal form of CaCO₃ deposits. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47470     

用气相色谱法检测顺酐生产中间物料组分

顺酐在常温下是固体,要制备成溶液才能进行气相色谱分析,所以溶剂的选择极为重要。为此,选用了稳定性好、沸点较高的乙腈作为溶剂,利用超声溶解,对生产中粗酐样品进行采样分析,并建立了气相色谱法测定顺酐中杂质含量的分析方法,可有效指导顺酐生产过程中的杂质组分分离,适用于顺酐生产的现场工艺控制。     

马来酸酐改性腰果壳油对丁苯橡胶性能的影响

以马来酸酐接枝共聚改性环氧基腰果壳油(M-CNSL)作为反应性增塑剂,研究M-CNSL用量对丁苯橡胶(SBR)硫化特性、物理性能和耐热空气老化性能的影响,并与芳烃油和未改性腰果壳油(CNSL)进行对比试验。结果表明:不同增塑剂对SBR的增塑作用从大到小依次为CNSL、芳烃油、M-CNSL,而其硫化胶的耐热空气老化性能没有明显差别;加入CNSL的SBR胶料焦烧时间和正硫化时间显著延长,硫化胶硬度、100%定伸应力较小,拉断伸长率较大;在0~25份用量范围内,添加CNSL或M-CNSL的硫化胶拉伸强度和撕裂强度均出现一个最大值,而添加芳烃油的硫化胶拉伸强度和撕裂强度随着增塑剂用量的增大而减小。硫化胶拉伸断面扫描电镜分析结果表明,M-CNSL的加入有利于白炭黑在胶料中的分散,起到了相容作用。     

脂肪族环氧四丙烯酸酯的合成及其在UV涂料中的应用

采用丁二酸酐、三羟甲基丙烷二丙烯酸酯在催化剂的作用下进行开环反应得中间体,然后再与新戊二醇二缩水甘油醚反应制得脂肪族环氧四丙烯酸酯,并且对其在UV涂料中的应用性能进行了研究。     

以酯基为连接基的非离子双子表面活性剂的合成

以蓖麻油酸（RA）、聚乙二醇（600）为原料,马来酸酐为连接基,合成了一种新型的非离子双子表面活性剂MARAPEG-15,考察了催化剂用量、物料摩尔配比、反应时间及温度对酸酐与蓖麻油酸聚乙二醇硼酸酯酯化的影响,并测定了产物的临界胶束浓度和表面张力。马来酸酐与蓖麻油酸聚乙二醇硼酸酯酯化较佳的工艺条件为：催化剂用量为总质量的3%,n（酸酐）∶n（蓖麻油酸聚乙二醇硼酸酯）为3.1∶2,反应温度为110℃,时间为4 h;硼酸酯键水解时间为1.5 h。产物的表面张力及其临界胶束浓度为γCMC=35.73 mN/m,CMC=1.96×10-5mol/L。