Hydrophobizing polyether sulfone membrane by sol-gel for water desalination using air gap membrane distillation

ABSTRACT

The hydrophobic polyether sulfone membranes were prepared by the sol-gel method to be applied in an air gap membrane distillation setup for desalination. The surface modifications were carried out using Trimethylsilyl chloride (TMSCl) and Methyltrimethoxysilane (MTMS) solutions. The membranes were characterized using Attenuated Total Reflection Infrared (ATR-IR) spectroscopy, Scanning Electron Microscopy (SEM), and Optical Contact Angle (OCA) methods. The effects of membrane preparation as well as operating conditions such as temperature difference, salt concentration, feed rotation speed, and cold-side temperature on membrane performance were investigated using central composite design method. It was found that feed temperature has the largest effect among the parameters on the permeation flux. The flow rate and salt rejection of the membrane in the optimum conditions were 4.47 Kg m^?2 h^?1 and 99.37%, respectively.     

温度对核电站传热管阵列声透射特性的影响

为了研究温度分布对于管阵列结构中的声透射特性的影响，以核电站的实际工况为背景，构建了不同的温度场以及周期性变化的非均匀温度场，利用有限元方法进行数值模拟。结果表明：（1）温度分布会改变管阵列声透射频谱的“禁带”宽度以及中心频率位置。在同一介质中，温度变化对频率较高位置的影响大于频率较低的位置。（2）在同样为10℃的温度差下，当水的平均声速为1 653 m·s^-1、饱和水蒸气的平均声速为522.5 m·s^-1时，介质为水时的禁带宽度及中心频率位置变化较大，即声速大的介质的频谱对于温度的变化更敏感。（3）当温度差在10℃以内，在周期性变化的非均匀温度场和与均匀温度场中管阵列声透射特性在第一中心频率23 996.1 Hz之前，两频谱差别很小，在第一禁带之后会出现明显区别。该研究成果对完善核电站应用的声学检测提供了理论基础。     

Effect of slot-die configurations on coating gap dependence of maximum and minimum wet thicknesses

The dependence of the maximum and minimum wet thicknesses on the coating gap is derived for the slot-die coating process, under different slot-die configurations. Analytical expressions for the wet thickness and its derivative with respect to the coating gap are obtained using a simple flow model. The results indicate that, as expected, the minimum wet thickness increases linearly with the coating gap; however, the maximum wet thickness demonstrates a counterintuitive trend of decreasing as the coating gap increases, when a specific slot-die configuration is assumed. Moreover, the results are also validated by numerically solving the complete two-dimensional (2D) Navier–Stokes equation.     

Influence of Al3+ doping for V5+ on the structural,optical, thermal and electrical properties of V2-xAlxO5-δ (x=0–0.20) ceramics

This paper reports an investigation on the structure-properties correlation of trivalent metal oxide (Al₂O₃)-doped V₂O₅ ceramics synthesized by the melt-quench technique. XRD patterns confirmed a single orthorhombic V₂O₅ phase formation with increasing strain on the doping of Al₂O₃ in place of V₂O₅ in the samples estimated by Williamson-Hall analysis. FTIR and Raman investigations revealed a structural change as [VO₅] polyhedra converts into [VO₄] polyhedra on the doping of Al₂O₃ into V₂O₅. The optical band gap was found in a wide semiconductor range as confirmed by UV–visible spectroscopy analysis. The thermal and conductivity behavior of the prepared samples were studied using thermal gravimetric analysis (TGA) and impedance analyzer, respectively. All the prepared ceramics exhibit good DC conductivity (0.22–0.36 Sm^-1) at 400 ?C. These materials can be considered for intermediate temperature solid oxide fuel cell (IT-SOFC)/battery applications due to their good conductivity and good thermal stability.     

Impact of bismuth oxide on the structure,optical features and ligand field parameters of borosilicate glasses doped with nickel oxide

Understanding the impact of bismuth cations on the optical properties of borosilicate glass is significant for manipulating borate glass applications. In this paper, the influence of bismuth cations on both structural and optical properties of borosilicate glass doped with NiO was investigated. Different glass samples, containing different amounts of Bi₂O₃ and a constant amount of NiO, were prepared and studied. Infrared (IR) analysis was carried out to study the internal structure within the investigated glass samples. Optical absorption studies were performed to investigate the impact of Bi₂O₃ content on optical properties of the BiBaNiB-glasses. Astonishingly, with Bi₂O₃ addition, an absorption band at 380 nm has appeared. Moreover, this band is overlapped with the Urbach edge; which regularly produced an artificial edge-like feature at ~450 nm. A detailed deconvolution protocol has been implemented for an appropriate understanding of these spectra and unraveling the hidden Urbach edge. Optical band gap energy, linear and nonlinear refractive index for each BiBaNiB sample were calculated. Furthermore, the metallization criterion was calculated to examine the metallic or insulating nature of the BiBaNiB-glasses. The values of the nonlinear third-order susceptibility and nonlinear refractive index were increased with Bi₂O₃ doping. The BiBaNiB-glasses exhibited outstanding stability and optical band gap than the pristine glass sample, which makes it possible for practical applications.     

Uniform α-Fe2O3 nanoparticles with narrow gap immobilized on CNTs through N-doped carbon as high-performance lithium-ion batteries anode

Fe₂O₃ with high theoretical capacity, low cost, and environmental friendliness has been attracted great attention in lithium-ion batteries (LIBs), which however is limited by low rate capability and fast capacity fading owing to low electronic conductivity, self-aggregation, and sever volume expansion. CNTs with excellent conductivity and unique 3D interconnected network are ideal matrices for composite electrochemical materials, but it is difficult to meet the demand of high capacity. Here, uniform α-Fe₂O₃ nanoparticles with narrow gap (~1.4 nm) were immobilized on CNTs through N-doped carbon (α-Fe₂O₃/CNTs-NC) that can address these issues. As an advanced LIBs anode, the electrode displays unprecedented specific capacity (1173 mAh/g at 0.2 A/g) and outstanding rate behavior (716.4 mAh/g at 5.0 A/g after 1200 cycles), which are even superior to the theoretical capacity (1007 mAh/g) and the performance of most reported Fe₂O₃-based anodes. Homogeneous nano-sized α-Fe₂O₃ with a narrow gap highly shortens the diffusion path for Li⁺ transport, exposes quite sufficient active sites, and prevents the volume change. Moreover, the 3D backbone of CNTs with a more homogeneously distributed electric field can enhance conductivity, and tightly contact with α-Fe₂O₃ by NC, then obtain robust structural stability, which boosts LIBs in storage capacity, rate capability, and cycling stability.     

基于用户体验的压路机操纵手柄交互品质研究

目的以压路机操纵手柄为对象,探讨交互品质研究方法,改进用户体验。方法对交互品质进行解析,由用户体验与交互品质的关联性,提出基于用户体验的交互品质研究方法;面向压路机操纵手柄典型任务进行用户体验研究,梳理压路机手柄的操作流程,并对交互行为进行聚类分析,结合语义分析构建用户体验词库,运用半结构式访谈与问卷调查,以定量与定性方法相结合对驾驶员的操纵体验进行调研;以专家研讨的形式进行驾驶员的操纵体验向交互特征的映射,构建交互特征集,进而对操纵手柄的交互品质进行分析与阐释。结果得出了压路机操纵手柄的交互特征与交互品质。结论通过用户体验可以映射交互特征,得到了交互品质,对于从交互品质的角度指导交互设计提供了借鉴。     

Urothelium-Specific Deletion of Connexin43 in the Mouse Urinary Bladder Alters Distension-Induced ATP Release and Voiding Behavior

Connexin43 (Cx43), the main gap junction and hemichannel forming protein in the urinary bladder, participates in the regulation of bladder motor and sensory functions and has been reported as an important modulator of day–night variations in functional bladder capacity. However, because Cx43 is expressed throughout the bladder, the actual role played by the detrusor and the urothelial Cx43 is still unknown. For this purpose, we generated urothelium-specific Cx43 knockout (uCx43KO) mice using Cre-LoxP system. We evaluated the day–night micturition pattern and the urothelial Cx43 hemichannel function of the uCx43KO mice by measuring luminal ATP release after bladder distention. In wild-type (WT) mice, distention-induced ATP release was elevated, and functional bladder capacity was decreased in the animals’ active phase (nighttime) when Cx43 expression was also high compared to levels measured in the sleep phase (daytime). These day–night differences in urothelial ATP release and functional bladder capacity were attenuated in uCx43KO mice that, in the active phase, displayed lower ATP release and higher functional bladder capacity than WT mice. These findings indicate that urothelial Cx43 mediated ATP signaling and coordination of urothelial activity are essential for proper perception and regulation of responses to bladder distension in the animals’ awake, active phase.     

Characterization of Bi2O3 thin films for doping photoluminescent Er3+ ions

Undoped and Er³⁺-doped Bi₂O₃ thin films were sputter-deposited on Si(100) substrates. Sufficiently oxidized Bi₂O₃ films with refractive indices between 2.17?2.23 were obtained at a wavelength of 633 nm; these values are comparable to those of bulk Bi₂O₃ crystals. While the film composition was stable for deposition temperatures between room temperature (RT) and 450 °C, the refractive index steeply decreased above 450 °C and reached 1.4 at 600 °C. The lowering of the optical transmittance spectra indicated aggregation of metallic Bi and darkening of the film. All films exhibited X-ray diffraction patterns of α-Bi₂O₃. The direct and indirect bandgap energies derived from the Tauc plots were 3.4–3.7 eV and 1.9–2.5 eV, respectively, depending on the O₂ flow rate and deposition temperature. Upon excitation of Er³⁺-doped Bi₂O₃ films at 532 nm, Er³⁺ emissions peaking at 1537 and 1541 nm appeared, and the photoluminescence spectra included fine structures reflecting crystal-field splitting. Resonant excitation of Er³⁺ 4f levels and indirect excitation via the defect levels of Bi₂O₃ followed by energy transfer to Er³⁺ contributed to the emission. The films deposited at RT with Er concentrations of 2 at.% had the emission intensity of Er³⁺, but concentration quenching strongly suppressed the Er³⁺ emission because the doped Er³⁺ ions stayed inside the Bi₂O₃ crystals. At deposition temperatures above 400 °C, the concentration quenching was mitigated possibly because out-diffusion of Er³⁺ ions reduced the effective number of Er³⁺ ions in the Bi₂O₃ crystalline domains.     

Structural,electrical, and linear/nonlinear optical characteristics of thermally evaporated molybdenum oxide thin films

Homogeneous thin films of Molybdenum oxide (MoO₃) were grown on quartz and glass substrates using the thermal evaporation method. XRD results showed that the MoO₃ powder has a polycrystalline structure with an orthorhombic crystal system whereas the MoO₃ thin films have amorphous nature. SEM images showed that the MoO₃ thin films have a nearly uniform surfaces with worm-like shape grains. The film thickness influences on the linear and nonlinear optical characteristics of MoO₃ thin films that were examined using spectrophotometric measurements and from which, the linear optical constants of the MoO₃ thin films were estimated. The electronic transition type was determined as a direct allowed one. The values of the optical band gap were obtained to be in the range of 3.88–3.72 eV. The dispersion parameters, third-order nonlinear optical susceptibility, and the nonlinear refractive index of the MoO₃ thin films were determined and interpreted in the light of the single oscillator model. The temperature dependence of the DC electrical conductivity and the corresponding conduction mechanism for the MoO₃ films were investigated at temperatures ranging from 303 to 463 K.