优化作业方式提高始极片质量

针对某厂铜电解种板工序存在的始极片质量波动较大的问题,从种板系统体积控制和添加剂匹配的角度出发,分析各种因素对始极片质量的影响,做出了相应的改进措施,使种板系统运行更加稳定,始极片质量得到进一步提升。     

轧制与退火对T9S钛合金板材组织与性能的影响

研究了轧制变形量及退火温度对T9S钛合金板材显微组织和室温力学性能的影响。结果表明:增加成品轧制变形量,板材组织破碎更充分,退火后形成等轴α相、拉长α相和晶间β相组织形貌,变形流线比较明显,板材室温强度和硬度升高,伸长率降低,弹性模量增加。随着退火温度升高,板材室温强度和硬度逐渐降低,伸长率逐渐提高,横向弹性模量逐渐减小,纵向弹性模量先增加后减小。经(750~790) ℃×45 min空冷退火处理后的板材可以获得较好的强度和塑性的匹配。     

Cell Sheet Comprised of Mesenchymal Stromal Cells Overexpressing Stem Cell Factor Promotes Epicardium Activation and Heart Function Improvement in a Rat Model of Myocardium Infarction

Cell therapy of the post-infarcted myocardium is still far from clinical use. Poor survival of transplanted cells, insufficient regeneration, and replacement of the damaged tissue limit the potential of currently available cell-based techniques. In this study, we generated a multilayered construct from adipose-derived mesenchymal stromal cells (MSCs) modified to secrete stem cell factor, SCF. In a rat model of myocardium infarction, we show that transplantation of SCF producing cell sheet induced activation of the epicardium and promoted the accumulation of c-kit positive cells in ischemic muscle. Morphometry showed the reduction of infarct size (16%) and a left ventricle expansion index (0.12) in the treatment group compared to controls (24–28%; 0.17–0.32). The ratio of viable myocardium was more than 1.5-fold higher, reaching 49% compared to the control (28%) or unmodified cell sheet group (30%). Finally, by day 30 after myocardium infarction, SCF-producing cell sheet transplantation increased left ventricle ejection fraction from 37% in the control sham-operated group to 53%. Our results suggest that, combining the genetic modification of MSCs and their assembly into a multilayered construct, we can provide prolonged pleiotropic effects to the damaged heart, induce endogenous regenerative processes, and improve cardiac function.     

Bulging in incremental sheet forming of cold bonded multi-layered Cu clad sheet: Influence of forming conditions and bending

Bulge is a defect that causes geometrical inaccuracy and premature failure in the innovative incremental sheet forming (ISF) process. This study has two-fold objectives: (1) knowing the bulging behavior of a Cu clad tri-layered steel sheet as a function of forming conditions, and (2) analyzing the bending effect on bulging in an attempt to identify the associated mechanism. A series of ISF tests and bending analysis are performed to realize these objectives. From the cause-effect analysis, it is found that bulge formation in the layered sheet is sensitive to forming conditions in a way that bulging can be minimized utilizing annealed material and performing ISF with larger tool diameter and step size. The bending under tension analysis reveals that the formation of bulge is an outgrowth of bending moment that the forming tool applies on the sheet during ISF. Furthermore, the magnitude of bending moment depending upon the forming conditions varies from 0.046 to 10.24 N·m/m and causes a corresponding change in the mean bulge height from 0.07 to 0.91 mm. The bending moment governs bulging in layered sheet through a linear law. These findings lead to a conclusion that the bulge defect can be overcome by controlling the bending moment and the formula proposed can be helpful in this regards.     

轧制始极片

本文介绍了轧制法生产始极片的工艺，比较了轧制法和传统的钛种板生产始极片的优缺点，讨论了采用轧制始极片的经济效益和应用前景。     

透明聚丙烯片材专用料研究

研究透明成核剂对均聚PP透明性能的影响。试验表明加入透明成核剂后,提高了PP的透光率,降低了雾度,力学性能得到了明显的改善,添加0.2%透明剂在160~230℃加工条件下生产的专用料,可以制得透明PP片材。     

硅钢片模具设计及其线切割加工

论述了电磁铁铁芯 (硅钢片 )模具的设计要点及其线切割加工的技巧 ,提出了提高模具加工精度和使用寿命的有效措施。     

Structural acrylic adhesives for the sheet steel fabrication industries

Recent developments in rubber-toughened structural acrylic adhesives now offer sheet steel fabricators the opportunity to replace conventional metal fastening techniques such as spot welding with lower cost, durable, more versatile structural adhesive bonding. These developments, in particular much improved ability to bond oily/waxy surfaces common to the motor car industry and improved retention of fracture toughness after exposure to paint stoving temperatures, are discussed in this paper.     

5754-H34铝合金板材生产工艺研究

研究了不同冷变形程度，退火温度对5754铝合金冷轧板材的组织和力学性能的影响，确定了5754合金H34状态板材的生产工艺参数，即冷变形程度25%-45￥，稳定化退火温度120-160℃，保温时间3-6h，在工业生产条件下，其产品的技术指标达到了用户要求。     

橡胶卷材挤出连续硫化生产线的结构特色与工作原理

介绍了橡胶防水防腐卷材挤出连续硫化生产线的结构、特点和工作原理;指出在目前国内同类设备中,该生产设备具有先进性,并可替代引进设备。