Analysis and proposition of limiting current density measurement protocol

Limiting current density at different temperatures, backpressures, and balance gases can be used to separate molecular diffusion resistance, Knudsen diffusion resistance and local transport resistance of membrane electrode assembly (MEA). However, the measurement of limiting current density has no unified protocol. The diverse choices in the literature, either in the control of current or voltage or in the atmosphere like relative humidity and O₂ concentrations, make it difficult to compare the results and identify the true bottleneck hindering the mass transport. In this work, the current-voltage curves obtained by current scanning/stepping and voltage scanning/stepping methods under dilute O₂ of different concentrations and a wide range of relative humidity were measured and analyzed systematically. It is found that the voltage stepping method is superior to the other three ways of control for the reliable determination of the limiting current density. Aided with simultaneous electrochemical impedance spectroscopy measurement, the limiting current density can be determined with pinpoint accuracy. When the limiting current density is just used to qualitatively evaluate different MEA, the voltage scanning method can be used instead for its high time efficiency. The selection of the atmosphere also plays an important role in suppressing the distortion from excessive water and reducing the spurious contribution from proton conduction resistance. It is found that O₂ concentrations at 0.5 vol% and relative humidity at 90% can give the best estimation of O₂ transport resistance in membrane electrode assembly.     

Photomemory and Pulse Monitoring Featured Solution-Processed Near-Infrared Graphene/Organic Phototransistor with Detectivity of 2.4 × 1013 Jones

Emerging graphene/organic phototransistors are eye-catching technologies owing to their unique merits including easy/low-cost fabrication, temperature independent, and achieving various functions. However, their development in the near-infrared (NIR) region is experiencing a bottleneck of inferior sensitivity due to low exciton dissociation efficiency and inefficient charge extraction rate. Here, a novel-design solution-processed graphene/organic NIR phototransistor is reported, that is, creatively introducing electron extraction layer of ZnO on graphene channel and employing organic ternary bulk heterojunction as photosensitive layer, successfully breaking that bottleneck. The phototransistor exhibits a high responsivity of 6.1 × 10⁶ A W⁻¹, a superior detectivity of 2.4 × 10¹³ Jones, and a remarkable minimum detection power of 1.75 nW cm⁻² under 850 nm radiation. Considering its excellent NIR detection performance, a noncontact transmission-type pulse monitoring is carried out with no external circuit support, from which human pulse signal and heart rate can be displayed in real time. The phototransistor, interestingly, can be switched into a photomemory function with a retention time of 1000 s in the atmosphere through a gate voltage of −20 V. The design takes the characteristics of graphene/organic phototransistors to a higher level, beyond the limit of sensitivity, and opens up a novel approach for developing multifunction devices.     

Microcrack healing in zirconia ceramics under a DC electric field/current

Flash event caused by a DC electric field/current was applied to the crack healing in 8 mol % Y₂O₃ stabilized cubic ZrO₂ polycrystals (8Y-CSZ). The flash event, which occurred by applying the DC power higher than a critical value of 100 mW/mm³, successfully healed the microcrack within several minutes without any healing agents at a furnace temperature of 800 °C. As compared to the healing treatment under static annealing, the healing phenomena were accelerated about 2 times under the flash treatment even at the same temperatures, suggesting that the enhanced healing phenomena cannot be explained only by the temperature effect. Since the rate of grain growth was accelerated under the flash treatment, the flash healing would be accelerated through the current-enhanced diffusional processes. This study shows for the first time that the flash event has a potential to apply to the crack healing process in the ceramic materials and composites.     

FeOOH–CoS composite catalyst with high catalytic performances for oxygen evolution reaction at high current density

Water electrolysis is an efficient approach for high-purity hydrogen production. However, the anodic sluggish oxygen evolution reaction (OER) always needs high overpotential and thus brings about superfluous electricity cost of water electrolysis. Therefore, exploiting highly efficient OER electrocatalysts with small overpotential especially at high current density will undoubtedly boost the development of industrial water electrolysis. Herein, we used a simple hydrothermal method to prepare a novel FeOOH–CoS nanocomposite on nickel foam (NF). The as-prepared FeOOH–CoS/NF catalyst displays an excellent OER performance with extremely low overpotentials of 306 and 329 mV at 500 and 1000 mA cm⁻² in 1.0 M KOH, respectively. In addition, the FeOOH–CoS/NF catalyst can maintain excellent catalytic stability for more than 50 h, and the OER catalytic activity shows almost no attenuation no matter after 1000 repeated CV cycles or 50 h of stability test. The high catalytic activity and stability have exceeded most non-noble metal electrocatalysts reported in literature, which makes the FeOOH–CoS/NF composite catalyst have promising applications in the industrial water electrolysis.     

Influence of anode current density on carbon parasitic reactions during electrolysis

In the electro-deoxidation process, carbon parasitic reaction (CO₃^2- + 4e^-=C + 3O^2-) usually occurs when using carbon materials as the anode, which leads to increase of the carbon content in the final metal and decrease of the current efficiency of the process. The aim of this work is to reduce the negative effect of carbon parasitic reaction on the electrolysis process by adjusting anode current density. The results indicate that lower graphite anode area can achieve higher current density, which is helpful to increase the nucleation site of CO₂ bubbles. Most of CO₂ would be released from the anode instead of dissolution in the molten CaCl₂ and reacting with O^2- to form CO₃^2-, thus decreasing the carbon parasitic reaction of the process. Furthermore, the results of the compared experiments show that when the anode area decreases from 172.78 to 4.99 cm², CO₂ concentration in the released gases increases significantly, the carbon mass content in the final metal product decreased from 1.09% to 0.13%, and the current efficiency increased from 6.65% to 36.50%. This study determined a suitable anode current density range for reducing carbon parasitic reaction and provides a valuable reference for the selection of the anode in the electrolysis process.     

Contribution of metal vapor mass at periphery part of pulsed arc to electromagnetic force in weld pool

The arc welding has been used in various welding methods because it is inexpensive and high in strength after welding. However, it is a problem that accidents such as collapse of the bridge occur because of the welding defects. The welding of low cost and high productivity is required without the welding defects. The pulsed TIG welding is inexpensive and capable of high‐quality welding. The electromagnetic force contributing to penetration changes because the transient response of arc temperature and iron vapor generated from anode occurs. However, the analysis of pulsed TIG welding with metal vapor has been elucidated only metal vapor concentration near anode with transient phenomenon and heat flux. Thus, the theoretical elucidation of penetration depth with control factor has not been researched. In this paper, the contribution of metal vapor mass at the periphery part of pulsed arc to the electromagnetic force in the weld pool is elucidated. As a result, the iron vapor mass at periphery part decreased with increasing the frequency. The iron vapor was stagnated at axial center within one cycle. The electromagnetic force to the penetration depth direction in weld pool increased at axial center. Therefore, the metal vapor mass at periphery part plays an important role for the electromagnetic force increment at axial center.     

Microstructure,tribological behavior and magnetic properties of Fe−Ni−TiO2 composite coatings synthesized via pulse frequency variation

The Fe−Ni−TiO₂ nanocomposite coatings were electrodeposited by pulse frequency variation. The results showed that the nanocomposite with a very dense coating surface and a nanocrystalline structure was produced at higher frequencies. By increasing the pulse frequency from 10 to 500 Hz, the iron and TiO₂ nanoparticles contentswere increased in expense of nickel content. XRD patterns showed that by increasing the frequency to 500 Hz, an enhancement ofBCC phase was observed and the grain size of deposits was reduced to 35 nm. The microhardness and the surface roughness were increased to 647 HV and 125 nm at 500 Hz due to the grain size reduction and higher incorporation of TiO₂ nanoparticles into the Fe−Ni matrix (5.13 wt.%). Moreover, the friction coefficient and wear rate values were decreased by increasing the pulse frequency;while the saturation magnetization and coercivity values of the composite deposits were increased.     

脉冲激光与电弧布置方式对铝合金焊接熔滴过渡与焊缝形貌的影响

以2219铝合金为基板，研究了不同脉冲激光-电弧布置方式下的熔滴过渡与焊缝形貌特征，分析了熔深增加的机理. 结果表明，当脉冲激光照射母材时，脉冲激光主要提供对母材的热输入，母材温度的增加有助于促进熔滴铺展，稳定熔滴过渡过程；当脉冲激光照射熔滴缩颈时，主要提供对熔滴的力输入，蒸发反力的作用下形成"一脉一滴"，显著提高熔滴过渡频率与熔滴飞行速度，增加了熔滴对熔池的冲击力，熔深增加；当脉冲激光交替的照射熔池和熔滴时，一方面能够对母材进行加热，有助于熔滴的铺展，另一方面能够提高熔滴过渡频率，提高焊缝的均匀性.