Diluted chemical bath deposition of CdZnS as prospective buffer layer in CIGS solar cell

In this study, dilute chemical bath deposition technique has been used to deposit CdZnS thin films on soda-lime glass substrates. The structural, morphological, optoelectronic properties of as-grown films have been investigated as a function of different Zn²⁺ precursor concentrations. The X-ray diffractogram of CdS thin-film reveals a peak corresponding to (002) plane with wurtzite structure, and the peak shift has been observed with the increase of the Zn²⁺ concentration upon formation of CdZnS thin film. From morphological studies, it has been revealed that the diluted chemical bath deposition technique provides homogeneous distribution of film on the substrate even at a lower concentration of Zn²⁺. Optical characterization has shown that the transparency of the film is influenced by Zn²⁺ concentration and when the Zn²⁺ concentration is varied from 0 M to 0.0256 M, bandgap values of resulting films range from 2.42 eV to 3.90 eV while. Furthermore, electrical properties have shown that with increasing zinc concentration the resistivity of the film increases. Finally, numerical simulation validates and suggests that CdZnS buffer layer with composition of 0.0032 M Zn²⁺ concentration would be a promising candidate in CIGS solar cell.     

皮革中喹啉的测定

采用气相色谱-质谱法对皮革中喹啉含量进行了测定。通过对前处理条件(提取方式、提取溶剂、水浴温度、水浴时间)的优化,建立了皮革中喹啉的检测方法。实验结果表明,喹啉标准曲线线性范围为1.0~200.0 mg/kg,线性相关系数在0.999以上,检出限为1.0 mg/kg,空白样品及阳性样品中回收率均在85%~120%之间,相对标准偏差在2%~10%之间。所建立方法可用于皮革中喹啉含量的测试。     

催化剂WXP-100在棉针织物低温练漂中的应用

为解决纯棉针织物练漂温度高、能耗大等问题,研究自制低温练漂催化剂WXP-100对纯棉针织物练漂一浴前处理效果的影响。优化的低温练漂工艺条件为:催化剂WXP-100质量浓度为2 g/L,氢氧化钠质量浓度为2 g/L,多功能精练剂L质量浓度为6 g/L,30%双氧水体积分数为12 mL/L,70℃处理60 min。研究发现,催化剂WXP-100能够有效促进棉针织物练漂,70℃低温练漂织物的吸水性达到传统高温练漂效果,而且织物的顶破强力保留率高,纤维损伤明显减小,白度略低于传统练漂织物。     

Suppression of tool damage in ultraprecision diamond machining of stainless steel by applying electron-beam-excited plasma nitriding

Mirror surface machining of stainless steel with single-crystalline diamond tools is proposed in this study by applying a new nitriding method, called electron-beam-excited-plasma (EBEP) nitriding, to workpiece surfaces as pretreatment. It is well known that mirror surface finish of steel workpieces by conventional diamond cutting is unachievable owing to rapid tool wear. Nitriding of steel workpieces has been one of the several attempts to prevent the rapid tool wear of diamond tools. It has been reported that the rapid tool wear is caused by thermochemical interaction between diamond and steel, and that the wear can be greatly reduced by nitriding of steel. However, hard compounds formed on the outmost surfaces of workpieces by the conventional nitriding methods can cause micro-chippings of cutting tools. The authors has recently developed a new nitriding method called EBEP nitriding, in which a high dissociation rate for nitrogen molecules is achieved using the electron-beam-excited-plasma, and iron-compounds-free nitriding has been realized. Therefore, the EBEP nitriding is applied to a typical mold material, modified AISI 420 stainless steel, aiming at suppressing the micro-chippings as well as the thermochemical tool wear during diamond cutting of the stainless steel. The conventional ion nitriding and the gas nitrocarburizing are also applied to the same stainless steel in comparison. Chemical components of the nitrided workpiece surfaces are analyzed by an electron prove micro-analyzer (EPMA) and an X-ray diffraction (XRD) in advance, and turning experiments are conducted with single-crystalline diamond tools. Subsequently, changes in cutting forces and roughness of finished surfaces and tool damages after the turning experiments are evaluated. Finally, mirror surface machining by using the EBEP nitriding is demonstrated, and its advantages and disadvantages in the diamond cutting of stainless steel are summarized in comparison with the conventional nitriding methods.     

内燃机活塞环表面处理技术

活塞环在内燃机中有着支撑、密闭、储油、导热的作用,内燃机活塞环制备材料应该具备优良的加工性能、耐高温、耐腐蚀、导热性好且具有良好的强韧性,较好的与气缸材料表面的磨合性能。球墨铸铁和专用钢材已经成为制备内燃机活塞环的基础材料,目前国内外采用多种表面处理技术比如:镀铬、氮化、PVD与CVD镀膜、喷钼、喷涂陶瓷层等表面处理工艺进行表面改性,提高内燃机活塞环的使用寿命和使用性能。需要不断研究和开发新的内燃机活塞环的表面处理技术来满足实际生产和应用中内燃机越来越高的要求。     

基于状态观测器的电镀液温度状态反馈控制系统

针对电镀液温度控制系统,引入状态反馈控制。相对于传统的反馈控制,本方法可以获得更优异的性能。另外,考虑到镀液温度控制具有纯迟延的特点,提出了一种消去纯迟延的方法。仿真验证结果显示,控制效果良好。     

Corrosion resistance and electrical conductivity of plasma nitrided titanium

The continuous and dense Ti–N compound layers with a thickness ranging from 0.7 to 2.1 μm were formed on the titanium by plasma nitriding at 700 °C for different times with hollow cathode discharge assistance. Scanning electron microscope (SEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) were used to characterize the nitrided layer. XRD and XPS results showed that the compound layer was mainly composed of Ti₂N phase. The corrosion current density of 4 h nitrided titanium was 0.016 μA/cm² (cathode) and 0.03 μA/cm² (anode), respectively. The electrical conductivity of samples was evaluated by means of the interfacial contact resistance (ICR). The value of 4 h nitrided titanium was 4.94 mΩ-cm² which was much lower than that of original titanium 26.25 mΩ-cm² under applied force of 150 Ncm^?2 after corrosion test. The results showed that the electrical conductivity and corrosion resistance of the titanium bipolar plates (BPs) were apparently improved with the formation of Ti₂N compound layer.     

现代镀覆技术 第二部分──化学镀镍(续4)

给出了各种实用的化学镀镍配方及其工艺条件。     

High-performance vertically aligned Bi2O3 nanosheet arrays for water splitting applications by controlling the chemical bath deposition method parameters (precursor concentration and pH)

In this work, vertically aligned β-Bi₂O₃ nanosheet arrays are deposited on FTO using a simple, cost-effective, low-temperature, and easy-tunable technique called chemical bath deposition. Coatings were deposited through selective correlation of varying bismuth ion concentrations at fixed pH and, also, a fixed bismuth ion concentration at different pH values to optimize their structure, morphology, and optical properties. With an increase in bismuth precursor concentration from 0.008 M to 0.5 M, a more crystallized and compact coating with finer nanosheets was formed. Low pH values tended to result in either no coating or a coating composed of discrete particles. As the pH increased to the optimal level, a thicker and more compact coating with a morphology made of thicker and wider nanosheets was formed. Further increase in pH led to a non-uniform coating composed of small and large nanosheets that could not cover the entire surface of the substrate. The optimized photoelectrode exhibited a maximum photocurrent density of 470 μA/cm² at 1.23 V_RHE under 100 mW/cm² simulated sunlight, which is among the top recorded values of Bi₂O₃ photoelectrodes.     

盐浴软氮化42CrMo的摩擦学性能分析

对42CrMo进行盐浴软氮化处理,分析盐浴软氮化处理对42CrMo试样硬度的影响,研究不同润滑条件下42CrMo试样的摩擦学性能,分析其摩擦磨损机制。结果表明:盐浴软氮化处理过的42CrMo的平均硬度为HV747.33,约是未处理基体的(HV310)的2.5倍;在其他条件相同时,随载荷的增加,干摩擦条件下42CrMo的摩擦因数先增加后减小,边界润滑和油润滑条件下的摩擦因数不断增加;42CrMo在干摩擦条件下的摩擦因数、表面磨痕深度和磨损量均要明显高于边界润滑和油润滑条件下;在干摩擦条件下42CrMo的磨损机制为严重的黏着磨损和塑性变形,边界润滑条件下42CrMo表面磨损减缓,有轻微犁沟;油润滑条件下42CrMo表面为磨粒磨损,无明显变形。