采用QuEChERS结合UHPLC-MS/MS定量分析热加工肉制品中的三种胺类物质

本文采用QuEChERS技术结合超高效液相色谱-串联质谱（UHPLC-MS/MS）技术建立同时检测丙烯酰胺（AA）、亚硝胺（NAs）和杂环胺（HAAs）含量的方法，用于分析热加工肉制品中产生的胺类物质。结果表明:该方法检测出的三类成分20种胺类物质在相应浓度范围内显示出良好的线性关系（R2>0.991），检测限和定量限分别为0.01~1.6 ng/g和0.03~4.8 ng/g，日内回收率介于66.3%~116.5%之间，日内精密度介于0.78%~9.0%之间。每个胺类物的5×LOQ加标水平计算的日间精度范围为3.4%~9.4%。该方法应用于煎烤的四种肉制品中AA、NAs和HAAs的分析，共检测出9种胺类物质，浓度范围为0.03~31.26 ng/g。     

Life cycle assessment of HFC-134a production by calcium carbide acetylene route in China

HFC-134a is a widely used environment-friendly refrigerant. At present, China is the largest producer of HFC-134a in the world. The production of HFC-134a in China mainly adopts the calcium carbide acetylene route. However, the production route has high resource and energy consumption and large waste emission, and few of the studies addressed on the environmental performance of its production process. This study quantified the environmental performance of HFC-134a production by calcium carbide route via carrying out a life cycle assessment (LCA) using the CML 2001 method. And uncertainty analysis by Monte-Carlo simulation was also carried out. The results showed that electricity had the most impact on the environment, followed by steam, hydrogen fluoride and chlorine, and the impact of direct CO₂ emissions in calcium carbide production stage on the global warming effect also could not be ignored. Therefore, the clean energy (e.g., wind, solar, biomass, and natural gas) was used to replace coal-based electricity and coal-fired steam in this study, showing considerable environmental benefits. At the same time, the use of advanced production technologies could also improve environmental benefits, and the environmental impact of the global warming category could be reduced by 4.1% via using CO₂ capture and purification technology. The Chinese database of HFC-134a production established in this study provides convenience for the relevant study of scholars. For the production of HFC-134a, this study helps to better identify the specific environmental hotspots and proposes useful ways to improve the environmental benefits.     

Fabrication and upconversion luminescence properties of Er:SrF2 transparent ceramics compared with Er:CaF2

SrF₂ transparent ceramic is a promising upconversion material due to the low phonon energy. The effect of different sintering temperatures on Er:SrF₂ transparent ceramics was investigated. The suitable sintering temperature for Er:SrF₂ transparent ceramics was 900 °C by hot-pressed sintering in this study. High quality of Er:SrF₂ transparent ceramics with different doping concentrations were obtained. The upconversion luminescence spectra and decay behavior were compared between Er:SrF₂ and Er:CaF₂ transparent ceramics with different Er³⁺ doping concentration. The green emission of 5 at.% Er:SrF₂ ceramic was much stronger than that of 5 at.% Er:CaF₂ ceramic, while the red emission of Er:SrF₂ ceramic was almost the same as that of Er:CaF₂ ceramic. The upconversion luminescence lifetime of Er:SrF₂ transparent ceramics was longer than that of Er:CaF₂.All the results indicated Er:SrF₂ transparent ceramics was a candidate for green fluorescent upconversion materials.     

Chromium-promoted preparation of forsterite refractory materials from ferronickel slag by microwave sintering

The chromium-promoted preparation of forsterite refractory materials from ferronickel slag was investigated by microwave sintering of the slag with the additions of sintered magnesia and 0–10 wt% chromium oxide (Cr₂O₃). The thermodynamic calculations revealed that the addition of Cr₂O₃ can promote the formations of spinel and liquid phase and maintain high content of forsterite below 1500 °C. The experimental results showed that there existed a stronger promoting effect of Cr₂O₃ additive on the properties of refractory materials in the microwave field than that in conventional sintering. It was attributed to the preferential formation and growth of spinel with stronger microwave absorption than other phases (e.g., enstatite), the existence of more forsterite, and the enhanced densification in association with the presence of more liquid phase at the same temperature. By microwave sintering of the mixture of ferronickel slag, 25 wt% sintered magnesia, and 4 wt% Cr₂O₃ at 1350 °C for 20 min, a superior refractory material with refractoriness of 1801 °C, thermal shock resistance of 6 times, bulk density of 2.97 g/cm³, apparent porosity of 1.4%, and compressive strength of 197 MPa was obtained. Compared with that prepared by conventional sintering at 1350 °C for 2 h, the refractoriness and thermal shock resistance were increased by 175 °C and 100%, respectively. The present study provided a novel method for preparing high-quality refractory materials from ferronickel slag and relevant industrial wastes.     

利用FDM和随机共振检测风机主轴承微弱旋转信号

轴承作为风力发电机设备中重要部件,其健康状态直接影响风力发电机运行的稳定性和现场的安全可靠性.由于风力发电机特殊的工作环境,导致采集到的振动信号中包含大量的噪声干扰,难以准确提取轴承振动信号包含的信息成分,给评估主轴承健康状态带来困难.因此本文采用将傅立叶分解(Fourier decomposition method,FDM)和随机共振(Stochastic resonance,SR)相结合的方式提取信号中微弱的轴承振动信息.首先用FDM将原始信号自适应地分解为一系列包含轴承振动特征的傅立叶频带函数,然后找出相关性大的频带函数进行重构,最后采用SR对重构信号进行分析获得特征频率,判断轴承的健康状态.结果 显示,将两种方法相结合能有效提高输出信噪比,提升特征频率检测的精度,为实现风机轴承早期微弱故障诊断提供帮助.     

Molecular fingerprint and machine learning to accelerate design of high-performance homochiral metal–organic frameworks

Computational screening was employed to calculate the enantioseparation capabilities of 45 functionalized homochiral metal–organic frameworks (FHMOFs), and machine learning (ML) and molecular fingerprint (MF) techniques were used to find new FHMOFs with high performance. With increasing temperature, the enantioselectivities for (R,S)-1,3-dimethyl-1,2-propadiene are improved. The “glove effect” in the chiral pockets was proposed to explain the correlations between the steric effect of functional groups and performance of FHMOFs. Moreover, the neighborhood component analysis and RDKit/MACCS MFs show the highest predictive effect on enantioselectivities among the four ML classification algorithms with nine MFs that were tested. Based on the importance of MF, 85 new FHMOFs were designed, and a newly designed FHMOF, NO₂-NHOH-FHMOF, with high similarity to the optimal MFs achieved improved chiral separation performance, with enantioselectivities of 85%. The design principles and new chiral pockets obtained by ML and MFs could facilitate the development of new materials for chiral separation.     

Optical design of the Lyman alpha based beam emission spectroscopy(LAB)diagnostic on the HL-2A tokamak

In this article, we present the optical design of a novel diagnostic on the HL-2 A tokamak, i.e. the20-channel edge Lyman-alpha beam emission spectroscopy, which is a promising solution for edge density turbulence research on tokamaks, as it offers the possibility of density fluctuation measurement with a 3.3 mm spatial resolution while maintains a high temporal resolution of1 μs. The optical path, including the reflective collection optics, the high-dispersion spectrometer, and the linear detector array, is carefully optimized to obtain a good image quality and a high throughput. The maximum root mean square radius of the collection optics is 64 μm.The detected photon flux is estimated to be about 10~(11) photons/s/channel.     

基于多尺度的贝叶斯模型显著性检测

针对传统基于贝叶斯模型的显著性检测算法存在准确率不理想的问题,提出了一种基于多尺度的贝叶斯模型显著性检测算法。通过超像素分割算法(SLIC)将原图分割成不同尺度的超像素,根据超像素边界信息得到背景种子,进而通过距离计算和多尺度融合得到背景先验;对原图进行颜色增强,采用Harris算子对增强图进行检测角点求得凸包,融合不同尺度下的超像素得到凸包先验;融合背景先验和凸包先验得到最终先验;利用颜色直方图和凸包计算似然概率;将最终先验和似然概率通过贝叶斯模型计算显著图。在公开数据集MSRA1000、ECSSD上与多种传统算法进行准确率和召回率对比,该算法有更好的表现。