水力空化改质对重质原油沥青质及性质的影响

利用水力空化过程产生局部的高温、高压、高射流以及强大的剪切力等极端化学物理条件改质处理沙特重质原油，试验结果表明：沙特重质原油经过水力空化改质后粘度由13.61降低至7.22mm2/s，残碳由7.16%降低至6.48%，实沸点蒸馏后减压渣油降低1个百分点。进一步采用APPI FT-IR MS、XRD、FT-IR、SEM和粒度分布等技术研究了水力空化改质对沙重原油分子组成，沥青质团聚体微晶结构、沥青质胶束粒径分布、沥青质官能团、沥青质形貌等方面的影响，从分子角度阐述空化改质重油的机理。研究结果表明：水力空化改质后沙重原油分子量分布、芳烃类化合物缔合作用变小；沥青质对低DBE化合物吸附性能降低；沥青质团聚体微晶结构更加松散；沥青质胶束粒度分布降低；沥青质分子相互团聚作用力减弱。进一步考察了水力空化改质前后减压渣油延迟焦化性能，改质处理后焦炭产率降低1.85个百分点，液体收率和气体产率分别增加1.52和0.33个百分点，水力空化改质对沥青质性质、结构特点的改善能够有效的提高其加工性能。     

Degradation analysis of the core components of metal plate proton exchange membrane fuel cell stack under dynamic load cycles

The durability of metal plate proton exchange membrane fuel cell (PEMFC) stack is still an important factor that hinders its large-scale commercial application. In this paper, we have conducted a 1000 h durability test on a 1 kW metal plate PEMFC stack, and explored the degradation of the core components. After 1000 h of dynamic load cycles, the voltage decay percentage of the stack under the current densities of 1000 mA cm^?2 is 5.67%. By analyzing the scanning electron microscopy (SEM) images, the surfaces of the metal plates are contaminated locally by organic matter precipitated from the membrane electrode assembly (MEA). The SEM images of the catalyst coated membrane (CCM) cross section indicate that the MEA has undergone severe degradation, including the agglomeration of the catalyst layer, and the thinning and perforation of the PEM. These are the main factors that cause the rapid increase in hydrogen crossover flow rate and performance decay of the PEMFC stack.     

海上热采防砂封隔器研制与室内试验

海上稠油热采开发过程中,通常采用蒸汽吞吐的方式进行原油开采。为满足稠油热采长效密封要求,研制了HPHT-215型热采防砂封隔器。封隔器胶筒采用特制的氟硅基复合材料+玻璃纤维网结构,并开展了材料性能评价测试。通过有限元分析和室内胶筒组合测试,对胶筒材料和组合结构进行了评价优化。室内全尺寸整机测试表明:封隔器能够满足耐温350 ℃、耐压21 MPa密封性能要求,并开展了高低温多轮次密封性能评价测试。该型热采防砂封隔器的研制成功,为海上稠油蒸汽吞吐多轮次开发提供了保障,具有广泛的应用前景。     

“灰绿”协同措施对银川市合流制溢流污染的影响EI北大核心CSCD

针对合流制管网系统在雨天溢流污染严重,造成城市水体黑臭现象的问题,以银川市某高密度城区合流制管网系统为例,基于SWMM模型,在短历时设计降雨和长历时设计降雨两种条件下,模拟分析了合流制溢流(CSO)调蓄池、雨污管道混错接改造、绿化带海绵化改造等“灰绿”协同措施对CSO污染的影响。结果表明:CSO调蓄池、雨污管道混错接改造、绿化带海绵化改造及“灰绿”措施结合4种方案在短历时、长历时设计降雨条件下,随着降水量的增加,溢流水量及溢流污染物负荷均增加,溢流削减率均逐渐减小,其中“灰绿”措施结合方案对溢流污染的削减效果最为显著;重现期小于5 a时,溢流水量削减率与溢流污染物负荷削减率基本达到80%;降雨条件为中雨时,污染物负荷削减率基本达到75%;重现期为20 a时,溢流水量削减率及TSS、COD、TP、NH^(+)_(4)-N负荷削减率分别达到64%、70%、70%、70%、70%;降雨条件为大雨时,溢流水量削减率及TSS、COD、TP、NH^(+)_(4)-N负荷削减率分别达到28%、32%、26%、31%、33%。     

基于跨临界CO2热泵的茶叶生产能源系统负荷削减潜力

乡村产业中的化石能源设备逐渐被电能技术替代，引起了乡村负荷波动增大、部分时段产生集中高负荷的问题。为了解决以上问题，将低品位清洁能源应用至乡村的茶叶生产中，针对烘茶全过程的工艺要求提出了跨临界CO₂热泵烘茶技术；并以某茶叶生产乡村为对象，对其代表台区的全年日用电量及产茶日负荷进行了分析，得出采用CO₂热泵烘茶后其负荷得到大幅度削减，整体可降低至原负荷的39.6%~46.8%，峰值负荷与平时负荷的比值由原本的13.6降至5.4~6.2。跨临界CO₂热泵应用至农产品生产中可有效缓解乡村供电压力。     

Thermomechanical stability and inelastic energy dissipation as durability criteria for fuel cell gas diffusion media with pre-assembly effects

In this article, pre-assembly hot-press pressure and thermal expansion effects in gas-diffusion layers (GDLs) are addressed to explore the practicalities of the constitutive model reported in the companion article. A facile technique is proposed to include deformation history dependent residual strain effects. The model is implemented in the numerical environment and compared with widely followed conventional models such as isotropic and orthotropic material models. With the normal and accelerated thermal expansion effects no significant variation in stresses or strains is reported with the compressible GDL model in contrast to the conventional incompressible form of the GDL model. The present work identifies the critical differences with advanced and extended variants of the model along with conventional GDL material models in terms of planar stress/strain distribution and the membrane response. Finally, the model is simulated for micro-cyclic stress loads of varying amplitudes that imitate the real working conditions of fuel cell. The inelastic energy dissipation in GDLs is predicted using the proposed model, which is utilized further to distinguish the safe (elastic) and unsafe (inelastic shakedown) operating limits. The inelastic collapse of GDLs is shown to be a active function of high amplitude micro-cyclic load with high initial clamping load.     

Effect of heat treatment and zircon addition on the properties of low-cement castables based on recycled alumina grog

In this investigation, low-cement castables were prepared using 70% alumina grog aggregates obtained from crushed alumina brick waste. The aggregates were thermally treated at 1550 °C for 3 h. Four types of low-cement castables were prepared with various types of aggregates (alumina grog with or without thermal treatment) and fillers (with or without zircon addition), and they were evaluated in terms of their physical, thermal, and chemical properties. Microstructural analysis via scanning electron microscopy (SEM) was performed on the castables before and after slag attack. Compared to the other fabricated castables, the thermally treated alumina grog castables with zircon showed better physical properties, such as a higher bulk density, cold crushing strength, and modulus of rupture and a lower apparent porosity and water absorption. In addition, they had a higher positive linear thermal expansion, refractoriness under load, permanent linear change, and hot modulus of rupture. The results of the SEM with energy dispersive X-ray analysis of the prepared castables confirmed that the mullite and anorthite phases were predominant when zircon was not added and the zircon–mullite phase additionally appeared upon the incorporation of zircon. A quantitative elemental analysis via X-ray fluorescence spectroscopy was employed to determine the composition of the castables. X-ray diffraction analysis showed that the alumina grog castables had a high mullite and low anorthite content, and the thermally treated alumina grog had a high anorthite, low mullite, and high zircon content. The improvement in the mechanical and thermo-mechanical properties of the castables with thermally treated alumina grog and added zircon can be attributed to the formation of the zircon–mullite phase with a low mullite phase content.     

Generation,validation and application of dynamic load profiles in flow measurement using cavitating Herschel–Venturi nozzles

Today, utility meters for water are tested for measurement behavior at stable operating conditions at specified flow rates as part of the approval process. The measurement error that occurs during start and stop or when changing between flow rates may not be taken into account. In addition, there are new technologies whose measuring behavior under real-world conditions is only known to a limited extend. To take these facts into account, a new method has been developed and tested to determine the measurement behavior of water meters under dynamic load profiles as they occur in the real application. For this purpose, a test rig for flow rate measurement was extended by a cavitation nozzle apparatus and the generation of dynamic load profiles was validated. For the cavitation nozzles used, possible factors influencing the flow rate, such as temperature and purity of the water as well as the upstream pressure were investigated. Using different types of domestic water meters, the applicability of the dynamic test procedure was demonstrated and the measurement behavior of the meters was characterised.     

Simulations of NBI fast ion loss in the presence of toroidal field ripple on EAST

NBI fast ion losses in the presence of the toroidal field ripple on EAST have been investigated by using the orbit code GYCAVA and the NBI code TGCO. The ripple effect was included in the upgraded version of the GYCAVA code. It is found that loss regions of NBI fast ions are mainly on the low field side near the edge in the presence of ripple. For co-current NBIs, the synergy effect of ripple and Coulomb collision on fast ion losses is dominant, and fast trapped ions located on the low field side are easily lost. The ripple well loss and the ripple stochastic loss of fast ions have been identified from the heat loads of co-current NBI fast ions. The ripple stochastic loss and the collisioninduced loss are much larger than the ripple well loss. Heat loads of lost fast ions are mainly localized on the right side of the radio frequency wave antennas from the inside view toward the first wall. For counter-current NBIs, the first orbit loss due to the magnetic drift is the dominant loss channel. In addition, fast ion loss fraction with ripple and collision for each NBI linearly increases with the effective charge number, which is related to the pitch angle scattering effect.