Customization of ZrO2 loose/tight bilayer ultrafiltration membranes by reverse micelles-mediated aqueous sol-gel process for wastewater treatment

Two types of spherical zirconyl oxalate aqueous sols were successfully customized by a reverse micelles-mediated aqueous sol-gel process, and the sols were sequentially spin-coated on porous supports to prepare ZrO₂ loose/tight bilayer ultrafiltration membranes. After three times of spin-coating process, a defect-free ZrO₂ loose ultrafiltration membrane with pure water permeability of 110.5 ± 2.25 L m^?2 h^-1 bar^-1, molecular weight cut-off (MWCO) of 16.5 kDa and excellent rejection of up to 97.5 % for bovine serum albumin was fabricated. Then, the loose ultrafiltration membrane was used as a substrate to prepare ZrO₂ tight ultrafiltration membrane. Performances of tight ultrafiltration membrane regarding to permeability, retention of polyethylene glycol and treatment of dyes wastewater were evaluated. The tight ultrafiltration membrane with a thickness of 200 nm exhibited a pure water permeability of 22.5 ± 0.3 L m^-2 h^-1 bar^-1 and MWCO of 1150 Da. Additionally, the rejections of methyl red and methyl orange by the tight ultrafiltration membrane were both <65 %, while of alizarin red, direct red, bromocresol green and methyl blue achieved maximum values of 98.5 %, 99.2 %, 99.5 % and 99.6 %, respectively. The fouled membranes could restore the virgin performance for reuse by cleaning and low-temperature calcination.     

Localized corrosion of (lean) duplex stainless steels in immersion units of urban wastewater treatment plants

With lower alloying cost and higher mechanical properties, lean duplex stainless steels can be an alternative to the more commonly used austenitic stainless steels. However, these alloys are still not the preferred choice, probably due to a lack of field experience. A study was thus initiated in view of defining the limits of use of selected (lean) duplexes for urban wastewater treatment units. The present paper shows the localized corrosion performance of selected lean duplexes in chloride contaminated solutions. The results are compared with austenitic S30403 and S31603 and with the more standard duplexes S82441 and S32205. The effect of welding was also investigated. Exposures in field municipal wastewater plants were conducted for 1 year in low and high chloride content units. The results show that lean duplexes S32101 and S32202 can be used as alternatives to S30403 and S31603 in low chloride electrolytes. At 500 ppm of chloride content, duplex stainless steel S32304 showed better corrosion resistance than S30403 and S31603. For higher chloride contents (1000 ppm and above) the standard duplexes S82441 and S32205 shall be preferred.     

The P-graph approach for systematic synthesis of wastewater treatment networks

Wastewater treatment consists of three or four sequential stages: preliminary, primary, secondary, and tertiary. Each stage can comprise multiple alternative technologies that can perform the same tasks with different efficiencies, operating times, and costs. Thus, we propose a systematic approach for designing wastewater treatment networks by utilizing principles of mathematical modeling and generating an exhaustive enumeration of all the possible technologies and their connections during the early stages of designing a treatment facility. Some of these structures are nonintuitive and include recycling, reprocessing, bypasses, and multiple technologies in parallel or series to remove the same contaminant. The nonintuitive structures with multiple technologies may provide a measure of resilience compared to typical heuristic designs. Thus, the combination of P-graph methodology and the sequence of treatment technologies predicted via the optimization algorithm from the maximal structure is based on holistic considerations and does not lead to suboptimal solutions.     

Statistical optimization of operating parameters of microbial electrolysis cell treating dairy industry wastewater using quadratic model to enhance energy generation

The performance of Microbial electrolysis cell (MEC) is affected by several operating conditions. Therefore, in the present study, an optimization study was done to determine the working efficiency of MEC in terms of COD (chemical oxygen demand) removal, hydrogen and current generation. Optimization was carried out using a quadratic mathematical model of response surface methodology (RSM). Thirteen sets of experimental runs were performed to optimize the applied voltage and hydraulic retention time (HRT) of single chambered batch fed MEC operated with dairy industry wastewater. The operating conditions (i.e) an applied voltage of 0.8 V and HRT of 2 days that showed a maximum COD removal response was chosen for further studies. The MEC operated at optimized condition (HRT- 2 days and applied voltage- 0.8 V) showed a COD removal efficiency of 95 ± 2%, hydrogen generation of 32 ± 5 mL/L/d, Power density of 152 mW/cm² and current generation of 19 mA. The results of the study implied that RSM, with its high degree of accuracy can be a reliable tool for optimizing the process of wastewater treatment. Also, dairy industry wastewater can be considered to be a potential source to generate hydrogen and energy through MEC at short HRT.     

Improvement of gaseous bioenergy production from spent coffee grounds Co-digestion with pulp wastewater by physical/chemical pretreatments

Two steps of hydrolysis and anaerobic biogas production processes was investigated in this study. In the first step, subcritical water (SBW) hydrolysis and chemical (acid/alkali) pretreatments were carried out to enhance hydrolysis efficiency by obtaining and analyzing the total volatile fatty acids (TVFA), chemical oxygen demand (COD), and total sugar productions from spent coffee grounds (SCG) hydrolysate. The subcritical water (SBW) hydrolysis under the condition of temperature 150 °C for 30 min can greatly improve the organic matter breakdown and reached the COD concentration of 1010 g/L which was 30% higher than the untreated raw SCG. For chemical pretreatments, it was found that the alkaline hydrolysis of SCG resulted in the greatest total sugar concentration of 181 g/L whereas the operation conditions were 2.0 M NaOH at 60 °C for 1 h. The peak of TVFA concentration 3725 mg/L was found at the acid hydrolysis of SCG with 1.0 M H₂SO₄ acid, 60 °C for 1 h. The optimal biomethane yield of 115 mL/g COD was obtained when 1.0 M H₂SO₄ acid hydrolysate co-digestion with pulp wastewater which increase methane yield production 8 times of raw pulp wastewater. The pretreatment process was confirmed in this study can significant improve the converting of the biowastes to bioenergy efficiency.     

Magnetic recyclable ZnO/SrFe12O19 photocatalyst for effective photodegradation of rhodamine B under simulated sunlight

This work develops a novel magnetic photocatalysts ZnO/SrFe₁₂O₁₉ (ZS) synthesized with hydrothermal process. The introduction of SrFe₁₂O₁₉ not only enhances the photocatalytic behavior of ZnO towards Rhodamine B (RhB) decomposition, but also reinforces the recycling stability. Especially, ZS-5 composite exhibits the optimal photocatalytic performance, and the RhB decomposition reaches 99.5% after being exposed to simulative sunlight for 70 min, which is obviously superior to that of bare ZnO. Furthermore, the ZS-5 can be recovered from RhB solution by an extra magnet space and reused. After five recycles, the RhB removal efficiency can still be maintained over 90%. Such prominent photocatalytic property and stability of ZS-5 are associated with the greatly improved detachment efficiency of photoexcited carriers in a magnetic field. This study could provide a new-type recyclable photocatalyst that can effectively purify dye wastewater for convenient recovery.     

Nanotechnology‐based wastewater treatment

Water contamination is a global challenge impacting both the environment and human health with significant economic and social costs. The growing scarcity of usable water resources requires effective treatment of wastewater. In this context, developing cheaper, safer and more efficient wastewater treatment technologies are the need of the hour. One promising approach that several studies have reported success has been the usage of nanomaterials in water and waste water management. The rapid progress of research in nanomaterial sciences has shown their growing potential; however, there has not been a great amount of information available on their implementation. This review focuses on developments in nanotechnology that hold strong potential for wastewater treatment. The review covers key techniques in nanomaterial‐based water treatments including adsorption, filtration and photocatalysis with recent examples showing how to improve their properties and efficiencies according to the need.     

Enhancement effect of zero-valent iron nanoparticle and iron oxide nanoparticles on dark fermentative hydrogen production from molasses-based distillery wastewater

This study investigates the effect of two different iron compounds (zero-valent iron nanoparticle: nZVI and iron oxide nanoparticles: nIO) and pH on fermentative biohydrogen production from molasses-based distillery wastewater. The nZVI and nIO of optimum particle sizes of 50 nm and 55 nm respectively were synthesized and applied for fermentative hydrogen (H₂) production. The addition of nIO & nZVI at (0.7 g/L, pH: 6) resulted in the highest H₂ yield, H₂ production rate, H₂ content and COD reduction. Moreover, the kinetic parameters of H₂ production potential (P) and H₂ production rate (R_m) increased to 387 mL, and 22.2 mL/h, respectively for nZVI, these values were 363 mL and 21.8 mL/h for nIO. The results obtained indicated the positive effect of nZVI and nIO addition on enhanced fermentative H₂ production. The addition of nZVI & nIO resulted in 71% and 69.4% enhancement in biohydrogen production respectively.