一种可传输轨道角动量的螺旋光子晶体光纤北大核心

设计了一种基于阿基米德螺线的新型螺旋光子晶体光纤,该光纤以二氧化硅为基底材料,包层由24个螺旋臂组成,每个螺旋臂包含11个小空气孔,纤芯设有大空气孔,包层与纤芯中间的环形区域用于传输轨道角动量模式。该结构在1300~1800 nm波段上可支持22种轨道角动量模式稳定传输,在1550 nm波长下,有效折射率差最高可达2.89×10^(-3),色散系数最低可达66.4 ps/(nm·km),非线性系数最低可达2.17 W^(-1)·km^(-1),且1500~1600 nm波段上的色散值变化均小于15.15 ps/(nm·km)。此螺旋光子晶体光纤不仅结构简单,且具有低非线性、色散平坦的性能,为螺旋光子晶体光纤的设计提供了思路。     

一种用于电气设备状态监测的新式FBG传感器北大核心CSCD

为了监测绕组变压器的静态应力场和发生短路等故障时的动态应力变化,设计了一种用于电气设备状态监测的新式FBG传感器。该传感器由聚醚醚酮材料封装的FBG构成,通过内部圆锥形空腔结构实现将轴向应力集中于FBG敏感位置。通过仿真对不同压力强度下传感器结构的应力场部分及形变趋势进行了计算与分析,论证了设计的合理性。实验分别对静态载荷和动态冲击进行测试,结果显示,在静态压载测试中,当100 N相似文献   

超高分子量聚乙烯纤维增强中空蜂窝模压复合材料性能研究

为研制车船等壳体所用的轻质、高强复合板材,选用超高分子量聚乙烯(UHMWPE)短纤维纱,制备成单层经纬为120根/(10 cm)的平纹组织,采用多组经纱持续更替交织层的方法制成2L(1+0)型、4L(2+1)型、6L(3+2)型3种多层角联锁结构织物,采用扦插芯棒、模压成型方法制成菱形蜂窝状的热固性环氧树脂基中空板,并与2块真空吸液法制成的面板组成“三合一”复合板,同时测定了复合板材的结构特征及其平拉、平压和弯曲性能。结果表明:3种类型复合板的密度均远小于水的密度,其中6L(3+2)型最小,为0.48 g/cm³;复合板层数越多,环氧树脂越难渗透尤其是在中空板菱形交叉点处,复合板平拉、平压、抗弯曲强度则呈现递增,制成的6L(3+2)型复合板试样平压强度可达到1.03 MPa。     

Stability assessment of 3D reinforced soil structures under steady unsaturated infiltration

Internal stability assessment of geosynthetic-reinforced soil structures (GRSSs) has been commonly carried out assuming plane-strain conditions and dry backfills. However, failures of GRSSs usually show three-dimensional (3D) features and occur under unsaturated conditions. A procedure based on the kinematic limit-analysis method is proposed herein to assess 3D effects and the role of steady unsaturated infiltration on the required geosynthetic strength for GRSSs. A suction stress-based framework is used to describe the soil stress behavior under steady unsaturated infiltration. Based on the principle of energy-work balance, the required geosynthetic strength is determined. A comparison analysis with the prior research is conducted to verify the developed method. Two kinds of backfills, i.e., high-quality backfill and marginal backfill, are considered for comparison in this work. It is shown that accounting for 3D effects and the role of unsaturated infiltration considerably reduces the required geosynthetic strength. The 3D effects are primarily affected by the width-to-height ratio of GRSSs, and the contribution of unsaturated infiltration is mainly influenced by the soil type, flow rate, GRSS's height, and location of the water table.     

Experimental study on the load bearing behavior of geosynthetic reinforced soil bridge abutments with different facing conditions

This paper presents an experimental study on reduced-scale model tests of geosynthetic reinforced soil (GRS) bridge abutments with modular block facing, full-height panel facing, and geosynthetic wrapped facing to investigate the influence of facing conditions on the load bearing behavior. The GRS abutment models were constructed using sand backfill and geogrid reinforcement. Test results indicate that footing settlements and facing displacements under the same applied vertical stress generally increase from full-height panel facing abutment, to modular block facing abutment, to geosynthetic wrapped facing abutment. Measured incremental vertical and lateral soil stresses for the two GRS abutments with flexible facing are generally similar, while the GRS abutment with rigid facing has larger stresses. For the GRS abutments with flexible facing, maximum reinforcement tensile strain in each layer typically occurs under the footing for the upper reinforcement layers and near the facing connections for the lower layers. For the full-height panel facing abutment, maximum reinforcement tensile strains generally occur near the facing connections.     

Development of mullite fibers and novel zirconia-toughened mullite fibers for high temperature applications

Polycrystalline mullite fibers and novel zirconia-toughened mullite (ZTM) fibers with average diameters between 9.7 and 10.3 μm containing 3, 7 and 15 wt.-% tetragonal ZrO₂ (ZTM3, ZTM7, ZTM15) in the final ceramic were prepared via dry spinning followed by continuous calcination and sintering in air. A shift in the formation of transient alumina phases and tetragonal ZrO₂ to higher temperatures with increasing amounts of ZrO₂ was observed. Concomitantly, the mullite formation temperature was lowered to 1229 °C for ZTM15 fibers. X-ray diffraction revealed formation of the desired tetragonal crystal structure of ZrO₂ directly from the amorphous precursor. Room temperature Weibull strengths of 1320, 1390 and 1740 MPa and Weibull moduli of 9.5, 7.1 and 9.0 were determined for mullite, ZTM3 and ZTM15 fibers, respectively. Average Young’s moduli ranged from 190 to 220 GPa. SEM images revealed crack-free fiber surfaces and compact microstructures independent of the amount of ZrO₂.     

Design and fabrication of lutetium aluminum silicate glass and nanostructured glass for radiation detection

Flexible scintillating fiber plays an important role in X-ray radiation monitoring and high-resolution medical imaging, while construction of scintillating fiber derived from the commercial material system meet with limited success. Here, we report the design and successful fabrication of the Ce-activated lutetium aluminum silicate glass, nanostructured glass, and fiber, and explore their scintillating properties. The scintillating glass with optimized composition and optical properties is determined. The crystallization behavior of lutetium aluminum silicate glass is studied and the nanostructured glass embedded with orthorhombic Lu₂Si₂O₇ phase is successfully constructed for the first time. Importantly, the crystalline layer thickness of the nanostructured glass can be finely tuned and ~172.89% enhancement in the scintillating performance can be achieved. Furthermore, the fiber with large sized core is fabricated and its radiation response properties are tested. The results show that it exhibits high sensitivity and its scintillating emission is lineally dependent on the X-ray power, indicating the potential application for radiation detection.     

Multiple material domain‐based computational tools for ease assessment of modal parameter in photonic crystal fibers

We report here the development of two computational tools PCFPS (Photonic Crystal Fiber Parameter Study) and PCFPA (Photonic Crystal Fiber Parameter Analysis), equipped with graphical user interface (GUI) for modeling of photonic crystal fiber. The tools are based on different structural parameters, and they provide characteristic analysis of the modal parameters from the structural parameters. The main feature of PCFPS is that it enables the user to find out the values of each defining modal parameter that has an immense contribution towards the manufacture of photonic crystal fiber. Additionally, PCFPA allows the user to observe the variation in the modal parameters with respect to the changes in structural parameters (such as d, Λ, d/Λ, and λ/>Λ). Besides their ease of use, these two schemes have high computational precision and adaptability, giving a novel platform to optical engineers to modulate the microstructured fibers according to their requirement.     

Preparation and antifouling performance of thin inorganic ultrafiltration membrane via assisted sol-gel method with different composition of dual additives

A novel TiO₂ thin film was prepared on the ceramic hollow fiber by the sol-gel method using poly(vinylpyrrolidone) (PVP) and polyvinyl alcohol (PVA) as additives. SEM images verified the formation of TiO₂ layer with various thickness using different composition of titania sols. The effect of the PVP and PVA contents on the TiO₂ sol properties, the separation and the antifouling performance of the ultrafiltration membranes were investigated thoroughly. When the contents of PVP and PVA were 1.0 wt% and 0.8 wt%, respectively, the resultant membrane showed a thickness of 0.55 μm with a pure water flux of 255 L m^?2 h^?1. In addition, the adherent foulant bovine serum albumin was applied to evaluate the antifouling performance. During the three fouling-recovery cycles, the flux recovery ratio and the flux decay ratio maintained about 99% and 30%. The BSA flux and rejection were still 169 L m^?2 h^?1 and 96.9% after the cycles, indicating a superior antifouling property.     

High-Performance All-Solid-State Supercapacitor Electrode Materials Using Freestanding Electrospun Carbon Nanofiber Mats of Polyacrylonitrile and Novolac Blends

Herein, this paper reports a facile method to prepare electrospun carbon nanofiber mats (ECNFMs) with high specific surface area and interconnected structure using polyacrylonitrile (PAN) as a precursor and novolac resin (NOC) as a polymer sacrificial pore-making agent. Without additional treatment, the prepared ECNFMs have a highly porous structure because NOC decomposes in a wider temperature range than most polymer activators. The NOC content in the PAN nanofibers shows important effects on porosity. The BET specific surface area of ECNFMs reaches a maximum of 1468 m² g⁻¹ when the precursor nanofibers contained 30 wt% NOC (ECNFM-3) after carbonization at 1000 °C. The supercapacitor device from ECNFM-3 electrode and all-solid-state electrolyte shows excellent cycling durability and high specific capacitance: ≈99.72% capacitance retention after 10 000 charge/discharge cycles and ≈320 mF cm⁻² at 0.25 mA cm⁻². Furthermore, it shows a large energy density of ≈11.1 $\mu$Wh cm⁻² under the power density of 500 mW m⁻². Activation of carbon nanofibers simply by the addition of NOC into precursor nanofibers can offer a handy way to prepare ECNFMs for high-performance all-solid-state supercapacitors and other potential applications.