控制爆破法处理卡钻事故

介绍了在包头市某工程实施管道穿越黄河施工中,采用爆破法处理卡钻的经验。针对深水环境条件及钻杆内径小不宜采用集团装药的条件,确定采用"小直径爆破筒,钻杆内部装药"的爆破方案,阐述了爆破设计及施工注意事项。可供类似工程参考。     

Dynamic simulation of hydrogen-based off-grid zero energy buildings with hydrogen storage considering Fanger model thermal comfort

In this study, some locations with different climates, off-grid zero energy buildings with hydrogen energy storage systems are designed, and transient analysis is conducted. These considered buildings supply their electricity consumption without using the electrical grid and PV panels or wind turbines. Also, they supply thermal comfort to occupants by using a vapor compression chiller and humidifier. Domestic hot water of occupants is supplied using solar collectors. For analyzing building's performance and objectives achievement, TRNSYS software is used. Also, for evaluating occupant thermal comfort, the Fanger model is used. The considered building is a one-story building with a 150 m² area. Four occupants are considered. Both of them are seated at rest, and another is seated with light working such as typing. Using the Fanger model equation and MATLAB software, the thermal comfort of occupants is determined. For domestic hot water consumption, verified profiles that vary during 24 h of the day are considered. Achieved results show that for humid and cold cities, PV panels with an area of 73 and 76 m² can be supplied the required electricity of considered building with four occupants and battery state of charge is higher than 50% and 10%, respectively. Moreover, with a suitable air conditioner system, the predicted percentage of dissatisfied (PPD) can be lower than 12% and 8% for humid and cold cities. Therefore, the building can be converted to a zero-energy building using its rooftop area.     

Effects of different metal corrosion inhibitors on hydrogen suppression and film formation with Mg–Zn alloy dust in NaCl solutions

To improve the safety of wet dust removal systems for processing magnesium-based alloys, a new method is proposed for preventing hydrogen generation. In this paper, hydrogen generation by Mg–Zn alloy dust was inhibited with six common metal corrosion inhibitors. The results showed that sodium dodecylbenzene sulfonate was the best hydrogen inhibitor, while CeCl₃ enhanced hydrogen precipitation. The film-forming stability of sodium dodecylbenzene sulfonate was tested with different contents, temperatures, Cl^? concentrations and perturbation rates. The results showed that this inhibitor formed stable protective films on the surfaces of Mg–Zn alloy particles, and adsorption followed the Langmuir adsorption model.     

Status and initial experiments of DRAGON-V facility for lithium-lead blanket technologies of hydrogen fusion reactors

A dual-coolant integrated experimental facility named DRAGON-V has been developed at the Institute of Nuclear Energy Safety Technology, Hefei Institute of Physical Science, Chinese Academy of Sciences, for the key technology research and performance evaluation of candidate liquid lithium-lead (PbLi) blanket of hydrogen fusion reactors. The loop is composed of a material test sub-loop and thermal-hydraulic test sub-loop, the design parameters are PbLi inventory 20 tons, PbLi temperature up to 550 °C, the maximum PbLi flow rate up to 40 kg/s. A novel cold trap system is designed to remove the suspended and crystalized impurities in PbLi fluid with three cooling zones and cross row arrangement of rod bundle filter elements. The paper describes the loop itself and its major components, initial loop testing, flow and measurement diagnostics and current experiments. The obtained test results of the loop and its components have demonstrated that the new facility is fully functioning and ready for experimental studies of material corrosion with/without a magnetic field, magnetohydrodynamic (MHD) effect, purification, heat and mass transfer phenomena in PbLi flows and can also be used in mock-up testing in conditions relevant to fusion applications.     

Combining a new baseboard radiator with a fan coil system for improving heating performance and reduce energy consumption

In the present work, the heating performance of a new system combined with a new modified baseboard radiator and fan coil is investigated. Using longitudinal fins with special geometry and also forced airflow at the end of the system causes that at the lower inlet water temperature compared with the conventional models, higher heat output rate be obtained. The heat output rate of the new modified system is obtained by experimental metrology based on the European Standard No. EN-442. Temperature and velocity distribution in the room space is done by simulation of the modified system in the Flovent software. Computational fluid dynamics (CFD) results are validated against experimental results and there is a good agreement between them. Also, the energy consumption of the system during the winter season is calculated in TRANSYS software. Experimental results show that the heat output rate of a new modified heating system with inlet water temperature in the range of 45–55°C is on average 4.17 times higher compared with the conventional model. CFD simulation also showed that the combined system provides good thermal comfort conditions. Energy consumption of the new system reduced about 13% compared with conventional models.     

Co?N graphene encapsulated cobalt catalyst for H2O2 decomposition under acidic conditions

Hydrogen peroxide (H₂O₂) has been listed as one of the 100 most important chemicals in the world. However, huge amount of residual H₂O₂ is hard to timely decomposed into O₂ and H₂O under acidic condition, easily resulting in explosion hazard. Here, we reported a core–shell structure catalyst, that is graphene with Co N structure encapsulated Co nanoparticles. Co N graphene shell serves as the active site for the H₂O₂ decomposition, and Co core further enhance this decomposition. Benefiting from it, the H₂O₂ decomposition were close to 100% after 6 cycles without pH adjustment, which increased 6 orders of magnitude compared with no catalyst. At the same time, the O₂ generation reached 99.67% in 2 h with little metal leaching, and ·OH has been greatly inhibited to only 0.08%. This work can cleanly remove H₂O₂ with little deep oxidation and protect the process of H₂O₂ utilization to achieve a safer world.     

Double pyrovanadates CaMgV2O7: Formation mechanism,phase structure,and thermodynamic properties

A double pyrovanadate CaMgV₂O₇ sample was synthesized via a facile solid-state route under an air atmosphere. The nonequilibrium formation pathways of the CaMgV₂O₇ were investigated via powder X-ray diffraction. A multistep reactions path (metavanadates–pyrovanadates–double pyrovanadate CaMgV₂O₇) was proposed to describe the formation of the CaMgV₂O₇ considering the thermodynamic and kinetic factors. The cell unit parameters of the CaMgV₂O₇ sample indicated the crystallization according to a monoclinic system with space group P12/c1(14), and the lattice parameters of a = 6.756 Å, b = 14.495 Å, c = 11.253 Å, β = 99.12, and V = 108.806 Å³. X-ray photoelectron spectroscopy also confirmed the +5 oxidation state vanadium in CaMgV₂O₇. The endothermic effects at 1033 and 1143 K were related to the incongruent melting and liquidus temperatures of CaMgV₂O₇, respectively. The comprehensive thermodynamic properties of CaMgV₂O₇ were established in both low- and high-temperature regions, utilizing a physical property measurement system and multi-high-temperature calorimetry (96 lines). The heat capacity (200 J mol K⁻¹) and entropy (198 J mol K⁻¹) at 298.15 K were computed based on the low-temperature heat capacity values, and the enthalpy of formation at 298.15 K was also estimated. The fitted high-temperature capacity can be used to obtain the changes in the enthalpy, entropy, and Gibbs free energy. This study is part of building a reliable thermodynamic database of the CaO–MgO–V₂O₅ system.     

A triptycene derived hypercrosslinked polymer for gas capture and separation applications

This work describes facile synthesis of a porous polymeric material ( T-HCP ) using readily available reagents. Specifically, T-HCP is a thermally stable and hypercrosslinked polymer (HCP) that is essentially microporous with a high BET specific surface area (940 m² g^?1). Triptycene based polymers are known to feature internal free volume. Thus, the incorporation of triptycene units and extensive crosslinking by an external cross-linker in T-HCP makes it a promising adsorbent for small gas capture applications. Experimental results show that T-HCP demonstrated good CO₂ capture capacity of 132 mg g^?1 (273 K, 1 bar). Molecular hydrogen storage capacity of T-HCP is estimated to be 17.7 mg g^?1 (77 K, 1 bar). T-HCP revealed high CO₂/N₂ selectivity (up to 63) as well as promising CO₂/CH₄ (up to 9.1) selectivity suggesting its potential applicability for CO₂ separation from flue and natural gases.     

“半翻转”教学模式下评价指标体系研究与实践

研究基于“半翻转”教学模式的线上教学评价指标体系,包括课前活动开展、课中教学活动设计、课后任务以及基于此过程中的评价指标体系设计。最后通过层次分析法设计评价指标权重,设计评价算法得到动态评价结果。该评价指标体系应用在本专业“数据结构与算法”课程中,并得到良好的应用效果。     

Flash Lamps as Ignition and Initiation Sources of the VS-2 Pyrotechnic Composition

In the present work it is found that the pyrotechnic composition VS-2 can be initiated with flash lamps IFC-500 and EVIS. VS-2 pyrotechnic composition contains 90% of mercury（Ⅱ） 5-hydrazinotetrazolate perchlorate and 10% of optically transparent copolymer of 2-methyl-5-vinyltetrazole and methacrylic acid （PVMT）. We have found that the flash lamps make it possible to initiate combustion of VS-2 composition with its transition to detonation both in cylindrical charges placed in brass caps of 5 mm diameter and 2 mm high， and film charges with 10 mm×80 mm in size and surface weights of 60 mg·cm^-2 and 90 mg·cm^-2， showing ignition delay times 10 μs and 3 μs， respectively. We also measured detonation velocities for VS-2 composition film charges， which were 4375-4505 m·s^-1 （of the charge being surface mass 60 mg·cm^-2） and 4221-4281 m·s^-1 （of the charge being surface mass 90 mg·cm^-2） and their blasting action on the aluminum plate. The depths of the normal shock wave imprints at the charge-barrier interface were 0.6-0.7 mm （for surface mass of the film charges 60 mg·cm^-2） and 1.2-1.3 mm （for surface mass of the film charges 90 mg·cm^-2）.