Research on phase shift characteristics of electromagnetic wave in plasma

The phase shift characteristics reflect the state change of electromagnetic wave in plasma sheath and can be used to reveal deeply the action mechanism between electromagnetic wave and plasma sheath. In this paper, the phase shift characteristics of electromagnetic wave propagation in plasma were investigated. Firstly, the impact factors of phase shift including electron density,collision frequency and incident frequency were discussed. Then, the plasma with different electron density distribution profiles were employed to investigate the influence on the phase shift characteristics. In a real case, the plasma sheath around the hypersonic vehicle will affect and even break down the communication. Based on the hypersonic vehicle model, we studied the electromagnetic wave phase shift under different flight altitude, speed, and attack angle. The results indicate that the phase shift is inversely proportional to the flight altitude and positively proportional to the flight speed and attack angle. Our work provides a theoretical guidance for the further research of phase shift characteristics and parameters inversion in plasma.     

Influence of the SiC matrix introduction time on the microstructure and mechanical properties of Cf/Hf0.5Zr0.5C-SiC ultra-high temperature composites

C_f/Hf_0.5Zr_0.5C-SiC composites were prepared by introducing Hf_0.5Zr_0.5C matrix (11 cycles) and SiC matrix (9 cycles) into the carbon cloth preform through precursor impregnation and pyrolysis (PIP) process. The influence of the introduction time of SiC matrix on the microstructure and mechanical properties of C_f/Hf_0.5Zr_0.5C-SiC composites was studied, and the results show that with the increase of the PIP cycles of the SiC matrix introduced before Hf_0.5Zr_0.5C matrix, the composite open porosity decreased, and the flexural strength and modulus presented an obvious upward trend. CS45 sample, which has 4 cycles of PIP SiC introduced in advance, has the highest flexural strength, flexural modulus and interfacial shear strength of 402.73 ± 35.73 MPa, 56.92 ± 3.97 GPa and 100.88 ± 7.79 MPa, respectively. Hf_0.5Zr_0.5C matrix has a loose and porous structure, so when more SiC matrix was introduced in advance, its covering effect on the surface of fibers led to less intra-bundle pores and thusly denser composite structure, and due to the compactness of SiC matrix, better overall bonding of fiber, interface and matrix was achieved, as well as better load transfer effect, which led to obvious interfacial debonding and cracking based on the in-situ SEM observation during flexural tests. While in the sample without pre-introduced SiC, the cracking occurred mainly between the interface and porous matrix and the overall performance of the material was poor.     

Exploring the influences of the counterpart materials on friction and wear behaviors of atmospheric plasma-sprayed YSZ coating

Sliding wear behaviors of atmospheric plasma-sprayed Yttria Stabilized Zirconia (YSZ) coating mated with four metallic or ceramic counterparts (Si₃N₄, Al₂O₃, GCr15 and ZrO₂) were investigated. It has been found that YSZ coatings in contact with Si₃N₄ and GCr15 show better tribological performances than the other cases, which is due to the formation of the tribolayer mainly consisting of Si₃N₄ and Fe₂O₃ respectively on the worn surfaces. In the case of YSZ coating-Al₂O₃ and YSZ coating-ZrO₂ tribopairs, the wear debris are more irregular and larger in size, resulting in severe abrasive wear and brittle fracture of debris particles. In particular, the specific wear rate of YSZ coating sliding against GCr15 is negative due to the significant material transfer of the tribo-oxide layer, while that of YSZ coating sliding against ZrO₂ is the highest. Amorphization of the wear particles appears in the four cases due to the repeated mechanical action. It has been demonstrated that the wear of YSZ coating deteriorates with the increased flash temperature between the contact surfaces during rubbing process.     

A comparative study on pyrolysis reactivity and gas release characteristics of biomass and coal using TG-MS analysis

Pyrolysis reactivity and gas release characteristics of biomass and coals were comparatively investigated using TG-MS. In addition, chemical compositions and structures of tested samples were determined to correlate pyrolysis gas release characteristic. It was found that pyrolysis reactivity and gaseous product release were hardly varied with pyrolysis heating rate. Furthermore, pyrolysis rates of two biomass samples were greater than those of coals, which were mainly attributed to the chemical compositions and the gaseous product evolution process. The result also showed that gaseous product release during pyrolysis process was related to the presence of different functional groups in samples.     

Tailoring Cu/Al2O3 catalysts for the catalytic pyrolysis of tomato waste

In this study, pyrolysis of tomato waste has been performed in fixed bed tubular reactor at 500 °C, both in absence and presence of Cu/Al₂O₃ catalyst. The influences of heating rate, catalyst preparation method and catalyst loading on bio-oil yields and properties were examined. According to pyrolysis experiments, the highest bio-oil yield was obtained as 30.31% with a heating rate of 100 °C/min, 5% Cu/Al₂O₃ catalyst loading ratio and co-precipitation method. Results showed that the catalysts have strong positive effect on bio-oil yields. Bio-oil quality obtained from fast catalytic pyrolysis was more favorable than that obtained from non-catalytic and slow catalytic pyrolysis.     

产教融合背景下高职特色专业群“平台+模块”课程体系建设研究

In view of the problems in the construction of characteristic professional groups in higher vocational colleges, the professional group of "intelligent manufacturing" is taken as the research object, and the "platform + module" suitable for the development of the industry will be constructed according to the content of the vocational ability planning courses of the post group. The curriculum system establishes the framework of professional groups, and explores and forms a strategic study to optimize and integrate professional group resources.     

Analyzing dissipation effects on the non-classicality witnessing by a qubit via the entangled state representation

ABSTRACT

In this paper, we study detection of the state non-classicality for a quantum harmonic oscillator by a qubit in the presence of dissipation effects. We show that dissipation can enhance the effectiveness of the method in case of using the corrected form of the related nonclassicality witness. Such an improvement is attributed to the fact that dissipation leads to probing a surface, instead of a curve, of the complex plane for non-classicality condition on normally-ordered characteristic function.     

基于气动性能与刚度特性的风力机翼型优化设计

结合翼型泛函集成理论与叶片截面刚度矩阵数学计算模型,提出了风力机中等厚度翼型气动性能与结构刚度特性的一体化设计方法,实现了翼型气动性能与叶片截面刚度特性的同时提高。对考虑叶片截面铺层参数变化设计的WQ-B300翼型与DU97-W-300翼型进行了气动性能与结构刚度特性对比分析,结果表明:相比于DU97-W-300翼型,WQ-B300翼型的气动性能与叶片截面刚度性能均有显著提高,其挥舞刚度和摆振刚度分别提高了6.2%和8.4%,验证了该设计方法的可行性,给风力机中等厚度及大厚度翼型设计提供了一种思路。     

双光束激光焊匙孔动态特征分析

文中研究了高功率单光束激光焊与双光束激光焊过程中匙孔动态特征的差别. 结果表明，单光束激光焊及双光束激光焊接过程中匙孔均处于从产生到湮灭的剧烈波动的过程，不同于单光束激光焊匙孔的形成、长大、维持、缩小、湮灭过程，双光束激光焊的匙孔还存在分离长大及合并缩小的过程；在相同的焊接参数及焊缝具有相同熔深的条件下，双光束激光焊匙孔的波动频率约为单光束激光焊的2/3，单光束激光焊匙孔的开口面积均值约为双光束激光焊匙孔开口面积的1/2，开口面积的波动变异系数约为单光束激光的2倍，即双光束激光焊过程中匙孔较单光束激光焊的具有较高稳定性.