带有方形肋及双倾斜肋片的细通道内流动、传热和熵产分析

为了探究带有方形肋及双倾斜肋片细通道的流动换热及熵产特性，设计了2种带有方形肋及双倾斜肋片的组合细通道(MCDS-L, MCDS-R)，然后采用数值模拟的方法分析其流动特性、传热特性和熵产特性，并将其分析结果同2种方形肋细通道(MCS-L, MCS-R)和一种双倾斜肋片细通道(MCD)进行对比。结果表明，在所研究的雷诺数范围内，组合通道的摩擦阻力系数基本一致且均高于其他3组通道(MCS-L, MCS-R, MCD) 。此外，组合通道的努塞尔数均高于其他3组通道，而熵产增大数均低于其他3组通道。其中，MCDS-L通道的努塞尔数最大，熵产增大数最低。表明MCDS-L通道的换热效果最佳，能量的综合利用程度最高。研究成果为微细通道热沉的设计提供参考。     

重载齿轮齿面疲劳损坏及预防

点蚀和剥落是重载齿轮齿面疲劳损坏最普遍的形式.根据齿轮失效分析实例,对齿面初始点蚀、破坏性点蚀和齿面剥落等三种主要疲劳损坏的特征、发生部位及破损危害程度进行了分析研究,较系统地论述了齿轮接触疲劳破坏机理,影响因素及其产生原因,并对有关的齿面破坏提出了相应的预防措施.     

分析矩形光波导损耗的简易方法

利用有效折射率和修正的有效折射率方法对矩形光波导的损耗作了简单有效的分析，并且计算出了纵向传播系数和衰减系数的大小。     

非理想截面脊形介质光波导导波模式的研究

提出了一种求解任意截面形状脊形光波导的方法，先利用有效折射率的概念解出某种截面形状脊形光波导的等效折射率，再利用转移矩阵的理论求解出波导的模式色散方程。     

Effect of specimen size and loading conditions on spalling of concrete

Different qualities of concrete have been fire tested using different geometries of the specimens as well as different load levels and load configurations. The main objective with the study was to examine a test methodology consisting of a full‐scale test and different small scale‐tests for determining the probability of spalling and the amount of spalling of fire exposed concrete structures. A reference specimen was defined as a one‐sided fire exposed slab with the dimensions 1800 × 1200 mm² giving an exposed area of 1500 × 1200 mm². A number of concrete qualities with different probabilities for spalling, were tested using the reference specimen. These tests showed that the reference specimens worked well giving the expected test results. Small specimens were manufactured in different shapes with the same concrete as the one used in the reference tests. These small specimens were tested either at the same time as the reference specimens in the large furnace or afterwards on a small‐scale furnace where the fire exposed surface was 450 × 360 mm². The test results clearly show the increased probability and the increased amount of spalling by using external compressive loading. The results also show that by using pre‐stress through bars or wires the load can be lost due to heating of the bars/wires which results in a decreased amount of spalling. The boundary of the specimen also affects the amount of spalling. The spalling around the edges was in all tests less than the spalling on the central parts of the exposed area. It could also be noted that the spalling did not pass completely through any of the specimens. The reason for this is probably that the water/vapour could migrate out from the unexposed surface of the specimen. Copyright © 2006 John Wiley & Sons, Ltd.     

A TVD Scheme for Incompressible Flow Coupled With Different Turbulence Modles on A Ground-Mounted Square-RIB Flow

A finite-difference Total Variation Diminishing (TVD) numerical simulation model for coupling the Reynolds Averaged Navier-Stokes (RANS) equations, pressure-relative continuity equation and various k-ε turbulence models was developed to solve the incompressible flow based on the pseudo-compressibility method. The hyperbolicity of all these equations was studied and the discretization of the fully coupling equations with all the primal variables and source terms were made in this article. Numerical simulation for modeling the flow around a ground-mounted square rib was implemented and validated by comparing with the published wind tunnel experimental data. It is shown that such a numerical simulation method with a proper turbulence model has a very good accuracy to simulate the flow around a surface-mounted rib. It is concluded that the Renormalization Group (RNG) and Chen-Kim k-ε turbulence models have much better ability to predict the characteristics of the vortex structure and flow separation than the standard k-ε model.     

浅谈中承式钢管拱肋单拱桥的施工方法

右江平圩大桥钢管拱肋的制作、拼装、吊装、混凝土灌注的施工方法及注意事项 ,事故原因分析及处理。     

控制W9Cr3Mo4V低倍碳化物剥落的工艺改进

针对W9Cr3M04V轧制成品材低倍碳化物剥落的形成原因分析，得出一次碳化物颗粒粗大、在1／4D至中心区域聚集是导致低倍热酸浸试验碳化物剥落的主因；由此进行冶炼过程中注速（锭形）、浇注温度选择对比工艺试验，得出在原有冶炼＋轧制的工艺基础上选用2．2t锭、降低浇注温度（1489℃）能有效改善一次碳化物颗粒大小和聚集程度，进而有效降低低倍碳化物剥落倾向。     

Pore‐free mold‐pattern‐transfer method for barrier ribs of HD PDPs

Abstract— Among various barrier‐rib manufacturing processes, the mold‐pattern‐transfer method has potential to reduce processing cost as well as the manufacture of high‐resolution pixels. In this study, the effects of major processing variables of the mold‐pattern‐transfer process on the formation of air‐trapped pores within barrier ribs were examined. The results indicated that with an optimum combination of the processing variables, barrier ribs without trapped defects can be produced, demonstrating the possibility of reducing the number of processing steps and costs of barrier ribs.     

Effect of intensified discharge in the vicinity of ribs on PDP performance

It was determined that the discharge in the vicinity of ribs should be intensified to obtain low‐voltage, high‐luminous efficacy, and high module efficiency. One possible way is to increase the space between ribs and the discharge surface. Even if the amount of space increases by only 2 or 3 µm, it still results in low discharge voltage, large discharge current, and high luminous efficacy. For that reason it might be important to control the micron‐sized particles included in the MgO crystal dispersed layers. Another preferable way is to use ribs with a low electric permittivity (ε) that are represented by porous ribs. Moreover, low‐ε ribs diffuses the high‐energy spots in plasma, resulting in a high luminous efficacy. They feature a significantly lower sustain voltage and a smaller parasitic capacitance as well to facilitate a help high module efficiency. Also, highly porous ribs are expected to increase their practical use in aspects of mechanical strength and impurity gas exhaustion.