MHD mixed convection of a Cu–water nanofluid flow through a channel with an open trapezoidal cavity and an elliptical obstacle

In the current work, numerical simulations are achieved to study the properties and the characteristics of fluid flow and heat transfer of (Cu–water) nanofluid under the magnetohydrodynamic effects in a horizontal rectangular canal with an open trapezoidal enclosure and an elliptical obstacle. The cavity lower wall is grooved and represents the heat source while the obstacle represents a stationary cold wall. On the other hand, the rest of the walls are considered adiabatic. The governing equations for this investigation are formulated, nondimensionalized, and then solved by Galerkin finite element approach. The numerical findings were examined across a wide range of Richardson number (0.1 ≤ Ri ≤ 10), Reynolds number (1 ≤ Re ≤ 125), Hartmann number (0 ≤ Ha ≤ 100), and volume fraction of nanofluid (0 ≤ φ ≤ 0.05). The current study's findings demonstrate that the flow strength increases inversely as the Reynolds number rises, which pushes the isotherms down to the lower part of the trapezoidal cavity. The Nu_avg rises as the Ri rise, the maximum Nu_avg = 10.345 at Ri = 10, Re = 50, ϕ = 0.05, and Ha = 0; however, it reduces with increasing Hartmann number. Also, it increase by increasing ϕ, at Ri = 10, the Nu_avg increased by 8.44% when the volume fraction of nanofluid increased from (ϕ = 0–0.05).     

Experimental Investigation of Heat Storage and Heat Transfer Rates during Melting of Nano-Enhanced Phase Change Materials (NePCM) in a Differentially-Heated Rectangular Cavity

In this work, an experimental study of melting heat transfer of nano-enhanced phase change materials(NePCM) in a differentially-heated rectangular cavity was performed. Two height-to-width aspect ratios of the cavity, i.e., 0.9 and 1.5, were investigated. The model Ne PCM samples were prepared by dispersing graphene nanoplatelets(GNP) into 1-tetradecanol, having a nominal melting point of 37℃, at loadings up to 3 wt.%. The viscosity was found to have a more than 10-fold increase at the highest loading of GNP. During the melting experiments, the wall superheat at the heating boundary was set to be 10℃ or 30℃. It was shown that with increasing the loading of GNP, both the heat storage and heat transfer rates during melting decelerate to some extent, at all geometrical and thermal configurations. This suggested that the use of NePCM in such cavity may not be able to enhance the heat storage rate due to the dramatic growth in viscosity, which deteriorates significantly natural convective heat transfer during melting to overweigh the enhanced heat conduction by only a decent increase in thermal conductivity. This also suggested that the numerically predicted melting accelerations and heat transfer enhancements, as a result of the increased thermal conductivity, in the literature are likely overestimated because the negative effects due to viscosity growth are underestimated.     

太赫兹可调谐滤波器设计

为了实现太赫兹信号的可调谐滤波，设计了一种基于柔性材料的太赫兹可调谐滤波器。通过扭曲特氟龙（Teflon）波导形成环型谐振器，实现了160～200 GHz频段的带阻滤波功能。改变谐振腔长可实现自由频谱范围（FSR）和滤波频点的调谐，实验测试了自由频谱范围在1.9 GHz和2.8 GHz间切换以及相应的滤波特性。研究表明，谐振腔长一定时，改变弯曲半径可实现滤波阻带抑制度的调节，柔性材料太赫兹环型谐振器可用于可调谐滤波，且具有较高的自由度。     

高温气冷堆舱室抗商用飞机撞击的耦合数值分析

本文建立了大型商用飞机撞击典型高温气冷堆核电站反应堆舱室的非线性有限元模型，计算中混凝土舱室直接采用工程用钢筋混凝土的损伤塑性本构模型，飞机结构采用Johnson-Cook本构模型。对飞机高速撞击高温气冷堆核电站反应堆舱室非线性撞击过程进行模拟计算，得出正面和侧面撞击条件下的撞击载荷曲线、撞击位移云图、反应堆舱室混凝土破坏情况等结果。评估表明，反应堆舱室结构在撞击条件下的整体损伤微小，可为保护内部关键设备提供重要的屏障功能。     

A new design strategy for DC/DC LLC resonant converter: Concept,modeling, and fabrication

In this paper, a new design procedure for LLC converter has been introduced. In fact, this method is a computer-based design algorithm based on a numerical technique. In the process of designing, the value of the resonant element is obtained by solving the LLC converter fundamental equation. This converter will be controlled by using state feedback, such as output voltage variable. As a matter of fact, in a control system, the change of output voltage (because of load variation) will affect the switching frequency, so the output voltage will be tuned. In the designing process, the fundamental equations of LLC converter are obtained, and the value of the resonant elements is calculated. Also, a comparison analysis is carried out between the proposed and typical methods. The simulation is done to investigate the validity of the proposed method. Moreover, a prototype is manufactured, and the experimental test is done to evaluate its applicability.     

The microstructure of buccal cavity and alimentary canal of Siganus rivulatus: Scanning electron microscope study

The microstructure of the oral cavity and alimentary canal of herbivorous fish Siganus rivulatus collected from the Red Sea were investigated by using scanning electron microscope (SEM). The results showed that S. rivulatus has three types of teeth, tri‐cusped, bi‐cusped, and papilliform. A taste bud (Type I) was recorded in the oropharyngeal cavity. Characteristic styles of microridges on the cell's surface inside the buccal cavity were recorded. Also, the distribution of the mucous cells in the lining of the mouth cavity, alimentary canal was observed. Mucosal folds along the distinct parts of alimentary canal, showed characteristic pattern which was complex in the intestinal mucosa. The results concluded that there are characteristic microstructures according to feeding habitat compared with other bony fishes.     

Ultralow-threshold wideband-tunable single-mode ultraviolet lasing from lanthanide-doped upconversion nanomaterials

Ultraviolet (UV) lasers with dynamic wavelength-tunability and high monochromaticity are crucial in a multitude of practical applications yet still remarkable challenges. Here, we show wide wavelength-tuning of single-mode UV lasing based on lanthanide-doped upconversion nanoparticles (UCNPs). The rationally designed Yb³⁺/Er³⁺/Tm³⁺/Gd³⁺/Ce³⁺ co-doped multilayer UCNPs, which exhibits a broad gain spectrum with the full width of half maximum of around 57 nm in the UV regime, are developed. More importantly, by taking advantages of a diffraction grating as the tuning component, stable single-mode emission can be achieved in the UCNPs-based external-cavity-extended Fabry–Pérot laser at room temperature. Specifically, the lasing threshold is around 137 µJ cm^–2, which is two orders of magnitude lower than that in the previously reported articles. Precise wavelength-tuning from 310 to 363 nm can be realized by adjusting the Littrow angle. This achievement highlights a portable alternative to continuously wideband-tunable UV lasers and opens up new opportunities for constructing compact solid-state UV photon sources.     

腔磁力系统中的诱导透明和快慢光传播

为了在腔磁力系统中实现可控的磁子诱导透明、磁力诱导透明以及快慢光传播,建立了一个混合腔磁力系统.该系统由一个含有YIG球的微波腔和在z方向对球施加一个均匀的偏置磁场组成,并用强泵浦场驱动磁子和弱探测场驱动微波腔.研究表明,通过调节腔与磁子之间的相互作用强度和微波腔与磁子的耗散比,可以增加磁子诱导透明(MIT)、磁力诱导透明(MMIT)的效果和提高快慢光传播的速度.该研究结果可为磁力诱导放大、量子光学操纵和量子信息存储以及灵敏光开关的研究提供参考.     

Biomechanical response of the human foot when standing in a natural position while exposed to vertical vibration from 10–200 Hz

Exposure to foot-transmitted vibration (FTV) can lead to pain and numbness in the toes and feet, increased cold sensitivity, blanching in the toes, and joint pain. Prolonged exposure can result in a clinical diagnosis of vibration-induced white foot (VIWFt). Data on the biomechanical response of the feet to FTV is limited; therefore, this study seeks to identify resonant frequencies for different anatomical locations on the human foot, while standing in a natural position. A laser Doppler vibrometer was used to measure vertical (z-axis) vibration on 21 participants at 24 anatomical locations on the right foot during exposure to a sine sweep from 10–200?Hz with a peak vertical velocity of 30?mm/s. The most notable differences in the average peak frequency occur between the toes (range: 99–147?Hz), midfoot (range: 51–84?Hz) and ankle (range: 16–39?Hz).

Practitioner Summary: The biomechanical response of the human foot exposed to foot-transmitted vibration, when standing in a natural position, was measured for 21 participants. The foot does not respond uniformly; the toes, midfoot, and ankle regions need to be considered independently in future development of isolation strategies and protective measures.     

环境气压对掺气设施空腔长度的影响分析

低气压环境下泄水建筑物空化空蚀风险增大,环境气压对掺气减蚀效果的影响程度是高海拔地区高坝水力设计时需重点关注的问题。采用CFD数值仿真方法,建立跌坎和挑坎两种不同体型的掺气设施模型,分析不同环境气压下的掺气设施的空腔长度,研究环境气压对高速水流掺气效果的影响。结果表明,环境气压越低,高速水流掺气空腔长度越小,掺气效果越弱,高海拔地区高速水流防蚀设计应合理考虑环境气压的影响程度。